Cleanup configurations

Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h

@@ -293,6 +293,7 @@
 #define HEATER_1_MAXTEMP 245
 #define HEATER_2_MAXTEMP 245
 #define HEATER_3_MAXTEMP 245
+#define HEATER_4_MAXTEMP 245
 #define BED_MAXTEMP 115
 
 //===========================================================================
@@ -322,6 +323,11 @@
   #define  DEFAULT_Ki 0.50
   #define  DEFAULT_Kd 60.00
 
+  // Ultimaker
+  //#define  DEFAULT_Kp 22.2
+  //#define  DEFAULT_Ki 1.08
+  //#define  DEFAULT_Kd 114
+
   // MakerGear
   //#define  DEFAULT_Kp 7.0
   //#define  DEFAULT_Ki 0.1
@@ -562,7 +568,6 @@
  */
 //#define FIX_MOUNTED_PROBE
 
-
 /**
  *   Z Servo Probe, such as an endstop switch on a rotating arm.
  *   NUM_SERVOS also needs to be set.  This is found later in this file.  Set it to
@@ -630,8 +635,10 @@
 #define XY_PROBE_SPEED 7500
 // Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
 // Speed for the "accurate" probe of each point
 #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
 // Use double touch for probing
 //#define PROBE_DOUBLE_TOUCH
 
@@ -693,7 +700,6 @@
  */
 
 //#define Z_MIN_PROBE_ENDSTOP
-
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 
 // Enable Z Probe Repeatability test to see how accurate your probe is
@@ -770,7 +776,6 @@
 #define Y_HOME_DIR -1
 #define Z_HOME_DIR -1
 
-
 // @section machine
 
 // Travel limits after homing (units are in mm)
@@ -803,7 +808,6 @@
 //===========================================================================
 //=============================== Bed Leveling ==============================
 //===========================================================================
-
 // @section bedlevel
 
 /**
@@ -850,7 +854,6 @@
 #define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
-
 /**
  * Enable detailed logging of G28, G29, M48, etc.
  * Turn on with the command 'M111 S32'.
@@ -901,7 +904,6 @@
 
   // 3 arbitrary points to probe.
   // A simple cross-product is used to estimate the plane of the bed.
-
   #define ABL_PROBE_PT_1_X 39
   #define ABL_PROBE_PT_1_Y 170
   #define ABL_PROBE_PT_2_X 39
@@ -927,6 +929,7 @@
   #define UBL_PROBE_PT_3_X 180
   #define UBL_PROBE_PT_3_Y 25
   #define UBL_G26_MESH_EDITING    // Enable G26 mesh editing
+
 #elif ENABLED(MESH_BED_LEVELING)
 
   //===========================================================================
@@ -1606,7 +1609,7 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)

Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h

@@ -419,7 +419,6 @@
  *    M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  */
 //#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
-
 //#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
 //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
 
@@ -587,10 +586,9 @@
  */
 #define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  #define BABYSTEP_XY  //not only z, but also XY in the menu. more clutter, more functions
-                       //not implemented for deltabots!
-  #define BABYSTEP_INVERT_Z false  //true for inverse movements in Z
-  #define BABYSTEP_MULTIPLICATOR 2 //faster movements
+  #define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 2 // Babysteps are very small. Increase for faster motion.
   //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
@@ -1034,7 +1032,6 @@
  * (https://github.com/ameyer/Arduino-L6470)
  */
 
-
 //#define HAVE_L6470DRIVER
 #if ENABLED(HAVE_L6470DRIVER)
 
@@ -1155,7 +1152,6 @@
  */
 //#define EXTENDED_CAPABILITIES_REPORT
 
-
 /**
  * Volumetric extrusion default state
  * Activate to make volumetric extrusion the default method,

Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h

@@ -474,7 +474,7 @@
 #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
 
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
@@ -730,8 +730,6 @@
 #define Z_CLEARANCE_DEPLOY_PROBE   15 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  6 // Z Clearance between probe points
 
-//
-
 // For M851 give a range for adjusting the Z probe offset
 #define Z_PROBE_OFFSET_RANGE_MIN -20
 #define Z_PROBE_OFFSET_RANGE_MAX 20
@@ -1035,7 +1033,7 @@
 //
 // M100 Free Memory Watcher
 //
-#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
+//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
 
 //
 // G20/G21 Inch mode support
@@ -1619,7 +1617,7 @@
  */
 //#define FILAMENT_WIDTH_SENSOR
 
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75   // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
   #define FILAMENT_SENSOR_EXTRUDER_NUM 0    // Index of the extruder that has the filament sensor (0,1,2,3)
@@ -1633,6 +1631,6 @@
 
   // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
   //#define FILAMENT_LCD_DISPLAY
-#endif //FILAMENT_WIDTH_SENSOR
+#endif
 
 #endif // CONFIGURATION_H

Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h

@@ -361,7 +361,7 @@
 // Default stepper release if idle. Set to 0 to deactivate.
 // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
 // Time can be set by M18 and M84.
-#define DEFAULT_STEPPER_DEACTIVE_TIME 0    // usually is set to 120 seconds
+#define DEFAULT_STEPPER_DEACTIVE_TIME 0    // usually set to 120 seconds
 #define DISABLE_INACTIVE_X true
 #define DISABLE_INACTIVE_Y true
 #define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.

Marlin/example_configurations/gCreate_gMax1.5+/_Bootscreen.h

@@ -106,5 +106,3 @@ const unsigned char custom_start_bmp[896] PROGMEM = {
   0x03, 0x80, 0x00, 0x20, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01,
   0x01, 0xff, 0xff, 0xff, 0xe0, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
 };
-
-