andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Set more regular setup in configuration.h

pull/1/head
alexborro 10 years ago
parent
60ceca1bc1
commit
8a4b62d081
1 changed files with 35 additions and 48 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Unified View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 83
      Marlin/Configuration.h

83
Marlin/Configuration.h
View File

@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
// The following define selects which electronics board you have. // The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup // Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD #ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_ULTIMAKER #define MOTHERBOARD BOARD_RAMPS_13
#endif #endif
// Define this to set a custom name for your generic Mendel, // Define this to set a custom name for your generic Mendel,
@ -123,8 +123,8 @@ Here are some standard links for getting your machine calibrated:
// #define DUMMY_THERMISTOR_998_VALUE 25 // #define DUMMY_THERMISTOR_998_VALUE 25
// #define DUMMY_THERMISTOR_999_VALUE 100 // #define DUMMY_THERMISTOR_999_VALUE 100
#define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 -1 #define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0 #define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0 #define TEMP_SENSOR_3 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
@ -301,35 +301,21 @@ your extruder heater takes 2 minutes to hit the target on heating.
// Enable this option for Toshiba steppers // Enable this option for Toshiba steppers
// #define CONFIG_STEPPERS_TOSHIBA // #define CONFIG_STEPPERS_TOSHIBA
// coarse Endstop Settings // The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
#ifndef ENDSTOPPULLUPS #define ENDSTOPPULLUP_ZMAX
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_XMAX #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_ZMIN
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
// #define ENDSTOPPULLUP_YMIN const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
// #define ENDSTOPPULLUP_ZMIN const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
#endif const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
#ifdef ENDSTOPPULLUPS const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
#define ENDSTOPPULLUP_XMAX const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN
#endif
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
//#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS
@ -346,13 +332,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define DISABLE_E false // For all extruders #define DISABLE_E false // For all extruders
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true // If you motor turns to wrong direction, you can invert it here:
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_X_DIR false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR false
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_Z_DIR false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E0_DIR false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false
#define INVERT_E3_DIR false
// ENDSTOP SETTINGS: // ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN // Sets direction of endstops when homing; 1=MAX, -1=MIN
@ -364,9 +351,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
#define X_MAX_POS 205 #define X_MAX_POS 200
#define X_MIN_POS 0 #define X_MIN_POS 0
#define Y_MAX_POS 205 #define Y_MAX_POS 200
#define Y_MIN_POS 0 #define Y_MIN_POS 0
#define Z_MAX_POS 200 #define Z_MAX_POS 200
#define Z_MIN_POS 0 #define Z_MIN_POS 0
@ -443,7 +430,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. // #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
//Useful to retract a deployable probe. //Useful to retract a deployable probe.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
@ -493,9 +480,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// default settings // default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker #define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
@ -539,11 +526,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// Preheat Constants // Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180 #define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70 #define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 #define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240 #define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100 #define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 #define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
//==============================LCD and SD support============================= //==============================LCD and SD support=============================

Write Preview
Loading…
Cancel
Save