Browse Source

📺 FYSETC Mini 12864 2.1 pins for Creality V4 (#24624)

FB4S_WIFI^2^2
ellensp 2 years ago
committed by Scott Lahteine
parent
commit
9d9f303c5e
  1. 70
      Marlin/src/pins/stm32f1/pins_CREALITY_V4.h

70
Marlin/src/pins/stm32f1/pins_CREALITY_V4.h

@ -161,7 +161,7 @@
#define SDIO_SUPPORT
#define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer
#if ENABLED(CR10_STOCKDISPLAY)
#if EITHER(CR10_STOCKDISPLAY, FYSETC_MINI_12864_2_1)
#if ENABLED(RET6_12864_LCD)
@ -169,7 +169,7 @@
* RET6 12864 LCD
* ------
* PC6 | 1 2 | PB2
* PB10 | 3 4 | PE8
* PB10 | 3 4 | PB11
* PB14 5 6 | PB13
* PB12 | 7 8 | PB15
* GND | 9 10 | 5V
@ -179,16 +179,12 @@
#define EXP1_01_PIN PC6
#define EXP1_02_PIN PB2
#define EXP1_03_PIN PB10
#define EXP1_04_PIN PE8
#define EXP1_04_PIN PB11
#define EXP1_05_PIN PB14
#define EXP1_06_PIN PB13
#define EXP1_07_PIN PB12
#define EXP1_08_PIN PB15
#ifndef HAS_PIN_27_BOARD
#define BEEPER_PIN EXP1_01_PIN
#endif
#elif ENABLED(VET6_12864_LCD)
/**
@ -212,8 +208,11 @@
#define EXP1_08_PIN PA7
#else
#error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller."
#error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for the LCD with the Creality V4 controller."
#endif
#endif
#if ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS EXP1_07_PIN
#define LCD_PINS_ENABLE EXP1_08_PIN
@ -223,6 +222,10 @@
#define BTN_EN1 EXP1_03_PIN
#define BTN_EN2 EXP1_05_PIN
#ifndef HAS_PIN_27_BOARD
#define BEEPER_PIN EXP1_01_PIN
#endif
#elif ANY(HAS_DWIN_E3V2, IS_DWIN_MARLINUI, DWIN_VET6_CREALITY_LCD)
#if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI
@ -248,4 +251,55 @@
#define BEEPER_PIN EXP1_06_PIN
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING
#error "CAUTION! FYSETC_MINI_12864_2_1 and clones require wiring modifications. See 'pins_CREALITY_V4.h' for details. Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning"
#endif
#if SD_CONNECTION_IS(LCD)
#error "The LCD sdcard is not connected with this configuration"
#endif
/**
*
* Board (RET6 12864 LCD) Display
* ------ ------
* (EN1) PC6 | 1 2 | PB2 (BTN_ENC) 5V |10 9 | GND
* (LCD_CS) PB10 | 3 4 | PB11 (LCD RESET) -- | 8 7 | --
* (LCD_A0) PB14 5 6 | PB13 (EN2) (DIN) | 6 5 (LCD RESET)
* (LCD_SCK)PB12 | 7 8 | PB15 (MOSI) (LCD_A0) | 4 3 | (LCD_CS)
* GND | 9 10 | 5V (BTN_ENC) | 2 1 | --
* ------ ------
* EXP1 EXP1
*
* ------
* ----- -- |10 9 | --
* | 1 | VCC (RESET) | 8 7 | --
* | 2 | PA13 (DIN) (MOSI) | 6 5 (EN2)
* | 3 | PA14 -- | 4 3 | (EN1)
* | 4 | GND (LCD_SCK)| 2 1 | --
* ----- ------
* Debug port EXP2
*
* Needs custom cable. Connect EN2-EN2, LCD_CS-LCD_CS and so on.
* Debug port is just above EXP1, You need to add pins
*
*/
#define BTN_ENC EXP1_02_PIN
#define BTN_EN1 EXP1_01_PIN
#define BTN_EN2 EXP1_06_PIN
#define BEEPER_PIN -1
#define DOGLCD_CS EXP1_03_PIN
#define DOGLCD_A0 EXP1_05_PIN
#define DOGLCD_SCK EXP1_07_PIN
#define DOGLCD_MOSI EXP1_08_PIN
#define LCD_RESET_PIN EXP1_04_PIN
#define FORCE_SOFT_SPI
#define LCD_BACKLIGHT_PIN -1
#define NEOPIXEL_PIN PA13
#endif

Loading…
Cancel
Save