Bob Kuhn
5 years ago
committed by
GitHub
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
3 changed files with
23 additions and
7 deletions
-
Marlin/src/HAL/shared/esp_wifi.cpp
-
Marlin/src/pins/pinsDebug_list.h
-
Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_V1_1.h
|
|
|
@ -23,13 +23,21 @@ |
|
|
|
#include "../../inc/MarlinConfig.h" |
|
|
|
#include "Delay.h" |
|
|
|
|
|
|
|
void esp_wifi_init(void) { |
|
|
|
void esp_wifi_init(void) { // init ESP01 WIFI module pins
|
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_GPIO0) |
|
|
|
OUT_WRITE(ESP_WIFI_MODULE_GPIO0_PIN, HIGH); |
|
|
|
#endif |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_GPIO2) |
|
|
|
OUT_WRITE(ESP_WIFI_MODULE_GPIO2_PIN, HIGH); |
|
|
|
#endif |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_RESET) |
|
|
|
delay(1); // power up delay (0.1mS minimum)
|
|
|
|
OUT_WRITE(ESP_WIFI_MODULE_RESET_PIN, LOW); |
|
|
|
delay(1); |
|
|
|
OUT_WRITE(ESP_WIFI_MODULE_RESET_PIN, HIGH); |
|
|
|
#endif |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_ENABLE) |
|
|
|
delay(1); // delay after reset released (0.1mS minimum)
|
|
|
|
OUT_WRITE(ESP_WIFI_MODULE_ENABLE_PIN, HIGH); |
|
|
|
#endif |
|
|
|
} |
|
|
|
|
|
|
|
@ -1415,3 +1415,9 @@ |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_ENABLE) |
|
|
|
REPORT_NAME_DIGITAL(__LINE__, ESP_WIFI_MODULE_ENABLE_PIN) |
|
|
|
#endif |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_GPIO0) |
|
|
|
REPORT_NAME_DIGITAL(__LINE__, ESP_WIFI_MODULE_GPIO0_PIN) |
|
|
|
#endif |
|
|
|
#if PIN_EXISTS(ESP_WIFI_MODULE_GPIO2) |
|
|
|
REPORT_NAME_DIGITAL(__LINE__, ESP_WIFI_MODULE_GPIO2_PIN) |
|
|
|
#endif |
|
|
|
|
|
|
|
@ -340,13 +340,15 @@ |
|
|
|
/**
|
|
|
|
* _____ |
|
|
|
* TX | 1 2 | GND Enable PG1 // Must be high for module to run
|
|
|
|
* Enable | 3 4 | GPIO2 Reset PG0 // Leave as unused (OK to leave floating)
|
|
|
|
* Reset | 5 6 | GPIO0 GPIO2 PF15 // Leave as unused (best to leave floating)
|
|
|
|
* 3.3V| 7 8 | RX GPIO0 PF14 // Leave as unused (best to leave floating)
|
|
|
|
* Enable | 3 4 | GPIO2 Reset PG0 // active low, probably OK to leave floating
|
|
|
|
* Reset | 5 6 | GPIO0 GPIO2 PF15 // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
|
|
* 3.3V| 7 8 | RX GPIO0 PF14 // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
|
|
* ￣￣ |
|
|
|
* W1 |
|
|
|
*/ |
|
|
|
#define ESP_WIFI_MODULE_COM 6 // Must also set SERIAL_PORT or SERIAL_PORT_2 to this
|
|
|
|
#define ESP_WIFI_MODULE_COM 6 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
|
|
|
|
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
|
|
|
|
#define ESP_WIFI_MODULE_RESET_PIN -1 |
|
|
|
#define ESP_WIFI_MODULE_RESET_PIN PG0 |
|
|
|
#define ESP_WIFI_MODULE_ENABLE_PIN PG1 |
|
|
|
#define ESP_WIFI_MODULE_GPIO0_PIN PF14 |
|
|
|
#define ESP_WIFI_MODULE_GPIO2_PIN PF15 |
|
|
|
|
