andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Merge pull request #5981 from thinkyhead/rc_tmc2130_redo 

TMC2130 Library: @teemuatlut replaces @makertum
pull/1/head
Scott Lahteine 8 years ago
committed by GitHub
parent
33f8a8a344 5a456c832a
commit
7c9e2e2a1a
25 changed files with 1991 additions and 3851 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 8
      .travis.yml
  2. 273
      Marlin/Configuration_adv.h
  3. 4
      Marlin/Marlin.ino
  4. 236
      Marlin/Marlin_main.cpp
  5. 220
      Marlin/configuration_store.cpp
  6. 269
      Marlin/example_configurations/Cartesio/Configuration_adv.h
  7. 269
      Marlin/example_configurations/Felix/Configuration_adv.h
  8. 269
      Marlin/example_configurations/Hephestos/Configuration_adv.h
  9. 269
      Marlin/example_configurations/Hephestos_2/Configuration_adv.h
  10. 269
      Marlin/example_configurations/K8200/Configuration_adv.h
  11. 269
      Marlin/example_configurations/K8400/Configuration_adv.h
  12. 269
      Marlin/example_configurations/RigidBot/Configuration_adv.h
  13. 269
      Marlin/example_configurations/SCARA/Configuration_adv.h
  14. 269
      Marlin/example_configurations/TAZ4/Configuration_adv.h
  15. 269
      Marlin/example_configurations/WITBOX/Configuration_adv.h
  16. 269
      Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h
  17. 269
      Marlin/example_configurations/delta/generic/Configuration_adv.h
  18. 269
      Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
  19. 269
      Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
  20. 269
      Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
  21. 269
      Marlin/example_configurations/makibox/Configuration_adv.h
  22. 269
      Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
  23. 2
      Marlin/stepper.cpp
  24. 478
      Marlin/stepper_indirection.cpp
  25. 46
      Marlin/stepper_indirection.h

8
.travis.yml
View File

@ -47,8 +47,8 @@ install:
# - sudo mv TMC26XStepper /usr/local/share/arduino/libraries/TMC26XStepper
#
# Install: TMC2130 Stepper Motor Controller library
- git clone https://github.com/MarlinFirmware/Trinamic_TMC2130.git
- sudo mv Trinamic_TMC2130/Trinamic_TMC2130 /usr/local/share/arduino/libraries/Trinamic_TMC2130
- git clone https://github.com/teemuatlut/TMC2130Stepper.git
- sudo mv TMC2130Stepper /usr/local/share/arduino/libraries/TMC2130Stepper
#
before_script:
#
@ -396,7 +396,9 @@ script:
# TMC2130 Config
#
- restore_configs
- opt_enable_adv HAVE_TMC2130DRIVER X_IS_TMC2130 Y_IS_TMC2130 Z_IS_TMC2130 E0_IS_TMC2130
- opt_enable_adv HAVE_TMC2130 X_IS_TMC2130 Y_IS_TMC2130 Z_IS_TMC2130
- build_marlin
- opt_enable_adv AUTOMATIC_CURRENT_CONTROL STEALTHCHOP
- build_marlin
#
# tvrrug Config need to check board type for sanguino atmega644p

273
Marlin/Configuration_adv.h
View File

@ -761,14 +761,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -826,23 +827,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -856,182 +865,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
// @section L6470
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
/**
* Enable this section if you have L6470 motor drivers.
@ -1039,6 +934,8 @@
* (https://github.com/ameyer/Arduino-L6470)
*/
// @section l6470
//#define HAVE_L6470DRIVER
#if ENABLED(HAVE_L6470DRIVER)

4
Marlin/Marlin.ino
View File

@ -61,9 +61,9 @@
#include <TMC26XStepper.h>
#endif
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#include <SPI.h>
#include <Trinamic_TMC2130.h>
#include <TMC2130Stepper.h>
#endif
#if ENABLED(HAVE_L6470DRIVER)

