// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
#define AUTO_BED_LEVELING_GRID_POINTS 2
#else // not AUTO_BED_LEVELING_GRID
// with no grid, just probe 3 arbitrary points. A simple cross-product
// is used to esimate the plane of the print bed
#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 180
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20
#endif // AUTO_BED_LEVELING_GRID
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
@ -379,16 +417,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#endif
#endif
// with accurate bed leveling, the bed is sampled in a ACCURATE_BED_LEVELING_POINTSxACCURATE_BED_LEVELING_POINTS grid and least squares solution is calculated
#endif // ENABLE_AUTO_BED_LEVELING
// Note: this feature occupies 10'206 byte
#define ACCURATE_BED_LEVELING
#ifdef ACCURATE_BED_LEVELING
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
// G10 - retract filament according to settings of M207
// G10 - retract filament according to settings of M207
// G11 - retract recover filament according to settings of M208
// G11 - retract recover filament according to settings of M208
// G28 - Home all Axis
// G28 - Home all Axis
// G29 - Detailed Z-Probe, probes the bed at 3 points. You must de at the home position for this to work correctly.
// G29 - Detailed Z-Probe, probes the bed at 3 or more points. Will fail if you haven't homed yet.
// G30 - Single Z Probe, probes bed at current XY location.
// G30 - Single Z Probe, probes bed at current XY location.
// G90 - Use Absolute Coordinates
// G90 - Use Absolute Coordinates
// G91 - Use Relative Coordinates
// G91 - Use Relative Coordinates
// G92 - Set current position to cordinates given
// G92 - Set current position to coordinates given
// M Codes
// M Codes
// M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
// M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
@ -101,7 +101,7 @@
// M31 - Output time since last M109 or SD card start to serial
// M31 - Output time since last M109 or SD card start to serial
// M32 - Select file and start SD print (Can be used _while_ printing from SD card files):
// M32 - Select file and start SD print (Can be used _while_ printing from SD card files):
// syntax "M32 /path/filename#", or "M32 S<startpos bytes> !filename#"
// syntax "M32 /path/filename#", or "M32 S<startpos bytes> !filename#"
// Call gcode file : "M32 P !filename#" and return to caller file after finishing (simiarl to #include).
// Call gcode file : "M32 P !filename#" and return to caller file after finishing (similar to #include).
// The '#' is necessary when calling from within sd files, as it stops buffer prereading
// The '#' is necessary when calling from within sd files, as it stops buffer prereading
// M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
// M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
// M80 - Turn on Power Supply
// M80 - Turn on Power Supply
@ -127,18 +127,18 @@
// M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil)
// M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil)
// M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil)
// M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil)
// M140 - Set bed target temp
// M140 - Set bed target temp
// M150 - Set BlinkM Colour Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work.
// M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work.
// M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
// M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
// Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
// Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
// M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
// M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
// M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
// M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
// M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
// M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
// M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
// M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
// M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
// M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) in mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer under-runs and M20 minimum feedrate
// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
// M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
// M206 - set additional homeing offset
// M206 - set additional homing offset
// M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
// M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
// M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
// M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
// M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
// M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
// M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
// M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
// M220 S<factor in percent>- set speed factor override percentage
// M220 S<factor in percent>- set speed factor override percentage
@ -147,7 +147,7 @@
// M240 - Trigger a camera to take a photograph
// M240 - Trigger a camera to take a photograph
// M250 - Set LCD contrast C<contrast value> (value 0..63)
// M250 - Set LCD contrast C<contrast value> (value 0..63)
// M280 - set servo position absolute. P: servo index, S: angle or microseconds
// M280 - set servo position absolute. P: servo index, S: angle or microseconds
// M300 - Play beepsound S<frequency Hz> P<duration ms>
// M300 - Play beepsound S<frequency Hz> P<duration ms>
// M301 - Set PID parameters P I and D
// M301 - Set PID parameters P I and D
// M302 - Allow cold extrudes, or set the minimum extrude S<temperature>.
// M302 - Allow cold extrudes, or set the minimum extrude S<temperature>.
// M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
// M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
@ -155,14 +155,14 @@
// M400 - Finish all moves
// M400 - Finish all moves
// M401 - Lower z-probe if present
// M401 - Lower z-probe if present
// M402 - Raise z-probe if present
// M402 - Raise z-probe if present
// M500 - stores paramters in EEPROM
// M500 - stores parameters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
// M503 - print the current settings (from memory not from eeprom)
// M503 - print the current settings (from memory not from EEPROM)
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
// M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
// M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
// M665 - set delta configurations
// M665 - set delta configurations
// M666 - set delta endstop adjustemnt
// M666 - set delta endstop adjustment
// M605 - Set dual x-carriage movement mode: S<mode> [ X<duplication x-offset> R<duplication temp offset> ]
// M605 - Set dual x-carriage movement mode: S<mode> [ X<duplication x-offset> R<duplication temp offset> ]
// M907 - Set digital trimpot motor current using axis codes.
// M907 - Set digital trimpot motor current using axis codes.
#define MSG_ERR_STOPPED "Printer gestopt vanwege fouten. Los de fout op en gebruik M999 om opnieuw te starten. (Temperatuur is gereset, stel deze opnieuw in na herstart)"
volatileuint8_tbuttons;//Contains the bits of the currently pressed buttons.
volatileuint8_tbuttons;//Contains the bits of the currently pressed buttons.
#else
#else
volatileuint8_tbuttons_reprapworld_keypad;// to store the reprapworld_keypad shiftregister values
volatileuint8_tbuttons_reprapworld_keypad;// to store the reprapworld_keypad shiftregister values
#endif
#endif
#ifdef LCD_HAS_SLOW_BUTTONS
#ifdef LCD_HAS_SLOW_BUTTONS
volatileuint8_tslow_buttons;//Contains the bits of the currently pressed buttons.
volatileuint8_tslow_buttons;//Contains the bits of the currently pressed buttons.
@ -162,7 +162,7 @@ bool lcd_oldcardstatus;
menuFunc_tcurrentMenu=lcd_status_screen;/* function pointer to the currently active menu */
menuFunc_tcurrentMenu=lcd_status_screen;/* function pointer to the currently active menu */
uint32_tlcd_next_update_millis;
uint32_tlcd_next_update_millis;
uint8_tlcd_status_update_delay;
uint8_tlcd_status_update_delay;
uint8_tlcdDrawUpdate=2;/* Set to none-zero when the LCD needs to draw, decreased after every draw. Set to 2 in LCD routines so the LCD gets atleast 1 full redraw (first redraw is partial) */
uint8_tlcdDrawUpdate=2;/* Set to none-zero when the LCD needs to draw, decreased after every draw. Set to 2 in LCD routines so the LCD gets atleast 1 full redraw (first redraw is partial) */
//prevMenu and prevEncoderPosition are used to store the previous menu location when editing settings.
//prevMenu and prevEncoderPosition are used to store the previous menu location when editing settings.
menuFunc_tprevMenu=NULL;
menuFunc_tprevMenu=NULL;
@ -173,10 +173,10 @@ void* editValue;
int32_tminEditValue,maxEditValue;
int32_tminEditValue,maxEditValue;
menuFunc_tcallbackFunc;
menuFunc_tcallbackFunc;
// placeholders for Ki and Kd edits
// place-holders for Ki and Kd edits
floatraw_Ki,raw_Kd;
floatraw_Ki,raw_Kd;
/* Main status screen. It's up to the implementation specific part to show what is needed. As this is very display dependend */
/* Main status screen. It's up to the implementation specific part to show what is needed. As this is very display dependent */
Jim Morris
11 years ago