Always define temp sensor, heater pins for RUMBA

Marlin/pins_RUMBA.h

@@ -77,43 +77,36 @@
 #define PS_ON_PIN          45
 #define KILL_PIN           46
 
-#if TEMP_SENSOR_0 != 0
-  #define HEATER_0_PIN          2   // EXTRUDER 1
-  #if TEMP_SENSOR_0 == -1
-    #define TEMP_0_PIN          6   // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
-  #else
-    #define TEMP_0_PIN         15   // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
-  #endif
+#define HEATER_0_PIN        2   // EXTRUDER 1
+#define HEATER_1_PIN        3   // EXTRUDER 2
+#define HEATER_2_PIN        6   // EXTRUDER 3
+
+#if TEMP_SENSOR_0 == -1
+  #define TEMP_0_PIN        6   // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
+#else
+  #define TEMP_0_PIN       15   // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
 #endif
 
-#if TEMP_SENSOR_1 != 0
-  #define HEATER_1_PIN          3   // EXTRUDER 2
-  #if TEMP_SENSOR_1 == -1
-    #define TEMP_1_PIN          5   // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
-  #else
-    #define TEMP_1_PIN         14   // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
-  #endif
+#if TEMP_SENSOR_1 == -1
+  #define TEMP_1_PIN        5   // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
+#else
+  #define TEMP_1_PIN       14   // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
 #endif
 
-#if TEMP_SENSOR_2 != 0
-  #define HEATER_2_PIN         6    // EXTRUDER 3
-  #if TEMP_SENSOR_2 == -1
-    #define TEMP_2_PIN         7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
-  #else
-    #define TEMP_2_PIN         13   // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used
-  #endif
+#if TEMP_SENSOR_2 == -1
+  #define TEMP_2_PIN        7   // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
+#else
+  #define TEMP_2_PIN       13   // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used
 #endif
 
 //optional for extruder 4 or chamber: #define TEMP_X_PIN         12   // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used
 //optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN       8    // EXTRUDER 4
 
-#if TEMP_SENSOR_BED != 0
-  #define HEATER_BED_PIN       9    // BED
-  #if TEMP_SENSOR_BED == -1
-    #define TEMP_BED_PIN       7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
-  #else
-    #define TEMP_BED_PIN      11    // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
-  #endif
+#define HEATER_BED_PIN      9    // BED
+#if TEMP_SENSOR_BED == -1
+  #define TEMP_BED_PIN      7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
+#else
+  #define TEMP_BED_PIN     11    // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
 #endif
 
 #define SDSS               53