236
Marlin/Marlin_main.cpp
View File

@ -189,10 +189,13 @@
* M666 - Set delta endstop adjustment. (Requires DELTA)
* M605 - Set dual x-carriage movement mode: "M605 S<mode> [X<x_offset>] [R<temp_offset>]". (Requires DUAL_X_CARRIAGE)
* M851 - Set Z probe's Z offset in current units. (Negative = below the nozzle.)
* M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. (Requires HAVE_TMC2130)
* M907 - Set digital trimpot motor current using axis codes. (Requires a board with digital trimpots)
* M908 - Control digital trimpot directly. (Requires DAC_STEPPER_CURRENT or DIGIPOTSS_PIN)
* M909 - Print digipot/DAC current value. (Requires DAC_STEPPER_CURRENT)
* M910 - Commit digipot/DAC value to external EEPROM via I2C. (Requires DAC_STEPPER_CURRENT)
* M911 - Report stepper driver overtemperature pre-warn condition. (Requires HAVE_TMC2130)
* M912 - Clear stepper driver overtemperature pre-warn condition flag. (Requires HAVE_TMC2130)
* M350 - Set microstepping mode. (Requires digital microstepping pins.)
* M351 - Toggle MS1 MS2 pins directly. (Requires digital microstepping pins.)
*
@ -6127,58 +6130,6 @@ inline void gcode_M120() { endstops.enable_globally(true); }
*/
inline void gcode_M121() { endstops.enable_globally(false); }
#if ENABLED(HAVE_TMC2130DRIVER)
/**
* M122: Output Trinamic TMC2130 status to serial output. Very bad formatting.
*/
static void tmc2130_report(Trinamic_TMC2130 &stepr, const char *name) {
stepr.read_STAT();
SERIAL_PROTOCOL(name);
SERIAL_PROTOCOL(": ");
stepr.isReset() ? SERIAL_PROTOCOLPGM("RESET ") : SERIAL_PROTOCOLPGM("----- ");
stepr.isError() ? SERIAL_PROTOCOLPGM("ERROR ") : SERIAL_PROTOCOLPGM("----- ");
stepr.isStallguard() ? SERIAL_PROTOCOLPGM("SLGRD ") : SERIAL_PROTOCOLPGM("----- ");
stepr.isStandstill() ? SERIAL_PROTOCOLPGM("STILL ") : SERIAL_PROTOCOLPGM("----- ");
SERIAL_PROTOCOLLN(stepr.debug());
}
inline void gcode_M122() {
SERIAL_PROTOCOLLNPGM("Reporting TMC2130 status");
#if ENABLED(X_IS_TMC2130)
tmc2130_report(stepperX, "X");
#endif
#if ENABLED(X2_IS_TMC2130)
tmc2130_report(stepperX2, "X2");
#endif
#if ENABLED(Y_IS_TMC2130)
tmc2130_report(stepperY, "Y");
#endif
#if ENABLED(Y2_IS_TMC2130)
tmc2130_report(stepperY2, "Y2");
#endif
#if ENABLED(Z_IS_TMC2130)
tmc2130_report(stepperZ, "Z");
#endif
#if ENABLED(Z2_IS_TMC2130)
tmc2130_report(stepperZ2, "Z2");
#endif
#if ENABLED(E0_IS_TMC2130)
tmc2130_report(stepperE0, "E0");
#endif
#if ENABLED(E1_IS_TMC2130)
tmc2130_report(stepperE1, "E1");
#endif
#if ENABLED(E2_IS_TMC2130)
tmc2130_report(stepperE2, "E2");
#endif
#if ENABLED(E3_IS_TMC2130)
tmc2130_report(stepperE3, "E3");
#endif
}
#endif // HAVE_TMC2130DRIVER
#if ENABLED(BLINKM) || ENABLED(RGB_LED)
void set_led_color(const uint8_t r, const uint8_t g, const uint8_t b) {
@ -7610,7 +7561,7 @@ inline void gcode_M503() {
SERIAL_ECHOLNPAIR(MSG_DUPLICATION_MODE, extruder_duplication_enabled ? MSG_ON : MSG_OFF);
}
#endif // M605
#endif // DUAL_NOZZLE_DUPLICATION_MODE
#if ENABLED(LIN_ADVANCE)
/**
@ -7637,7 +7588,99 @@ inline void gcode_M503() {
if (ratio) SERIAL_ECHOLN(ratio); else SERIAL_ECHOLNPGM("Automatic");
}
}
#endif
#endif // LIN_ADVANCE
#if ENABLED(HAVE_TMC2130)
static void tmc2130_print_current(const int mA, const char name) {
SERIAL_CHAR(name);
SERIAL_ECHOPGM(" axis driver current: ");
SERIAL_ECHOLN(mA);
}
static void tmc2130_set_current(const int mA, TMC2130Stepper &st, const char name) {
tmc2130_print_current(mA, name);
st.setCurrent(mA, 0.11, 0.5);
}
static void tmc2130_get_current(TMC2130Stepper &st, const char name) {
tmc2130_print_current(st.getCurrent(), name);
}
static void tmc2130_report_otpw(TMC2130Stepper &st, const char name) {
SERIAL_CHAR(name);
SERIAL_ECHOPGM(" axis temperature prewarn triggered: ");
serialprintPGM(st.getOTPW() ? PSTR("true") : PSTR("false"));
}
static void tmc2130_clear_otpw(TMC2130Stepper &st, const char name) {
st.clear_otpw();
SERIAL_CHAR(name);
SERIAL_ECHOLNPGM(" prewarn flag cleared");
}
/**
* M906: Set motor current in milliamps using axis codes X, Y, Z, E
*
* Report driver currents when no axis specified
*/
inline void gcode_M906() {
uint16_t values[NUM_AXIS];
LOOP_XYZE(i)
values[i] = code_seen(axis_codes[i]) ? code_value_int() : 0;
#if ENABLED(X_IS_TMC2130)
if (values[X_AXIS]) tmc2130_set_current(values[X_AXIS], stepperX, 'X');
else tmc2130_get_current(stepperX, 'X');
#endif
#if ENABLED(Y_IS_TMC2130)
if (values[Y_AXIS]) tmc2130_set_current(values[Y_AXIS], stepperY, 'Y');
else tmc2130_get_current(stepperY, 'Y');
#endif
#if ENABLED(Z_IS_TMC2130)
if (values[Z_AXIS]) tmc2130_set_current(values[Z_AXIS], stepperZ, 'Z');
else tmc2130_get_current(stepperZ, 'Z');
#endif
#if ENABLED(E0_IS_TMC2130)
if (values[E_AXIS]) tmc2130_set_current(values[E_AXIS], stepperE0, 'E');
else tmc2130_get_current(stepperE0, 'E');
#endif
}
/**
* M911: Report TMC2130 stepper driver overtemperature pre-warn flag
* The flag is held by the library and persist until manually cleared by M912
*/
inline void gcode_M911() {
#if ENABLED(X_IS_TMC2130)
tmc2130_report_otpw(stepperX, 'X');
#endif
#if ENABLED(Y_IS_TMC2130)
tmc2130_report_otpw(stepperY, 'Y');
#endif
#if ENABLED(Z_IS_TMC2130)
tmc2130_report_otpw(stepperZ, 'Z');
#endif
#if ENABLED(E0_IS_TMC2130)
tmc2130_report_otpw(stepperE0, 'E');
#endif
}
/**
* M912: Clear TMC2130 stepper driver overtemperature pre-warn flag held by the library
*/
inline void gcode_M912() {
#if ENABLED(X_IS_TMC2130)
if (code_seen('X')) tmc2130_clear_otpw(stepperX, 'X');
#endif
#if ENABLED(Y_IS_TMC2130)
if (code_seen('Y')) tmc2130_clear_otpw(stepperY, 'Y');
#endif
#if ENABLED(Z_IS_TMC2130)
if (code_seen('Z')) tmc2130_clear_otpw(stepperZ, 'Z');
#endif
#if ENABLED(E0_IS_TMC2130)
if (code_seen('E')) tmc2130_clear_otpw(stepperE0, 'E');
#endif
}
#endif // HAVE_TMC2130
/**
* M907: Set digital trimpot motor current using axis codes X, Y, Z, E, B, S
@ -8600,12 +8643,6 @@ void process_next_command() {
gcode_M121();
break;
#if ENABLED(HAVE_TMC2130DRIVER)
case 122: // M122: Diagnose, used to debug TMC2130
gcode_M122();
break;
#endif
#if ENABLED(ULTIPANEL)
case 145: // M145: Set material heatup parameters
@ -8882,6 +8919,12 @@ void process_next_command() {
break;
#endif
#if ENABLED(HAVE_TMC2130)
case 906: // M906: Set motor current in milliamps using axis codes X, Y, Z, E
gcode_M906();
break;
#endif
case 907: // M907: Set digital trimpot motor current using axis codes.
gcode_M907();
break;
@ -8906,6 +8949,16 @@ void process_next_command() {
#endif // HAS_DIGIPOTSS || DAC_STEPPER_CURRENT
#if ENABLED(HAVE_TMC2130)
case 911: // M911: Report TMC2130 prewarn triggered flags
gcode_M911();
break;
case 912: // M911: Clear TMC2130 prewarn triggered flags
gcode_M912();
break;
#endif
#if HAS_MICROSTEPS
case 350: // M350: Set microstepping mode. Warning: Steps per unit remains unchanged. S code sets stepping mode for all drivers.
@ -10169,6 +10222,65 @@ void disable_all_steppers() {
disable_e3();
}
#if ENABLED(AUTOMATIC_CURRENT_CONTROL)
void automatic_current_control(const TMC2130Stepper &st) {
#if CURRENT_STEP > 0
const bool is_otpw = st.checkOT(), // Check otpw even if we don't adjust. Allows for flag inspection.
is_otpw_triggered = st.getOTPW();
if (!is_otpw && !is_otpw_triggered) {
// OTPW bit not triggered yet -> Increase current
const uint16_t current = st.getCurrent() + CURRENT_STEP;
if (current <= AUTO_ADJUST_MAX) st.SilentStepStick2130(current);
}
else if (is_otpw && is_otpw_triggered) {
// OTPW bit triggered, triggered flag raised -> Decrease current
st.SilentStepStick2130((float)st.getCurrent() - CURRENT_STEP);
}
// OTPW bit cleared (we've cooled down), triggered flag still raised until manually cleared -> Do nothing, we're good
#endif
}
void checkOverTemp() {
static millis_t next_cOT = 0;
if (ELAPSED(millis(), next_cOT)) {
next_cOT = millis() + 5000;
#if ENABLED(X_IS_TMC2130)
automatic_current_control(stepperX);
#endif
#if ENABLED(Y_IS_TMC2130)
automatic_current_control(stepperY);
#endif
#if ENABLED(Z_IS_TMC2130)
automatic_current_control(stepperZ);
#endif
#if ENABLED(X2_IS_TMC2130)
automatic_current_control(stepperX2);
#endif
#if ENABLED(Y2_IS_TMC2130)
automatic_current_control(stepperY2);
#endif
#if ENABLED(Z2_IS_TMC2130)
automatic_current_control(stepperZ2);
#endif
#if ENABLED(E0_IS_TMC2130)
automatic_current_control(stepperE0);
#endif
#if ENABLED(E1_IS_TMC2130)
automatic_current_control(stepperE1);
#endif
#if ENABLED(E2_IS_TMC2130)
automatic_current_control(stepperE2);
#endif
#if ENABLED(E3_IS_TMC2130)
automatic_current_control(stepperE3);
#endif
}
}
#endif // AUTOMATIC_CURRENT_CONTROL
/**
* Manage several activities:
* - Check for Filament Runout
@ -10360,6 +10472,10 @@ void manage_inactivity(bool ignore_stepper_queue/*=false*/) {
handle_status_leds();
#endif
#if ENABLED(AUTOMATIC_CURRENT_CONTROL)
checkOverTemp();
#endif
planner.check_axes_activity();
}

