andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Update BIQU SKR V1.1 pins, add TMC2130 settings (#13166) 

* Remove untested displays add TMC2130 configs.
* Remove references to the ReARM, delete untested displays. Add TMC2130 settings. Cleanup spacing, etc.
pull/1/head
Andy Shaw 6 years ago
committed by Scott Lahteine
parent
ab2816c870
commit
84fc400aba
1 changed files with 161 additions and 122 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Unified View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 259
      Marlin/src/pins/pins_BIQU_SKR_V1.1.h

259
Marlin/src/pins/pins_BIQU_SKR_V1.1.h
View File

@ -65,9 +65,9 @@
// Temperature Sensors // Temperature Sensors
// 3.3V max when defined as an analog input // 3.3V max when defined as an analog input
// //
#define TEMP_BED_PIN 0 // A0 (T0) - (67) - TEMP_BED_PIN #define TEMP_BED_PIN 0 // Analog Input
#define TEMP_0_PIN 1 // A1 (T1) - (68) - TEMP_0_PIN #define TEMP_0_PIN 1 // Analog Input
#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN #define TEMP_1_PIN 2 // Analog Input
// //
// Heaters / Fans // Heaters / Fans
@ -81,123 +81,34 @@
#define FAN_PIN P2_03 #define FAN_PIN P2_03
#define HEATER_BED_PIN P2_05 #define HEATER_BED_PIN P2_05
//
// Misc. Functions
//
#define SDSS P1_23 // (53)
/** /**
* LCD / Controller * LCD / Controller
* *
* All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required. * As of 20 JAN 2019 only the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER display has
*/ * been tested with these settings. It can be connected to the SKR using standard cables
* via the EXP1 and EXP2 ports. Other displays may need a custom cable and/or changes to
/** * the pins defined below.
* Smart LCD adapter
*
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
* is needed to pick up 5V for the EXP1 connection.
* *
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines * The SD card on the LCD controller uses the same SPI signals as the LCD, resulting in
* on the LCD display during accesses of the SD card. The menus/code has been arranged so * garbage/lines on the LCD display during SD card access. The LCD code mitigates this
* that the garbage/lines are erased immediately after the SD card accesses are completed. * by redrawing the screen after SD card accesses.
*/ */
#if ENABLED(ULTRA_LCD) #if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_30
#if ENABLED(CR10_STOCKDISPLAY) #define BTN_EN1 P3_26
#define BTN_EN2 P3_25
// Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. #define BTN_ENC P2_11
// Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one
// 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. #define SD_DETECT_PIN P1_31
// Requires REVERSE_ENCODER_DIRECTION in Configuration.h #define LCD_SDSS P1_23
#define LCD_PINS_RS P0_16
#define BEEPER_PIN P2_11 // J3-3 & AUX-4 #define LCD_PINS_ENABLE P0_18
#define LCD_PINS_D4 P0_15
#define BTN_EN1 P0_16 // J3-7 & AUX-4
#define BTN_EN2 P1_23 // J3-5 & AUX-4
#define BTN_ENC P3_25 // J3-4 & AUX-4
#define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS)
#define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI)
#define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK)
#else
#define BEEPER_PIN P1_30 // (37) not 5V tolerant
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
#if ENABLED(REPRAPWORLD_KEYPAD)
#define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
#define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
#define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#elif DISABLED(NEWPANEL)
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
#endif
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
// #define LCD_SCREEN_ROT_180
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define DOGLCD_CS P0_16 // (16)
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
#define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN
#define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes
#define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
#else
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
#define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers
#define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
#define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 P1_17 // (71) ENET_MDIO
#define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER
#define LCD_PINS_D7 P1_10 // (75) ENET_RXD1
#endif
#endif
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS
#if ENABLED(MINIPANEL)
// GLCD features
//#define LCD_CONTRAST 190
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#endif
#endif #endif
#endif // ULTRA_LCD
// //
// SD Support (as with the AZTEEG_X5_MINI_WIFI) // SD Support
// //
//#define USB_SD_DISABLED // Disable host access to SD card as mass storage device through USB //#define USB_SD_DISABLED // Disable host access to SD card as mass storage device through USB
