Marcio Teixeira
7 years ago
committed by
Scott Lahteine
Scott Lahteine
5 changed files with 213 additions and 35 deletions
@ -0,0 +1,193 @@ |
|||||
|
/**
|
||||
|
* Marlin 3D Printer Firmware |
||||
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
|
* |
||||
|
* Based on Sprinter and grbl. |
||||
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm |
||||
|
* |
||||
|
* This program is free software: you can redistribute it and/or modify |
||||
|
* it under the terms of the GNU General Public License as published by |
||||
|
* the Free Software Foundation, either version 3 of the License, or |
||||
|
* (at your option) any later version. |
||||
|
* |
||||
|
* This program is distributed in the hope that it will be useful, |
||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
||||
|
* GNU General Public License for more details. |
||||
|
* |
||||
|
* You should have received a copy of the GNU General Public License |
||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
* |
||||
|
*/ |
||||
|
|
||||
|
/**
|
||||
|
* Einsy-Retro pin assignments |
||||
|
*/ |
||||
|
|
||||
|
#ifndef __AVR_ATmega2560__ |
||||
|
#error "Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu." |
||||
|
#endif |
||||
|
|
||||
|
#define BOARD_NAME "Einsy Retro" |
||||
|
|
||||
|
//
|
||||
|
// TMC2130 Configuration_adv defaults for EinsyRetro
|
||||
|
//
|
||||
|
#if DISABLED(HAVE_TMC2130) |
||||
|
#error "You must enable TMC2130 support in Configuration_adv.h for EinsyRetro." |
||||
|
#elif DISABLED(X_IS_TMC2130) || DISABLED(Y_IS_TMC2130) || DISABLED(Z_IS_TMC2130) || DISABLED(E0_IS_TMC2130) |
||||
|
#error "You must enable ([XYZ]|E0)_IS_TMC2130 in Configuration_adv.h for EinsyRetro." |
||||
|
#endif |
||||
|
|
||||
|
// TMC2130 Diag Pins (currently just for reference)
|
||||
|
#define X_DIAG_PIN 64 |
||||
|
#define Y_DIAG_PIN 69 |
||||
|
#define Z_DIAG_PIN 68 |
||||
|
#define E0_DIAG_PIN 65 |
||||
|
|
||||
|
//
|
||||
|
// Limit Switches
|
||||
|
//
|
||||
|
// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.
|
||||
|
// Otherwise use a physical endstop based configuration.
|
||||
|
//
|
||||
|
// SERVO0_PIN and Z_MIN_PIN configuration for BLTOUCH sensor when combined with SENSORLESS_HOMING.
|
||||
|
//
|
||||
|
|
||||
|
#if DISABLED(SENSORLESS_HOMING) |
||||
|
|
||||
|
#define X_MIN_PIN 12 |
||||
|
#define Y_MIN_PIN 11 |
||||
|
#define Z_MIN_PIN 10 |
||||
|
#define X_MAX_PIN 81 |
||||
|
#define Y_MAX_PIN 57 |
||||
|
|
||||
|
#else |
||||
|
|
||||
|
#if X_HOME_DIR == -1 |
||||
|
#define X_MIN_PIN X_DIAG_PIN |
||||
|
#define X_MAX_PIN 81 |
||||
|
#else |
||||
|
#define X_MIN_PIN 12 |
||||
|
#define X_MAX_PIN X_DIAG_PIN |
||||
|
#endif |
||||
|
|
||||
|
#if Y_HOME_DIR == -1 |
||||
|
#define Y_MIN_PIN Y_DIAG_PIN |
||||
|
#define Y_MAX_PIN 57 |
||||
|
#else |
||||
|
#define Y_MIN_PIN 11 |
||||
|
#define Y_MAX_PIN Y_DIAG_PIN |
||||
|
#endif |
||||
|
|