220
Marlin/configuration_store.cpp
View File

@ -36,13 +36,13 @@
*
*/
#define EEPROM_VERSION "V29"
#define EEPROM_VERSION "V30"
// Change EEPROM version if these are changed:
#define EEPROM_OFFSET 100
/**
* V29 EEPROM Layout:
* V30 EEPROM Layout:
*
* 100 Version (char x4)
* 104 EEPROM Checksum (uint16_t)
@ -128,8 +128,20 @@
* 509 M200 D volumetric_enabled (bool)
* 510 M200 T D filament_size (float x4) (T0..3)
*
* 526 Minimum end-point
* 1847 (526 + 36 + 9 + 288 + 988) Maximum end-point
* TMC2130: 20 bytes
* 526 M906 X TMC2130 X-stepper current (uint16_t)
* 528 M906 Y TMC2130 Y-stepper current (uint16_t)
* 530 M906 Z TMC2130 Z-stepper current (uint16_t)
* 532 M906 X2 TMC2130 X2-stepper current (uint16_t)
* 534 M906 Y2 TMC2130 Y2-stepper current (uint16_t)
* 536 M906 Z2 TMC2130 Z2-stepper current (uint16_t)
* 538 M906 E0 TMC2130 E0-stepper current (uint16_t)
* 540 M906 E1 TMC2130 E1-stepper current (uint16_t)
* 542 M906 E2 TMC2130 E2-stepper current (uint16_t)
* 544 M906 E3 TMC2130 E3-stepper current (uint16_t)
*
* 546 Minimum end-point
* 1867 (546 + 36 + 9 + 288 + 988) Maximum end-point
*
*/
#include "Marlin.h"
@ -144,6 +156,10 @@
#include "mesh_bed_leveling.h"
#endif
#if ENABLED(HAVE_TMC2130)
#include "stepper_indirection.h"
#endif
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
extern void bed_level_virt_interpolate();
#endif
@ -432,9 +448,77 @@ void Config_Postprocess() {
EEPROM_WRITE(dummy);
}
// Save TCM2130 Configuration, and placeholder values
uint16_t val;
#if ENABLED(HAVE_TMC2130)
#if ENABLED(X_IS_TMC2130)
val = stepperX.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(Y_IS_TMC2130)
val = stepperY.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(Z_IS_TMC2130)
val = stepperZ.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(X2_IS_TMC2130)
val = stepperX2.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(Y2_IS_TMC2130)
val = stepperY2.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(Z2_IS_TMC2130)
val = stepperZ2.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(E0_IS_TMC2130)
val = stepperE0.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(E1_IS_TMC2130)
val = stepperE1.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(E2_IS_TMC2130)
val = stepperE2.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#if ENABLED(E3_IS_TMC2130)
val = stepperE3.getCurrent();
#else
val = 0;
#endif
EEPROM_WRITE(val);
#else
val = 0;
for (uint8_t q = 0; q < 10; ++q) EEPROM_WRITE(val);
#endif
if (!eeprom_write_error) {
uint16_t final_checksum = eeprom_checksum,
const uint16_t final_checksum = eeprom_checksum,
eeprom_size = eeprom_index;
// Write the EEPROM header
@ -684,6 +768,52 @@ void Config_Postprocess() {
if (q < COUNT(filament_size)) filament_size[q] = dummy;
}
uint16_t val;
#if ENABLED(HAVE_TMC2130)
EEPROM_READ(val);
#if ENABLED(X_IS_TMC2130)
stepperX.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(Y_IS_TMC2130)
stepperY.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(Z_IS_TMC2130)
stepperZ.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(X2_IS_TMC2130)
stepperX2.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(Y2_IS_TMC2130)
stepperY2.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(Z2_IS_TMC2130)
stepperZ2.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(E0_IS_TMC2130)
stepperE0.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(E1_IS_TMC2130)
stepperE1.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(E2_IS_TMC2130)
stepperE2.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
EEPROM_READ(val);
#if ENABLED(E3_IS_TMC2130)
stepperE3.setCurrent(val, R_SENSE, HOLD_MULTIPLIER);
#endif
#else
for (uint8_t q = 0; q < 10; q++) EEPROM_READ(val);
#endif
if (eeprom_checksum == stored_checksum) {
if (eeprom_read_error)
Config_ResetDefault();
@ -852,6 +982,39 @@ void Config_ResetDefault() {
#endif
);
#if ENABLED(HAVE_TMC2130)
#if ENABLED(X_IS_TMC2130)
stepperX.setCurrent(X_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(Y_IS_TMC2130)
stepperY.setCurrent(Y_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(Z_IS_TMC2130)
stepperZ.setCurrent(Z_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(X2_IS_TMC2130)
stepperX2.setCurrent(X2_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(Y2_IS_TMC2130)
stepperY2.setCurrent(Y2_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(Z2_IS_TMC2130)
stepperZ2.setCurrent(Z2_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(E0_IS_TMC2130)
stepperE0.setCurrent(E0_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(E1_IS_TMC2130)
stepperE1.setCurrent(E1_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(E2_IS_TMC2130)
stepperE2.setCurrent(E2_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#if ENABLED(E3_IS_TMC2130)
stepperE3.setCurrent(E3_MAX_CURRENT, R_SENSE, HOLD_MULTIPLIER);
#endif
#endif
Config_Postprocess();
SERIAL_ECHO_START;
@ -1184,14 +1347,57 @@ void Config_ResetDefault() {
* Auto Bed Leveling
*/
#if HAS_BED_PROBE
if (!forReplay) {
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Z-Probe Offset (mm):");
}
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M851 Z", zprobe_zoffset);
SERIAL_EOL;
#endif
/**
* TMC2130 stepper driver current
*/
#if ENABLED(HAVE_TMC2130)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Stepper driver current:");
CONFIG_ECHO_START;
}
SERIAL_ECHO(" M906");
#if ENABLED(X_IS_TMC2130)
SERIAL_ECHOPAIR(" X", stepperX.getCurrent());
#endif
#if ENABLED(Y_IS_TMC2130)
SERIAL_ECHOPAIR(" Y", stepperY.getCurrent());
#endif
#if ENABLED(Z_IS_TMC2130)
SERIAL_ECHOPAIR(" Z", stepperZ.getCurrent());
#endif
#if ENABLED(X2_IS_TMC2130)
SERIAL_ECHOPAIR(" X2", stepperX2.getCurrent());
#endif
#if ENABLED(Y2_IS_TMC2130)
SERIAL_ECHOPAIR(" Y2", stepperY2.getCurrent());
#endif
#if ENABLED(Z2_IS_TMC2130)
SERIAL_ECHOPAIR(" Z2", stepperZ2.getCurrent());
#endif
#if ENABLED(E0_IS_TMC2130)
SERIAL_ECHOPAIR(" E0", stepperE0.getCurrent());
#endif
#if ENABLED(E1_IS_TMC2130)
SERIAL_ECHOPAIR(" E1", stepperE1.getCurrent());
#endif
#if ENABLED(E2_IS_TMC2130)
SERIAL_ECHOPAIR(" E2", stepperE2.getCurrent());
#endif
#if ENABLED(E3_IS_TMC2130)
SERIAL_ECHOPAIR(" E3", stepperE3.getCurrent());
#endif
SERIAL_EOL;
#endif
}
#endif // !DISABLE_M503

