Keith Bennett
3 years ago
committed by
GitHub
GitHub
17 changed files with 407 additions and 84 deletions
@ -0,0 +1,223 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
|
|||
#pragma once |
|||
|
|||
#if NOT_TARGET(STM32F4) |
|||
#error "Oops! Select an STM32F4 board in 'Tools > Board.'" |
|||
#elif HOTENDS > 1 || E_STEPPERS > 1 |
|||
#error "Anet ET4 only supports one hotend / E-stepper. Comment out this line to continue." |
|||
#endif |
|||
|
|||
#ifndef BOARD_INFO_NAME |
|||
#define BOARD_INFO_NAME "Anet ET4 1.x" |
|||
#endif |
|||
|
|||
//
|
|||
// EEPROM
|
|||
//
|
|||
|
|||
// Use one of these or SDCard-based Emulation will be used
|
|||
#if NO_EEPROM_SELECTED |
|||
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
|||
#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
|
|||
//#define IIC_BL24CXX_EEPROM // Use I2C EEPROM onboard IC (AT24C04C, Size 4KB, PageSize 16B)
|
|||
#endif |
|||
|
|||
#if ENABLED(FLASH_EEPROM_EMULATION) |
|||
// Decrease delays and flash wear by spreading writes across the
|
|||
// 128 kB sector allocated for EEPROM emulation.
|
|||
#define FLASH_EEPROM_LEVELING |
|||
#elif ENABLED(IIC_BL24CXX_EEPROM) |
|||
#define IIC_EEPROM_SDA PB11 |
|||
#define IIC_EEPROM_SCL PB10 |
|||
#define EEPROM_DEVICE_ADDRESS 0xA0 |
|||
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
|||
#endif |
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#define X_STOP_PIN PC13 |
|||
#define Y_STOP_PIN PE12 |
|||
#define Z_STOP_PIN PE11 |
|||
|
|||
//
|
|||
// Z Probe
|
|||
//
|
|||
#if ENABLED(BLTOUCH) |
|||
#error "You will need to use 24V to 5V converter and remove one resistor and capacitor from the motherboard. See https://github.com/davidtgbe/Marlin/blob/bugfix-2.0.x/docs/Tutorials/bltouch-en.md for more information. Comment out this line to proceed at your own risk."
|
|||
#define SERVO0_PIN PC3 |
|||
#elif !defined(Z_MIN_PROBE_PIN) |
|||
#define Z_MIN_PROBE_PIN PC3 |
|||
#endif |
|||
|
|||
//
|
|||
// Filament Runout Sensor
|
|||
//
|
|||
#ifndef FIL_RUNOUT_PIN |
|||
#define FIL_RUNOUT_PIN PA2 |
|||
#endif |
|||
|
|||
//
|
|||
// Power Loss Detection
|
|||
//
|
|||
#ifndef POWER_LOSS_PIN |
|||
#define POWER_LOSS_PIN PA8 |
|||
#endif |
|||
|
|||
//
|
|||
// LED PIN
|
|||
//
|
|||
#define LED_PIN PD12 |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_STEP_PIN PB6 |
|||
#define X_DIR_PIN PB5 |
|||
#define X_ENABLE_PIN PB7 |
|||
|
|||
#define Y_STEP_PIN PB3 |
|||
#define Y_DIR_PIN PD6 |
|||
#define Y_ENABLE_PIN PB4 |
|||
|
|||
#define Z_STEP_PIN PA12 |
|||
#define Z_DIR_PIN PA11 |
|||
#define Z_ENABLE_PIN PA15 |
|||
|
|||
#define E0_STEP_PIN PB9 |
|||
#define E0_DIR_PIN PB8 |
|||
#define E0_ENABLE_PIN PE0 |
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
//
|
|||
#define TEMP_0_PIN PA1 |
|||
#define TEMP_BED_PIN PA4 |
|||
|
|||
//
|
|||
// Heaters
|
|||
//
|
|||
#define HEATER_0_PIN PA0 |
|||
#define HEATER_BED_PIN PE2 |
|||
|
|||
//
|
|||
// Fans
|
|||
//
|
|||
#define FAN_PIN PE3 // Layer fan
|
|||
#define FAN1_PIN PE1 // Hotend fan
|
|||
