Browse Source

Other spacing tweaks

pull/1/head
Scott Lahteine 7 years ago
parent
commit
a037ddbf7b
  1. 8
      Marlin/dac_dac084s085.cpp
  2. 42
      Marlin/stepper.cpp
  3. 2
      Marlin/twibus.cpp

8
Marlin/dac_dac084s085.cpp

@ -17,10 +17,10 @@
uint8_t externalDac_buf[2] = {0x20,0x00};//all off
// All SPI chip-select HIGH
pinMode (DAC0_SYNC, OUTPUT);
pinMode(DAC0_SYNC, OUTPUT);
digitalWrite( DAC0_SYNC , HIGH );
#if EXTRUDERS > 1
pinMode (DAC1_SYNC, OUTPUT);
pinMode(DAC1_SYNC, OUTPUT);
digitalWrite( DAC1_SYNC , HIGH );
#endif
digitalWrite( SPI_EEPROM1_CS , HIGH );
@ -68,8 +68,8 @@
else
externalDac_buf[0] |= (3 - channel << 6);
externalDac_buf[0] |= (value>>4);
externalDac_buf[1] |= (value<<4);
externalDac_buf[0] |= (value >> 4);
externalDac_buf[1] |= (value << 4);
// All SPI chip-select HIGH
digitalWrite( DAC0_SYNC , HIGH );

42
Marlin/stepper.cpp

@ -1136,27 +1136,27 @@ void Stepper::init() {
E_AXIS_INIT(4);
#endif
#ifdef ARDUINO_ARCH_AVR
// waveform generation = 0100 = CTC
SET_WGM(1, CTC_OCRnA);
// output mode = 00 (disconnected)
SET_COMA(1, NORMAL);
// Set the timer pre-scaler
// Generally we use a divider of 8, resulting in a 2MHz timer
// frequency on a 16MHz MCU. If you are going to change this, be
// sure to regenerate speed_lookuptable.h with
// create_speed_lookuptable.py
SET_CS(1, PRESCALER_8); // CS 2 = 1/8 prescaler
// Init Stepper ISR to 122 Hz for quick starting
OCR1A = 0x4000;
TCNT1 = 0;
#else
// Init Stepper ISR to 122 Hz for quick starting
HAL_timer_start(STEP_TIMER_NUM, 122);
#endif
#ifdef ARDUINO_ARCH_AVR
// waveform generation = 0100 = CTC
SET_WGM(1, CTC_OCRnA);
// output mode = 00 (disconnected)
SET_COMA(1, NORMAL);
// Set the timer pre-scaler
// Generally we use a divider of 8, resulting in a 2MHz timer
// frequency on a 16MHz MCU. If you are going to change this, be
// sure to regenerate speed_lookuptable.h with
// create_speed_lookuptable.py
SET_CS(1, PRESCALER_8); // CS 2 = 1/8 prescaler
// Init Stepper ISR to 122 Hz for quick starting
OCR1A = 0x4000;
TCNT1 = 0;
#else
// Init Stepper ISR to 122 Hz for quick starting
HAL_timer_start(STEP_TIMER_NUM, 122);
#endif
ENABLE_STEPPER_DRIVER_INTERRUPT();

2
Marlin/twibus.cpp

@ -94,7 +94,7 @@ void TWIBus::echoprefix(uint8_t bytes, const char prefix[], uint8_t adr) {
serialprintPGM(prefix);
SERIAL_ECHOPAIR(": from:", adr);
SERIAL_ECHOPAIR(" bytes:", bytes);
SERIAL_ECHOPGM (" data:");
SERIAL_ECHOPGM(" data:");
}
// static

Loading…
Cancel
Save