269
Marlin/example_configurations/Cartesio/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/Felix/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/Hephestos/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/Hephestos_2/Configuration_adv.h
View File

@ -741,14 +741,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -806,23 +807,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -836,180 +845,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/K8200/Configuration_adv.h
View File

@ -771,14 +771,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -836,23 +837,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -866,180 +875,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/K8400/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/RigidBot/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/SCARA/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/TAZ4/Configuration_adv.h
View File

@ -766,14 +766,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -831,23 +832,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -861,180 +870,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/WITBOX/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/delta/flsun_kossel_mini/Configuration_adv.h
View File

@ -763,14 +763,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -828,23 +829,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -858,180 +867,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/delta/generic/Configuration_adv.h
View File

@ -760,14 +760,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -825,23 +826,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -855,180 +864,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
View File

@ -760,14 +760,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -825,23 +826,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -855,180 +864,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
View File

@ -765,14 +765,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -830,23 +831,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -860,180 +869,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
View File

@ -760,14 +760,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -825,23 +826,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -855,180 +864,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/makibox/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

269
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
View File

@ -758,14 +758,15 @@
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
#endif
/******************************************************************************\
* enable this section if you have TMC26X motor drivers.
* you need to import the TMC26XStepper library into the Arduino IDE for this
******************************************************************************/
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers.
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* (https://github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
#if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
@ -823,23 +824,31 @@
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
*
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
* (https://github.com/makertum/Trinamic_TMC2130).
* You'll also need the TMC2130Stepper Arduino library
* (https://github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
*/
//#define HAVE_TMC2130
//#define HAVE_TMC2130DRIVER
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#define STEALTHCHOP
//#define TMC2130_ADVANCED_CONFIGURATION
/**
* Let Marlin automatically control stepper current.
* This is still an experimental feature.
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
*/
//#define AUTOMATIC_CURRENT_CONTROL
#define CURRENT_STEP 50 // [mA]
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
@ -853,180 +862,68 @@
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
// Enabled settings will be automatically applied to all axes specified above.
//
// Please read the TMC2130 datasheet:
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
// All settings here have the same (sometimes cryptic) names as in the datasheet.
//
// The following, uncommented settings are only suggestion.
/* GENERAL CONFIGURATION */
//#define GLOBAL_EN_PWM_MODE 0
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
/* VELOCITY-DEPENDENT DRIVE FEATURES */
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
/* SPI MODE CONFIGURATION */
//#define GLOBAL_XDIRECT 0
/* DCSTEP MINIMUM VELOCITY */
//#define GLOBAL_VDCMIN 0
/* MOTOR DRIVER CONFIGURATION*/
//#define GLOBAL_DEDGE 0
//#define GLOBAL_DISS2G 0
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
#define GLOBAL_MRES 16 // number of microsteps
#define GLOBAL_SYNC 1 // [0-15]
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
//#define GLOBAL_RNDTF 0
//#define GLOBAL_DISFDCC 0
//#define GLOBAL_FD 0
//#define GLOBAL_HEND 0
//#define GLOBAL_HSTRT 0
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
//#define GLOBAL_SFILT 0
//#define GLOBAL_SGT 0
//#define GLOBAL_SEIMIN 0
//#define GLOBAL_SEDN 0
//#define GLOBAL_SEMAX 0
//#define GLOBAL_SEUP 0
//#define GLOBAL_SEMIN 0
//#define GLOBAL_DC_TIME 0
//#define GLOBAL_DC_SG 0
//#define GLOBAL_FREEWHEEL 0
//#define GLOBAL_PWM_SYMMETRIC 0
//#define GLOBAL_PWM_AUTOSCALE 0
//#define GLOBAL_PWM_FREQ 0
//#define GLOBAL_PWM_GRAD 0
//#define GLOBAL_PWM_AMPL 0
//#define GLOBAL_ENCM_CTRL 0
#else
#define X_IHOLD 31 // [0-31] 0: min, 31: max
#define X_IRUN 31 // [0-31] 0: min, 31: max
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
#define X_MRES 16 // number of microsteps
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
#define X2_IHOLD 31
#define X2_IRUN 31
#define X2_IHOLDDELAY 15
#define X2_I_SCALE_ANALOG 1
#define X2_MRES 16
#define X2_TBL 1
#define X2_TOFF 8
#define Y_IHOLD 31
#define Y_IRUN 31
#define Y_IHOLDDELAY 15
#define Y_I_SCALE_ANALOG 1
#define Y_MRES 16
#define Y_TBL 1
#define Y_TOFF 8
#define Y2_IHOLD 31
#define Y2_IRUN 31
#define Y2_IHOLDDELAY 15
#define Y2_I_SCALE_ANALOG 1
#define Y2_MRES 16
#define Y2_TBL 1
#define Y2_TOFF 8
#define Z_IHOLD 31
#define Z_IRUN 31
#define Z_IHOLDDELAY 15
#define Z_I_SCALE_ANALOG 1
#define Z_MRES 16
#define Z_TBL 1
#define Z_TOFF 8
#define Z2_IHOLD 31
#define Z2_IRUN 31
#define Z2_IHOLDDELAY 15
#define Z2_I_SCALE_ANALOG 1
#define Z2_MRES 16
#define Z2_TBL 1
#define Z2_TOFF 8
#define E0_IHOLD 31
#define E0_IRUN 31
#define E0_IHOLDDELAY 15
#define E0_I_SCALE_ANALOG 1
#define E0_MRES 16
#define E0_TBL 1
#define E0_TOFF 8
#define E1_IHOLD 31
#define E1_IRUN 31
#define E1_IHOLDDELAY 15
#define E1_I_SCALE_ANALOG 1
#define E1_MRES 16
#define E1_TBL 1
#define E1_TOFF 8
#define E2_IHOLD 31
#define E2_IRUN 31
#define E2_IHOLDDELAY 15
#define E2_I_SCALE_ANALOG 1
#define E2_MRES 16
#define E2_TBL 1
#define E2_TOFF 8
#define E3_IHOLD 31
#define E3_IRUN 31
#define E3_IHOLDDELAY 15
#define E3_I_SCALE_ANALOG 1
#define E3_MRES 16
#define E3_TBL 1
#define E3_TOFF 8
#endif // TMC2130_ADVANCED_CONFIGURATION
#endif // HAVE_TMC2130DRIVER
/**
* Stepper driver settings
*/
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
#define X_MAX_CURRENT 1000 // rms current in mA
#define X_MICROSTEPS 16 // FULLSTEP..256
#define X_CHIP_SELECT 40 // Pin
#define Y_MAX_CURRENT 1000
#define Y_MICROSTEPS 16
#define Y_CHIP_SELECT 42
#define Z_MAX_CURRENT 1000
#define Z_MICROSTEPS 16
#define Z_CHIP_SELECT 65
//#define X2_MAX_CURRENT 1000
//#define X2_MICROSTEPS 16
//#define X2_CHIP_SELECT -1
//#define Y2_MAX_CURRENT 1000
//#define Y2_MICROSTEPS 16
//#define Y2_CHIP_SELECT -1
//#define Z2_MAX_CURRENT 1000
//#define Z2_MICROSTEPS 16
//#define Z2_CHIP_SELECT -1
//#define E0_MAX_CURRENT 1000
//#define E0_MICROSTEPS 16
//#define E0_CHIP_SELECT -1
//#define E1_MAX_CURRENT 1000
//#define E1_MICROSTEPS 16
//#define E1_CHIP_SELECT -1
//#define E2_MAX_CURRENT 1000
//#define E2_MICROSTEPS 16
//#define E2_CHIP_SELECT -1
//#define E3_MAX_CURRENT 1000
//#define E3_MICROSTEPS 16
//#define E3_CHIP_SELECT -1
/**
* You can set your own advanced settings by filling in predefined functions.
* A list of available functions can be found on the library github page
* https://github.com/teemuatlut/TMC2130Stepper
*
* Example:
* #define TMC2130_ADV() { \
* stepperX.diag0_temp_prewarn(1); \
* stepperX.interpolate(0); \
* }
*/
#define TMC2130_ADV() { }
#endif // ENABLED(HAVE_TMC2130)
// @section L6470