|
|||
#ifndef E0_AUTO_FAN_PIN |
|||
#define E0_AUTO_FAN_PIN FAN1_PIN |
|||
#endif |
|||
|
|||
//
|
|||
// LCD / Controller
|
|||
//
|
|||
#define TFT_RESET_PIN PE6 |
|||
#define TFT_CS_PIN PD7 |
|||
#define TFT_RS_PIN PD13 |
|||
#define TFT_INTERFACE_FSMC_8BIT |
|||
|
|||
//
|
|||
// Touch Screen
|
|||
// https://ldm-systems.ru/f/doc/catalog/HY-TFT-2,8/XPT2046.pdf
|
|||
//
|
|||
#if ENABLED(TOUCH_SCREEN) |
|||
#define TOUCH_CS_PIN PB2 |
|||
#define TOUCH_SCK_PIN PB0 |
|||
#define TOUCH_MOSI_PIN PE5 |
|||
#define TOUCH_MISO_PIN PE4 |
|||
#define TOUCH_INT_PIN PB1 |
|||
#endif |
|||
|
|||
// Touchscreen calibration does not work correctly with ANET_ET5_TFT35 or ANET_ET4_TFT28
|
|||
#if ENABLED(TOUCH_SCREEN_CALIBRATION) |
|||
#undef TOUCH_SCREEN_CALIBRATION |
|||
#endif |
|||
|
|||
#if ENABLED(ANET_ET5_TFT35) |
|||
#ifndef TOUCH_CALIBRATION_X |
|||
#define TOUCH_CALIBRATION_X 17125 |
|||
#endif |
|||
#ifndef TOUCH_CALIBRATION_Y |
|||
#define TOUCH_CALIBRATION_Y -11307 |
|||
#endif |
|||
#ifndef TOUCH_OFFSET_X |
|||
#define TOUCH_OFFSET_X -26 |
|||
#endif |
|||
#ifndef TOUCH_OFFSET_Y |
|||
#define TOUCH_OFFSET_Y 337 |
|||
#endif |
|||
#ifndef TOUCH_ORIENTATION |
|||
#define TOUCH_ORIENTATION TOUCH_PORTRAIT |
|||
#endif |
|||
#elif ENABLED(ANET_ET4_TFT28) |
|||
#ifndef TOUCH_CALIBRATION_X |
|||
#define TOUCH_CALIBRATION_X -11838 |
|||
#endif |
|||
#ifndef TOUCH_CALIBRATION_Y |
|||
#define TOUCH_CALIBRATION_Y 8776 |
|||
#endif |
|||
#ifndef TOUCH_OFFSET_X |
|||
#define TOUCH_OFFSET_X 333 |
|||
#endif |
|||
#ifndef TOUCH_OFFSET_Y |
|||
#define TOUCH_OFFSET_Y -17 |
|||
#endif |
|||
#ifndef TOUCH_ORIENTATION |
|||
#define TOUCH_ORIENTATION TOUCH_PORTRAIT |
|||
#endif |
|||
#endif |
|||
|
|||
//
|
|||
// SD Card
|
|||
//
|
|||
//#define SDIO_SUPPORT
|
|||
|
|||
#ifndef SDCARD_CONNECTION |
|||
#define SDCARD_CONNECTION CUSTOM_CABLE |
|||
#endif |
|||
|
|||
#if ENABLED(SDSUPPORT) |
|||
|
|||
#define SDIO_D0_PIN PC8 |
|||
#define SDIO_D1_PIN PC9 |
|||
#define SDIO_D2_PIN PC10 |
|||
#define SDIO_D3_PIN PC11 |
|||
#define SDIO_CK_PIN PC12 |
|||
#define SDIO_CMD_PIN PD2 |
|||
|
|||
#if DISABLED(SDIO_SUPPORT) |
|||
#define SOFTWARE_SPI |
|||
#define SDSS SDIO_D3_PIN |
|||
#define SCK_PIN SDIO_CK_PIN |
|||
#define MISO_PIN SDIO_D0_PIN |
|||
#define MOSI_PIN SDIO_CMD_PIN |
|||
#endif |
|||
|
|||
#ifndef SD_DETECT_PIN |
|||
#define SD_DETECT_PIN PD3 |
|||
#endif |
|||
|
|||
#endif |
|||
@ -0,0 +1,34 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
|
|||
#pragma once |
|||
|
|||
#define BOARD_INFO_NAME "Anet ET4P 1.x" |
|||
|
|||
//
|
|||
// TMC2208 Configuration_adv defaults for Anet ET4P-MB_V1.x
|
|||
//
|
|||
#if !AXIS_DRIVER_TYPE_X(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_Y(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_Z(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_E0(TMC2208_STANDALONE) |
|||
#error "ANET_ET4P requires ([XYZ]|E0)_DRIVER_TYPE set to TMC2208_STANDALONE." |
|||
#endif |
|||
|
|||
#include "pins_ANET_ET4.h" |
|||
Loading…
Reference in new issue