Browse Source

Adjust some names and types in Marlin_main.cpp

pull/1/head
Scott Lahteine 10 years ago
parent
commit
7dfb8becdb
  1. 14
      Marlin/Marlin_main.cpp

14
Marlin/Marlin_main.cpp

@ -997,7 +997,7 @@ XYZ_CONSTS_FROM_CONFIG(signed char, home_dir, HOME_DIR);
#endif //DUAL_X_CARRIAGE #endif //DUAL_X_CARRIAGE
static void axis_is_at_home(int axis) { static void axis_is_at_home(AxisEnum axis) {
#ifdef DUAL_X_CARRIAGE #ifdef DUAL_X_CARRIAGE
if (axis == X_AXIS) { if (axis == X_AXIS) {
@ -1422,27 +1422,27 @@ static void setup_for_endstop_move() {
}; };
// Probe bed height at position (x,y), returns the measured z value // Probe bed height at position (x,y), returns the measured z value
static float probe_pt(float x, float y, float z_before, ProbeAction retract_action=ProbeDeployAndStow, int verbose_level=1) { static float probe_pt(float x, float y, float z_before, ProbeAction probe_action=ProbeDeployAndStow, int verbose_level=1) {
// move to right place // move to right place
do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], z_before); // this also updates current_position do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], z_before); // this also updates current_position
do_blocking_move_to(x - X_PROBE_OFFSET_FROM_EXTRUDER, y - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]); // this also updates current_position do_blocking_move_to(x - X_PROBE_OFFSET_FROM_EXTRUDER, y - Y_PROBE_OFFSET_FROM_EXTRUDER, current_position[Z_AXIS]); // this also updates current_position
#if !defined(Z_PROBE_SLED) && !defined(Z_PROBE_ALLEN_KEY) #if !defined(Z_PROBE_SLED) && !defined(Z_PROBE_ALLEN_KEY)
if (retract_action & ProbeDeploy) deploy_z_probe(); if (probe_action & ProbeDeploy) deploy_z_probe();
#endif #endif
run_z_probe(); run_z_probe();
float measured_z = current_position[Z_AXIS]; float measured_z = current_position[Z_AXIS];
#if Z_RAISE_BETWEEN_PROBINGS > 0 #if Z_RAISE_BETWEEN_PROBINGS > 0
if (retract_action == ProbeStay) { if (probe_action == ProbeStay) {
do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS); // this also updates current_position do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] + Z_RAISE_BETWEEN_PROBINGS); // this also updates current_position
st_synchronize(); st_synchronize();
} }
#endif #endif
#if !defined(Z_PROBE_SLED) && !defined(Z_PROBE_ALLEN_KEY) #if !defined(Z_PROBE_SLED) && !defined(Z_PROBE_ALLEN_KEY)
if (retract_action & ProbeStow) stow_z_probe(); if (probe_action & ProbeStow) stow_z_probe();
#endif #endif
if (verbose_level > 2) { if (verbose_level > 2) {
@ -5082,7 +5082,7 @@ inline void gcode_M999() {
* F[mm/min] Set the movement feedrate * F[mm/min] Set the movement feedrate
*/ */
inline void gcode_T() { inline void gcode_T() {
int tmp_extruder = code_value(); uint16_t tmp_extruder = code_value_short();
if (tmp_extruder >= EXTRUDERS) { if (tmp_extruder >= EXTRUDERS) {
SERIAL_ECHO_START; SERIAL_ECHO_START;
SERIAL_CHAR('T'); SERIAL_CHAR('T');
@ -5595,7 +5595,7 @@ void process_next_command() {
gcode_M400(); gcode_M400();
break; break;
#if defined(ENABLE_AUTO_BED_LEVELING) && (defined(SERVO_ENDSTOPS) || defined(Z_PROBE_ALLEN_KEY)) && not defined(Z_PROBE_SLED) #if defined(ENABLE_AUTO_BED_LEVELING) && (defined(SERVO_ENDSTOPS) || defined(Z_PROBE_ALLEN_KEY)) && !defined(Z_PROBE_SLED)
case 401: case 401:
gcode_M401(); gcode_M401();
break; break;

Loading…
Cancel
Save