2
Marlin/stepper.cpp
View File

@ -894,7 +894,7 @@ void Stepper::init() {
#endif
// Init TMC2130 Steppers
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
tmc2130_init();
#endif

478
Marlin/stepper_indirection.cpp
View File

@ -21,25 +21,15 @@
*/
/**
stepper_indirection.c - stepper motor driver indirection
to allow some stepper functions to be done via SPI/I2c instead of direct pin manipulation
Part of Marlin
Copyright (c) 2015 Dominik Wenger
Marlin is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Marlin is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Marlin. If not, see <http://www.gnu.org/licenses/>.
*/
* stepper_indirection.cpp
*
* Stepper motor driver indirection to allow some stepper functions to
* be done via SPI/I2c instead of direct pin manipulation.
*
* Part of Marlin
*
* Copyright (c) 2015 Dominik Wenger
*/
#include "stepper_indirection.h"
@ -53,41 +43,43 @@
#include <SPI.h>
#include <TMC26XStepper.h>
#define _TMC_DEFINE(ST) TMC26XStepper stepper##ST(200, ST##_ENABLE_PIN, ST##_STEP_PIN, ST##_DIR_PIN, ST##_MAX_CURRENT, ST##_SENSE_RESISTOR)
#if ENABLED(X_IS_TMC)
TMC26XStepper stepperX(200, X_ENABLE_PIN, X_STEP_PIN, X_DIR_PIN, X_MAX_CURRENT, X_SENSE_RESISTOR);
_TMC_DEFINE(X);
#endif
#if ENABLED(X2_IS_TMC)
TMC26XStepper stepperX2(200, X2_ENABLE_PIN, X2_STEP_PIN, X2_DIR_PIN, X2_MAX_CURRENT, X2_SENSE_RESISTOR);
_TMC_DEFINE(X2);
#endif
#if ENABLED(Y_IS_TMC)
TMC26XStepper stepperY(200, Y_ENABLE_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_MAX_CURRENT, Y_SENSE_RESISTOR);
_TMC_DEFINE(Y);
#endif
#if ENABLED(Y2_IS_TMC)
TMC26XStepper stepperY2(200, Y2_ENABLE_PIN, Y2_STEP_PIN, Y2_DIR_PIN, Y2_MAX_CURRENT, Y2_SENSE_RESISTOR);
_TMC_DEFINE(Y2);
#endif
#if ENABLED(Z_IS_TMC)
TMC26XStepper stepperZ(200, Z_ENABLE_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_MAX_CURRENT, Z_SENSE_RESISTOR);
_TMC_DEFINE(Z);
#endif
#if ENABLED(Z2_IS_TMC)
TMC26XStepper stepperZ2(200, Z2_ENABLE_PIN, Z2_STEP_PIN, Z2_DIR_PIN, Z2_MAX_CURRENT, Z2_SENSE_RESISTOR);
_TMC_DEFINE(Z2);
#endif
#if ENABLED(E0_IS_TMC)
TMC26XStepper stepperE0(200, E0_ENABLE_PIN, E0_STEP_PIN, E0_DIR_PIN, E0_MAX_CURRENT, E0_SENSE_RESISTOR);
_TMC_DEFINE(E0);
#endif
#if ENABLED(E1_IS_TMC)
TMC26XStepper stepperE1(200, E1_ENABLE_PIN, E1_STEP_PIN, E1_DIR_PIN, E1_MAX_CURRENT, E1_SENSE_RESISTOR);
_TMC_DEFINE(E1);
#endif
#if ENABLED(E2_IS_TMC)
TMC26XStepper stepperE2(200, E2_ENABLE_PIN, E2_STEP_PIN, E2_DIR_PIN, E2_MAX_CURRENT, E2_SENSE_RESISTOR);
_TMC_DEFINE(E2);
#endif
#if ENABLED(E3_IS_TMC)
TMC26XStepper stepperE3(200, E3_ENABLE_PIN, E3_STEP_PIN, E3_DIR_PIN, E3_MAX_CURRENT, E3_SENSE_RESISTOR);
_TMC_DEFINE(E3);
#endif
#define _TMC_INIT(A) do{ \
stepper##A.setMicrosteps(A##_MICROSTEPS); \
stepper##A.start(); \
} while(0)
}while(0)
void tmc_init() {
#if ENABLED(X_IS_TMC)
@ -127,394 +119,70 @@
//
// TMC2130 Driver objects and inits
//
#if ENABLED(HAVE_TMC2130DRIVER)
#if ENABLED(HAVE_TMC2130)
#include <SPI.h>
#include <Trinamic_TMC2130.h>
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
#ifdef GLOBAL_I_SCALE_ANALOG
#define _2130_set_I_scale_analog(A) stepper##A.set_I_scale_analog(GLOBAL_I_SCALE_ANALOG)
#else
#define _2130_set_I_scale_analog(A) NOOP
#endif
#ifdef GLOBAL_INTERNAL_RSENSE
#define _2130_set_internal_Rsense(A) stepper##A.set_internal_Rsense(GLOBAL_INTERNAL_RSENSE)
#else
#define _2130_set_internal_Rsense(A) NOOP
#endif
#ifdef GLOBAL_EN_PWM_MODE
#define _2130_set_en_pwm_mode(A) stepper##A.set_en_pwm_mode(GLOBAL_EN_PWM_MODE)
#else
#define _2130_set_en_pwm_mode(A) NOOP
#endif
#ifdef GLOBAL_ENC_COMMUTATION
#define _2130_set_enc_commutation(A) stepper##A.set_enc_commutation(GLOBAL_ENC_COMMUTATION)
#else
#define _2130_set_enc_commutation(A) NOOP
#endif
#ifdef GLOBAL_SHAFT
#define _2130_set_shaft(A) stepper##A.set_shaft(GLOBAL_SHAFT)
#else
#define _2130_set_shaft(A) NOOP
#endif
#ifdef GLOBAL_DIAG0_ERROR
#define _2130_set_diag0_error(A) stepper##A.set_diag0_error(GLOBAL_DIAG0_ERROR)
#else
#define _2130_set_diag0_error(A) NOOP
#endif
#ifdef GLOBAL_DIAG0_OTPW
#define _2130_set_diag0_otpw(A) stepper##A.set_diag0_otpw(GLOBAL_DIAG0_OTPW)
#else
#define _2130_set_diag0_otpw(A) NOOP
#endif
#ifdef GLOBAL_DIAG0_STALL
#define _2130_set_diag0_stall(A) stepper##A.set_diag0_stall(GLOBAL_DIAG0_STALL)
#else
#define _2130_set_diag0_stall(A) NOOP
#endif
#ifdef GLOBAL_DIAG1_STALL
#define _2130_set_diag1_stall(A) stepper##A.set_diag1_stall(GLOBAL_DIAG1_STALL)
#else
#define _2130_set_diag1_stall(A) NOOP
#endif
#ifdef GLOBAL_DIAG1_INDEX
#define _2130_set_diag1_index(A) stepper##A.set_diag1_index(GLOBAL_DIAG1_INDEX)
#else
#define _2130_set_diag1_index(A) NOOP
#endif
#ifdef GLOBAL_DIAG1_ONSTATE
#define _2130_set_diag1_onstate(A) stepper##A.set_diag1_onstate(GLOBAL_DIAG1_ONSTATE)
#else
#define _2130_set_diag1_onstate(A) NOOP
#endif
#ifdef GLOBAL_DIAG1_ONSTATE
#define _2130_set_diag1_steps_skipped(A) stepper##A.set_diag1_steps_skipped(GLOBAL_DIAG1_ONSTATE)
#else
#define _2130_set_diag1_steps_skipped(A) NOOP
#endif
#ifdef GLOBAL_DIAG0_INT_PUSHPULL
#define _2130_set_diag0_int_pushpull(A) stepper##A.set_diag0_int_pushpull(GLOBAL_DIAG0_INT_PUSHPULL)
#else
#define _2130_set_diag0_int_pushpull(A) NOOP
#endif
#ifdef GLOBAL_DIAG1_INT_PUSHPULL
#define _2130_set_diag1_int_pushpull(A) stepper##A.set_diag1_int_pushpull(GLOBAL_DIAG1_INT_PUSHPULL)
#else
#define _2130_set_diag1_int_pushpull(A) NOOP
#endif
#ifdef GLOBAL_SMALL_HYSTERESIS