#define USB_SD_ONBOARD // Enable host access to SD card as mass storage device through USB #define USB_SD_ONBOARD // Enable host access to SD card as mass storage device through USB
@ -230,3 +141,131 @@
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#endif #endif
// Trinamic driver support
#if HAS_TRINAMIC
// Using TMC devices in intelligent mode requires extra connections to each device. Unfortunately
// the SKR does not have many free pins (especially if a display is in use). The SPI-based devices
// will require 3 connections (clock, mosi, miso), plus a chip select line (CS) for each driver.
// The UART-based devices require 2 pis per deriver (one of which must be interrupt capable).
// The same SPI pins can be shared with the display/SD card reader, meaning SPI-based devices are
// probably a good choice for this board.
//
// SOFTWARE_DRIVER_ENABLE is a good option. It uses SPI to control the driver enable and allows the
// hardware ENABLE pins for each driver to be repurposed as SPI chip select. To use this mode the
// driver modules will probably need to be modified, removing the pin used for the enable line from
// the module and wiring this connection directly to GND (as is the case for TMC2130).
// Using this option and sharing all of the SPI pins allows 5 TMC2130 drivers to be used along with
// a REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER without requiring the use of any extra pins.
//
// Other options will probably require the use of any free pins and the TFT serial port or a
// different type of display (like the TFT), using the pins normally used for the display and encoder.
// Unfortunately, tests show it's not possible to use endstop and thermistor pins for chip-select.
// Sample settings are provided below, but only some have been tested.
//
// Another option is to share the enable and chip-select pins when using SPI. Several users have
// reported that this works. However, it's unlikely that this configuration will allow SPI communi-
// cation with the device when the drivers are active, meaning that some of the more advanced TMC
// options may not be available.
// When using any TMC SPI-based drivers, software SPI is used
// because pins may be shared with the display or SD card.
#define TMC_USE_SW_SPI
#define TMC_SW_MOSI P0_18
#define TMC_SW_MISO P0_17
// To minimize pin usage use the same clock pin as the display/SD card reader. (May generate LCD noise.)
#define TMC_SW_SCK P0_15
// If pin 2_06 is unused, it can be used for the clock to avoid the LCD noise.
//#define TMC_SW_SCK P2_06
#if ENABLED(SOFTWARE_DRIVER_ENABLE)
// Software enable allows the enable pins to be repurposed as chip-select pins.
// Note: Requires the driver modules to be modified to always be enabled with the enable pin removed.
#if AXIS_DRIVER_TYPE_X(TMC2130)
#define X_CS_PIN P4_28
#undef X_ENABLE_PIN
#define X_ENABLE_PIN -1
#endif
#if AXIS_DRIVER_TYPE_Y(TMC2130)
#define Y_CS_PIN P2_00
#undef Y_ENABLE_PIN
#define Y_ENABLE_PIN -1
#endif
#if AXIS_DRIVER_TYPE_Z(TMC2130)
#define Z_CS_PIN P0_19
#undef Z_ENABLE_PIN
#define Z_ENABLE_PIN -1
#endif
#if AXIS_DRIVER_TYPE_E0(TMC2130)
#define E0_CS_PIN P2_12
#undef E0_ENABLE_PIN
#define E0_ENABLE_PIN -1
#endif
#if AXIS_DRIVER_TYPE_E1(TMC2130)
#define E1_CS_PIN P0_10
#undef E1_ENABLE_PIN
#define E1_ENABLE_PIN -1
#endif
#else // !SOFTWARE_DRIVER_ENABLE
// A chip-select pin is needed for each driver.
// EXAMPLES
// Example 1: No LCD attached or a TFT style display using the AUX header RX/TX pins.
// LPC_SD_LCD must not be enabled. Nothing should be connected to EXP1/EXP2.
//#define SKR_USE_LCD_PINS_FOR_CS
#if ENABLED(SKR_USE_LCD_PINS_FOR_CS)
#if ENABLED(LPC_SD_LCD)
#error "LPC_SD_LCD must not be enabled with SKR_USE_LCD_PINS_FOR_CS."
#endif
#define X_CS_PIN P1_23
#define Y_CS_PIN P3_26
#define Z_CS_PIN P2_11
#define E0_CS_PIN P3_25
#define E1_CS_PIN P1_31
#endif
// Example 2: A REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
// The SD card reader attached to the LCD (if present) can't be used because
// the pins will be in use. So LPC_SD_LCD must not be defined.
//#define SKR_USE_LCD_SD_CARD_PINS_FOR_CS
#if ENABLED(SKR_USE_LCD_SD_CARD_PINS_FOR_CS)
#if ENABLED(LPC_SD_LCD)
#error "LPC_SD_LCD must not be enabled with SKR_USE_LCD_SD_CARD_PINS_FOR_CS."
#endif
#define X_CS_PIN P0_02
#define Y_CS_PIN P0_03
#define Z_CS_PIN P2_06
// We use SD_DETECT_PIN for E0
#undef SD_DETECT_PIN
#define E0_CS_PIN P1_31
// We use LCD_SDSS pin for E1
#undef LCD_SDSS
#define LCD_SDSS -1
#define E1_CS_PIN P1_23
#endif
// Example 3: Use the driver enable pins for chip-select.
// Commands must not be sent to the drivers when enabled. So certain
// advanced features (like driver monitoring) will not be available.
//#define SKR_USE_ENABLE_CS
#if ENABLED(SKR_USE_ENABLE_FOR_CS)
#define X_CS_PIN X_ENABLE_PIN
#define Y_CS_PIN Y_ENABLE_PIN
#define Z_CS_PIN Z_ENABLE_PIN
#define E0_CS_PIN E0_ENABLE_PIN
#define E1_CS_PIN E1_ENABLE_PIN
#endif
#endif // SOFTWARE_DRIVER_ENABLE
#endif

Write Preview
Loading…
Cancel
Save