||||
|
#if ENABLED(BLTOUCH) |
||||
|
#define Z_MIN_PIN 11 // Y-MIN
|
||||
|
#define SERVO0_PIN 10 // Z-MIN
|
||||
|
#else |
||||
|
#define Z_MIN_PIN 10 |
||||
|
#endif |
||||
|
|
||||
|
#endif |
||||
|
|
||||
|
#define Z_MAX_PIN 7 |
||||
|
|
||||
|
//
|
||||
|
// Z Probe (when not Z_MIN_PIN)
|
||||
|
//
|
||||
|
#ifndef Z_MIN_PROBE_PIN |
||||
|
#define Z_MIN_PROBE_PIN 10 |
||||
|
#endif |
||||
|
|
||||
|
//
|
||||
|
// Steppers
|
||||
|
//
|
||||
|
#define X_STEP_PIN 37 |
||||
|
#define X_DIR_PIN 49 |
||||
|
#define X_ENABLE_PIN 29 |
||||
|
#define X_CS_PIN 41 |
||||
|
|
||||
|
#define Y_STEP_PIN 36 |
||||
|
#define Y_DIR_PIN 48 |
||||
|
#define Y_ENABLE_PIN 28 |
||||
|
#define Y_CS_PIN 39 |
||||
|
|
||||
|
#define Z_STEP_PIN 35 |
||||
|
#define Z_DIR_PIN 47 |
||||
|
#define Z_ENABLE_PIN 27 |
||||
|
#define Z_CS_PIN 67 |
||||
|
|
||||
|
#define E0_STEP_PIN 34 |
||||
|
#define E0_DIR_PIN 43 |
||||
|
#define E0_ENABLE_PIN 26 |
||||
|
#define E0_CS_PIN 66 |
||||
|
|
||||
|
//
|
||||
|
// Temperature Sensors
|
||||
|
//
|
||||
|
#define TEMP_0_PIN 0 // Analog Input
|
||||
|
#define TEMP_1_PIN 1 // Analog Input
|
||||
|
#define TEMP_BED_PIN 2 // Analog Input
|
||||
|
|
||||
|
//
|
||||
|
// Heaters / Fans
|
||||
|
//
|
||||
|
#define HEATER_0_PIN 3 |
||||
|
#define HEATER_BED_PIN 4 |
||||
|
|
||||
|
#define FAN_PIN 8 |
||||
|
#define FAN1_PIN 6 |
||||
|
|
||||
|
//
|
||||
|
// Misc. Functions
|
||||
|
//
|
||||
|
#define SDSS 53 |
||||
|
#define LED_PIN 13 |
||||
|
#define CASE_LIGHT_PIN 9 |
||||
|
|
||||
|
//
|
||||
|
// M3/M4/M5 - Spindle/Laser Control
|
||||
|
//
|
||||
|
// use P1 connector for spindle pins
|
||||
|
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
|
||||
|
#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!
|
||||
|
#define SPINDLE_DIR_PIN 19 |
||||
|
|
||||
|
//
|
||||
|
// Průša i3 MK2 Multiplexer Support
|
||||
|
//
|
||||
|
#define E_MUX0_PIN 17 |
||||
|
#define E_MUX1_PIN 16 |
||||
|
#define E_MUX2_PIN 78 // 84 in MK2 Firmware, with BEEPER as 78
|
||||
|
|
||||
|
//
|
||||
|
// LCD / Controller
|
||||
|
//
|
||||
|
#if ENABLED(ULTRA_LCD) |
||||
|
|
||||
|
#define KILL_PIN 32 |
||||
|
|
||||
|
#if ENABLED(NEWPANEL) |
||||
|
|
||||
|
#if ENABLED(CR10_STOCKDISPLAY) |
||||
|
#define LCD_PINS_RS 85 |
||||
|
#define LCD_PINS_ENABLE 71 |
||||
|
#define LCD_PINS_D4 70 |
||||
|
#define BTN_EN1 18 |
||||
|
#define BTN_EN2 19 |
||||
|
#else |
||||
|
#define LCD_PINS_RS 82 |
||||
|
#define LCD_PINS_ENABLE 18 |
||||
|
#define LCD_PINS_D4 19 |
||||
|
#define LCD_PINS_D5 70 |
||||
|
#define LCD_PINS_D6 85 |
||||
|
#define LCD_PINS_D7 71 |
||||
|
#define BTN_EN1 14 |
||||
|
#define BTN_EN2 72 |
||||
|
#endif |
||||
|
|
||||
|
#define BTN_ENC 9 // AUX-2
|
||||
|
#define BEEPER_PIN 84 // AUX-4
|
||||
|
#define SD_DETECT_PIN 15 |
||||
|
|
||||
|
#endif // NEWPANEL
|
||||
|
#endif // ULTRA_LCD
|
||||
Loading…
Reference in new issue