Clean up spacing in configs

Marlin/Configuration.h

@@ -853,11 +853,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/configurator/config/Configuration.h

@@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/Felix/Configuration.h

@@ -835,11 +835,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -799,11 +799,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/Hephestos/Configuration.h

@@ -844,11 +844,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/K8200/Configuration.h

@@ -840,11 +840,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/RigidBot/Configuration.h

@@ -842,11 +842,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -575,21 +575,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/SCARA/Configuration.h

@@ -860,11 +860,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/TAZ4/Configuration.h

@@ -871,11 +871,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -583,21 +583,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/WITBOX/Configuration.h

@@ -843,11 +843,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -977,11 +977,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/delta/biv2.5/Configuration_adv.h

@@ -581,21 +581,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/delta/generic/Configuration.h

@@ -982,11 +982,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -582,21 +582,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -982,11 +982,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -581,21 +581,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -972,11 +972,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -585,21 +585,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/makibox/Configuration.h

@@ -854,11 +854,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -579,21 +579,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -847,11 +847,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
 //#define FILAMENT_LCD_DISPLAY
 
-
-
-
-
-
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -580,21 +580,18 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E1_IS_L6470
-  #define E1_MICROSTEPS 16     //number of microsteps 
   #define E1_MICROSTEPS 16     //number of microsteps
   #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E2_IS_L6470
-  #define E2_MICROSTEPS 16     //number of microsteps 
   #define E2_MICROSTEPS 16     //number of microsteps
   #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
   #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
 
 //#define E3_IS_L6470
-  #define E3_MICROSTEPS 16     //number of microsteps   
   #define E3_MICROSTEPS 16     //number of microsteps
   #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high
   #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off