#define _2130_set_small_hysteresis(A) stepper##A.set_small_hysteresis(GLOBAL_SMALL_HYSTERESIS)
#else
#define _2130_set_small_hysteresis(A) NOOP
#endif
#ifdef GLOBAL_STOP_ENABLE
#define _2130_set_stop_enable(A) stepper##A.set_stop_enable(GLOBAL_STOP_ENABLE)
#else
#define _2130_set_stop_enable(A) NOOP
#endif
#ifdef GLOBAL_DIRECT_MODE
#define _2130_set_direct_mode(A) stepper##A.set_direct_mode(GLOBAL_DIRECT_MODE)
#else
#define _2130_set_direct_mode(A) NOOP
#endif
#if defined(GLOBAL_IHOLD) && defined(GLOBAL_IRUN) && defined(GLOBAL_IHOLDDELAY)
#define _2130_set_IHOLD_IRUN(A) stepper##A.set_IHOLD_IRUN(GLOBAL_IHOLD, GLOBAL_IRUN, GLOBAL_IHOLDDELAY)
#else
#define _2130_set_IHOLD_IRUN(A) NOOP
#endif
#ifdef GLOBAL_TPOWERDOWN
#define _2130_set_TPOWERDOWN(A) stepper##A.set_TPOWERDOWN(GLOBAL_TPOWERDOWN)
#else
#define _2130_set_TPOWERDOWN(A) NOOP
#endif
#ifdef GLOBAL_TPWMTHRS
#define _2130_set_TPWMTHRS(A) stepper##A.set_TPWMTHRS(GLOBAL_TPWMTHRS)
#else
#define _2130_set_TPWMTHRS(A) NOOP
#endif
#ifdef GLOBAL_TCOOLTHRS
#define _2130_set_TCOOLTHRS(A) stepper##A.set_TCOOLTHRS(GLOBAL_TCOOLTHRS)
#else
#define _2130_set_TCOOLTHRS(A) NOOP
#endif
#ifdef GLOBAL_THIGH
#define _2130_set_THIGH(A) stepper##A.set_THIGH(GLOBAL_THIGH)
#else
#define _2130_set_THIGH(A) NOOP
#endif
#ifdef GLOBAL_XDIRECT
#define _2130_set_XDIRECT(A) stepper##A.set_XDIRECT(GLOBAL_XDIRECT)
#else
#define _2130_set_XDIRECT(A) NOOP
#endif
#ifdef GLOBAL_VDCMIN
#define _2130_set_VDCMIN(A) stepper##A.set_VDCMIN(GLOBAL_VDCMIN)
#else
#define _2130_set_VDCMIN(A) NOOP
#endif
#ifdef GLOBAL_DEDGE
#define _2130_set_dedge(A) stepper##A.set_dedge(GLOBAL_DEDGE)
#else
#define _2130_set_dedge(A) NOOP
#endif
#ifdef GLOBAL_DISS2G
#define _2130_set_diss2g(A) stepper##A.set_diss2g(GLOBAL_DISS2G)
#else
#define _2130_set_diss2g(A) NOOP
#endif
#ifdef GLOBAL_INTPOL
#define _2130_set_intpol(A) stepper##A.set_intpol(GLOBAL_INTPOL)
#else
#define _2130_set_intpol(A) NOOP
#endif
#ifdef GLOBAL_MRES
#define _2130_set_mres(A) stepper##A.set_mres(GLOBAL_MRES)
#else
#define _2130_set_mres(A) NOOP
#endif
#ifdef GLOBAL_SYNC
#define _2130_set_sync(A) stepper##A.set_sync(GLOBAL_SYNC)
#else
#define _2130_set_sync(A) NOOP
#endif
#ifdef GLOBAL_VHIGHCHM
#define _2130_set_vhighchm(A) stepper##A.set_vhighchm(GLOBAL_VHIGHCHM)
#else
#define _2130_set_vhighchm(A) NOOP
#endif
#ifdef GLOBAL_VHIGHFS
#define _2130_set_vhighfs(A) stepper##A.set_vhighfs(GLOBAL_VHIGHFS)
#else
#define _2130_set_vhighfs(A) NOOP
#endif
#ifdef GLOBAL_VSENSE
#define _2130_set_vsense(A) stepper##A.set_vsense(GLOBAL_VSENSE)
#else
#define _2130_set_vsense(A) NOOP
#endif
#ifdef GLOBAL_TBL
#define _2130_set_tbl(A) stepper##A.set_tbl(GLOBAL_TBL)
#else
#define _2130_set_tbl(A) NOOP
#endif
#ifdef GLOBAL_CHM
#define _2130_set_chm(A) stepper##A.set_chm(GLOBAL_CHM)
#else
#define _2130_set_chm(A) NOOP
#endif
#ifdef GLOBAL_RNDTF
#define _2130_set_rndtf(A) stepper##A.set_rndtf(GLOBAL_RNDTF)
#else
#define _2130_set_rndtf(A) NOOP
#endif
#ifdef GLOBAL_DISFDCC
#define _2130_set_disfdcc(A) stepper##A.set_disfdcc(GLOBAL_DISFDCC)
#else
#define _2130_set_disfdcc(A) NOOP
#endif
#ifdef GLOBAL_FD
#define _2130_set_fd(A) stepper##A.set_fd(GLOBAL_FD)
#else
#define _2130_set_fd(A) NOOP
#endif
#ifdef GLOBAL_HEND
#define _2130_set_hend(A) stepper##A.set_hend(GLOBAL_HEND)
#else
#define _2130_set_hend(A) NOOP
#endif
#ifdef GLOBAL_HSTRT
#define _2130_set_hstrt(A) stepper##A.set_hstrt(GLOBAL_HSTRT)
#else
#define _2130_set_hstrt(A) NOOP
#endif
#ifdef GLOBAL_TOFF
#define _2130_set_toff(A) stepper##A.set_toff(GLOBAL_TOFF)
#else
#define _2130_set_toff(A) NOOP
#endif
#ifdef GLOBAL_SFILT
#define _2130_set_sfilt(A) stepper##A.set_sfilt(GLOBAL_SFILT)
#else
#define _2130_set_sfilt(A) NOOP
#endif
#ifdef GLOBAL_SGT
#define _2130_set_sgt(A) stepper##A.set_sgt(GLOBAL_SGT)
#else
#define _2130_set_sgt(A) NOOP
#endif
#ifdef GLOBAL_SEIMIN
#define _2130_set_seimin(A) stepper##A.set_seimin(GLOBAL_SEIMIN)
#else
#define _2130_set_seimin(A) NOOP
#endif
#ifdef GLOBAL_SEDN
#define _2130_set_sedn(A) stepper##A.set_sedn(GLOBAL_SEDN)
#else
#define _2130_set_sedn(A) NOOP
#endif
#ifdef GLOBAL_SEMAX
#define _2130_set_semax(A) stepper##A.set_semax(GLOBAL_SEMAX)
#else
#define _2130_set_semax(A) NOOP
#endif
#ifdef GLOBAL_SEUP
#define _2130_set_seup(A) stepper##A.set_seup(GLOBAL_SEUP)
#else
#define _2130_set_seup(A) NOOP
#endif
#ifdef GLOBAL_SEMIN
#define _2130_set_semin(A) stepper##A.set_semin(GLOBAL_SEMIN)
#else
#define _2130_set_semin(A) NOOP
#endif
#if defined(GLOBAL_DC_TIME) && defined(GLOBAL_DC_SG)
#define _2130_set_DCCTRL(A) stepper##A.set_DCCTRL(GLOBAL_DC_TIME, GLOBAL_DC_SG)
#else
#define _2130_set_DCCTRL(A) NOOP
#endif
#ifdef GLOBAL_FREEWHEEL
#define _2130_set_freewheel(A) stepper##A.set_freewheel(GLOBAL_FREEWHEEL)
#else
#define _2130_set_freewheel(A) NOOP
#endif
#ifdef GLOBAL_PWM_SYMMETRIC
#define _2130_set_pwm_symmetric(A) stepper##A.set_pwm_symmetric(GLOBAL_PWM_SYMMETRIC)
#else
#define _2130_set_pwm_symmetric(A) NOOP
#endif
#ifdef GLOBAL_PWM_AUTOSCALE
#define _2130_set_pwm_autoscale(A) stepper##A.set_pwm_autoscale(GLOBAL_PWM_AUTOSCALE)
#else
#define _2130_set_pwm_autoscale(A) NOOP
#endif
#ifdef GLOBAL_PWM_FREQ
#define _2130_set_pwm_freq(A) stepper##A.set_pwm_freq(GLOBAL_PWM_FREQ)
#else
#define _2130_set_pwm_freq(A) NOOP
#endif
#ifdef GLOBAL_PWM_GRAD
#define _2130_set_PWM_GRAD(A) stepper##A.set_PWM_GRAD(GLOBAL_PWM_GRAD)
#else
