Fix G53/CNC_COORDINATE_SYSTEMS compilation, Travis testing (#10227)

.travis.yml

@@ -63,13 +63,13 @@ script:
   - opt_set TEMP_SENSOR_1 1
   - opt_set TEMP_SENSOR_BED 1
   - opt_set POWER_SUPPLY 1
-  - opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING ARC_P_CIRCLES CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS
+  - opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING
   - opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS
   - opt_enable BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR
   - opt_enable AUTO_BED_LEVELING_LINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE
-  - opt_enable_adv FWRETRACT MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING ADVANCED_PAUSE_FEATURE
+  - opt_enable_adv ARC_P_CIRCLES ADVANCED_PAUSE_FEATURE CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS
-  - opt_set ABL_GRID_POINTS_X 16
+  - opt_enable_adv FWRETRACT MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING
-  - opt_set ABL_GRID_POINTS_Y 16
+  - opt_set GRID_MAX_POINTS_X 16
   - opt_set_adv FANMUX0_PIN 53
   - build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}
   #
@@ -363,8 +363,7 @@ script:
   - opt_enable PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT M100_FREE_MEMORY_WATCHER
   - opt_enable_adv ADVANCED_PAUSE_FEATURE LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA PARK_HEAD_ON_PAUSE
   - opt_set_adv I2C_SLAVE_ADDRESS 63
-  - opt_set ABL_GRID_POINTS_X 16
+  - opt_set GRID_MAX_POINTS_X 16
-  - opt_set ABL_GRID_POINTS_Y 16
   - build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}
   #
   # Test a Sled Z Probe with Linear leveling

Marlin/src/gcode/geometry/G53-G59.cpp

@@ -24,6 +24,7 @@
 #include "../../module/motion.h"
 
 #if ENABLED(CNC_COORDINATE_SYSTEMS)
+
 #include "../../module/stepper.h"
 
 /**
@@ -58,7 +59,7 @@
  *
  * Marlin also uses G53 on a line by itself to go back to native space.
  */
-  inline void gcode_G53() {
+inline void GcodeSuite::G53() {
   const int8_t _system = active_coordinate_system;
   active_coordinate_system = -1;
   if (parser.chain()) { // If this command has more following...

Marlin/src/module/configuration_store.cpp

@@ -851,7 +851,7 @@ void MarlinSettings::postprocess() {
     _FIELD_TEST(coordinate_system);
 
     #if ENABLED(CNC_COORDINATE_SYSTEMS)
-      EEPROM_WRITE(coordinate_system); // 27 floats
+      EEPROM_WRITE(gcode.coordinate_system); // 27 floats
     #else
       dummy = 0.0f;
       for (uint8_t q = MAX_COORDINATE_SYSTEMS * XYZ; q--;) EEPROM_WRITE(dummy);