#define _2130_set_PWM_GRAD(A) NOOP
#endif
#ifdef GLOBAL_PWM_AMPL
#define _2130_set_PWM_AMPL(A) stepper##A.set_PWM_AMPL(GLOBAL_PWM_AMPL)
#else
#define _2130_set_PWM_AMPL(A) NOOP
#endif
#ifdef GLOBAL_ENCM_CTRL
#define _2130_set_ENCM_CTRL(A) stepper##A.set_ENCM_CTRL(GLOBAL_ENCM_CTRL)
#else
#define _2130_set_ENCM_CTRL(A) NOOP
#endif
#define _TMC2130_INIT(A) do{ \
stepper##A.init(); \
_2130_set_I_scale_analog(A); \
_2130_set_internal_Rsense(A); \
_2130_set_en_pwm_mode(A); \
_2130_set_enc_commutation(A); \
_2130_set_shaft(A); \
_2130_set_diag0_error(A); \
_2130_set_diag0_otpw(A); \
_2130_set_diag0_stall(A); \
_2130_set_diag1_stall(A); \
_2130_set_diag1_index(A); \
_2130_set_diag1_onstate(A); \
_2130_set_diag1_steps_skipped(A); \
_2130_set_diag0_int_pushpull(A); \
_2130_set_diag1_int_pushpull(A); \
_2130_set_small_hysteresis(A); \
_2130_set_stop_enable(A); \
_2130_set_direct_mode(A); \
_2130_set_IHOLD_IRUN(A); \
_2130_set_TPOWERDOWN(A); \
_2130_set_TPWMTHRS(A); \
_2130_set_TCOOLTHRS(A); \
_2130_set_THIGH(A); \
_2130_set_XDIRECT(A); \
_2130_set_VDCMIN(A); \
_2130_set_dedge(A); \
_2130_set_diss2g(A); \
_2130_set_intpol(A); \
_2130_set_mres(A); \
_2130_set_sync(A); \
_2130_set_vhighchm(A); \
_2130_set_vhighfs(A); \
_2130_set_vsense(A); \
_2130_set_tbl(A); \
_2130_set_chm(A); \
_2130_set_rndtf(A); \
_2130_set_disfdcc(A); \
_2130_set_fd(A); \
_2130_set_hend(A); \
_2130_set_hstrt(A); \
_2130_set_toff(A); \
_2130_set_sfilt(A); \
_2130_set_sgt(A); \
_2130_set_seimin(A); \
_2130_set_sedn(A); \
_2130_set_semax(A); \
_2130_set_seup(A); \
_2130_set_semin(A); \
_2130_set_DCCTRL(A); \
_2130_set_freewheel(A); \
_2130_set_pwm_symmetric(A); \
_2130_set_pwm_autoscale(A); \
_2130_set_pwm_freq(A); \
_2130_set_PWM_GRAD(A); \
_2130_set_PWM_AMPL(A); \
_2130_set_ENCM_CTRL(A); \
} while(0)
#else // !TMC2130_ADVANCED_CONFIGURATION
#define _TMC2130_INIT(A) do{ \
stepper##A.init(); \
stepper##A.set_mres(A##_MRES); \
stepper##A.set_IHOLD_IRUN(A##_IHOLD, A##_IRUN, A##_IHOLDDELAY); \
stepper##A.set_I_scale_analog(A##_I_SCALE_ANALOG); \
stepper##A.set_tbl(A##_TBL); \
stepper##A.set_toff(A##_TOFF); \
} while(0)
#include <TMC2130Stepper.h>
#endif // TMC2130_ADVANCED_CONFIGURATION
#define _TMC2130_DEFINE(ST) TMC2130Stepper stepper##ST(ST##_ENABLE_PIN, ST##_DIR_PIN, ST##_STEP_PIN, ST##_CHIP_SELECT)
// Stepper objects of TMC2310 steppers used
// Stepper objects of TMC2130 steppers used
#if ENABLED(X_IS_TMC2130)
Trinamic_TMC2130 stepperX(X_CS_PIN);
_TMC2130_DEFINE(X);
#endif
#if ENABLED(X2_IS_TMC2130)
Trinamic_TMC2130 stepperX2(X2_CS_PIN);
_TMC2130_DEFINE(X2);
#endif
#if ENABLED(Y_IS_TMC2130)
Trinamic_TMC2130 stepperY(Y_CS_PIN);
_TMC2130_DEFINE(Y);
#endif
#if ENABLED(Y2_IS_TMC2130)
Trinamic_TMC2130 stepperY2(Y2_CS_PINR);
_TMC2130_DEFINE(Y2);
#endif
#if ENABLED(Z_IS_TMC2130)
Trinamic_TMC2130 stepperZ(Z_CS_PIN);
_TMC2130_DEFINE(Z);
#endif
#if ENABLED(Z2_IS_TMC2130)
Trinamic_TMC2130 stepperZ2(Z2_CS_PIN);
_TMC2130_DEFINE(Z2);
#endif
#if ENABLED(E0_IS_TMC2130)
Trinamic_TMC2130 stepperE0(E0_CS_PIN);
_TMC2130_DEFINE(E0);
#endif
#if ENABLED(E1_IS_TMC2130)
Trinamic_TMC2130 stepperE1(E1_CS_PIN);
_TMC2130_DEFINE(E1);
#endif
#if ENABLED(E2_IS_TMC2130)
Trinamic_TMC2130 stepperE2(E2_CS_PIN);
_TMC2130_DEFINE(E2);
#endif
#if ENABLED(E3_IS_TMC2130)
Trinamic_TMC2130 stepperE3(E3_CS_PIN);
_TMC2130_DEFINE(E3);
#endif
// Use internal reference voltage for current calculations. This is the default.
// Following values from Trinamic's spreadsheet with values for a NEMA17 (42BYGHW609)
void tmc2130_init(TMC2130Stepper &st, const uint16_t max_current, const uint16_t microsteps) {
st.begin();
st.setCurrent(st.getCurrent(), R_SENSE, HOLD_MULTIPLIER);
st.microsteps(microsteps);
st.blank_time(24);
st.off_time(8);
st.interpolate(INTERPOLATE);
#if ENABLED(STEALTHCHOP)
st.stealthChop(1);
#endif
#if ENABLED(SENSORLESS_HOMING)
st.coolstep_min_speed(1048575);
st.sg_stall_value(STALL_THRESHOLD);
st.sg_filter(1);
st.diag1_stall(1);
st.diag1_active_high(1);
#endif
}
#define _TMC2130_INIT(ST) tmc2130_init(stepper##ST, ST##_MAX_CURRENT, ST##_MICROSTEPS)
void tmc2130_init() {
delay(500); // Let power stabilize before configuring the steppers
#if ENABLED(X_IS_TMC2130)
_TMC2130_INIT(X);
#endif
@ -545,9 +213,11 @@
#if ENABLED(E3_IS_TMC2130)
_TMC2130_INIT(E3);
#endif
TMC2130_ADV()
}
#endif // HAVE_TMC2130
#endif // HAVE_TMC2130DRIVER
//
// L6470 Driver objects and inits
@ -557,36 +227,38 @@
#include <SPI.h>
#include <L6470.h>
#define _L6470_DEFINE(ST) L6470 stepper##ST(ST##_ENABLE_PIN)
// L6470 Stepper objects
#if ENABLED(X_IS_L6470)
L6470 stepperX(X_ENABLE_PIN);
_L6470_DEFINE(X);
#endif
#if ENABLED(X2_IS_L6470)
L6470 stepperX2(X2_ENABLE_PIN);
_L6470_DEFINE(X2);
#endif
#if ENABLED(Y_IS_L6470)
L6470 stepperY(Y_ENABLE_PIN);
_L6470_DEFINE(Y);
#endif
#if ENABLED(Y2_IS_L6470)
L6470 stepperY2(Y2_ENABLE_PIN);
_L6470_DEFINE(Y2);
#endif
#if ENABLED(Z_IS_L6470)
L6470 stepperZ(Z_ENABLE_PIN);
_L6470_DEFINE(Z);
#endif
#if ENABLED(Z2_IS_L6470)
L6470 stepperZ2(Z2_ENABLE_PIN);
_L6470_DEFINE(Z2);
#endif
#if ENABLED(E0_IS_L6470)
L6470 stepperE0(E0_ENABLE_PIN);
_L6470_DEFINE(E0);
#endif
#if ENABLED(E1_IS_L6470)
L6470 stepperE1(E1_ENABLE_PIN);
_L6470_DEFINE(E1);
#endif
#if ENABLED(E2_IS_L6470)
L6470 stepperE2(E2_ENABLE_PIN);
_L6470_DEFINE(E2);
#endif
#if ENABLED(E3_IS_L6470)
L6470 stepperE3(E3_ENABLE_PIN);
_L6470_DEFINE(E3);
#endif
#define _L6470_INIT(A) do{ \

46
Marlin/stepper_indirection.h
View File

@ -53,10 +53,8 @@
void tmc_init();
#endif
// TMC130 drivers have STEP/DIR/ENABLE on normal pins
#if ENABLED(HAVE_TMC2130DRIVER)
#include <SPI.h>
#include <Trinamic_TMC2130.h>
#if ENABLED(HAVE_TMC2130)
#include <TMC2130Stepper.h>
void tmc2130_init();
#endif
@ -83,8 +81,8 @@
#define X_ENABLE_WRITE(STATE) stepperX.setEnabled(STATE)
#define X_ENABLE_READ stepperX.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(X_IS_TMC2130)
extern Trinamic_TMC2130 stepperX;
#if ENABLED(HAVE_TMC2130) && ENABLED(X_IS_TMC2130)
extern TMC2130Stepper stepperX;
#endif
#define X_ENABLE_INIT SET_OUTPUT(X_ENABLE_PIN)
#define X_ENABLE_WRITE(STATE) WRITE(X_ENABLE_PIN,STATE)
@ -114,8 +112,8 @@
#define Y_ENABLE_WRITE(STATE) stepperY.setEnabled(STATE)
#define Y_ENABLE_READ stepperY.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Y_IS_TMC2130)
extern Trinamic_TMC2130 stepperY;
#if ENABLED(HAVE_TMC2130) && ENABLED(Y_IS_TMC2130)
extern TMC2130Stepper stepperY;
#endif
#define Y_ENABLE_INIT SET_OUTPUT(Y_ENABLE_PIN)
#define Y_ENABLE_WRITE(STATE) WRITE(Y_ENABLE_PIN,STATE)
@ -145,8 +143,8 @@
#define Z_ENABLE_WRITE(STATE) stepperZ.setEnabled(STATE)
#define Z_ENABLE_READ stepperZ.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Z_IS_TMC2130)
extern Trinamic_TMC2130 stepperZ;
#if ENABLED(HAVE_TMC2130) && ENABLED(Z_IS_TMC2130)
extern TMC2130Stepper stepperZ;
#endif
#define Z_ENABLE_INIT SET_OUTPUT(Z_ENABLE_PIN)
#define Z_ENABLE_WRITE(STATE) WRITE(Z_ENABLE_PIN,STATE)
@ -177,8 +175,8 @@
#define X2_ENABLE_WRITE(STATE) stepperX2.setEnabled(STATE)
#define X2_ENABLE_READ stepperX2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(X2_IS_TMC2130)
extern Trinamic_TMC2130 stepperX2;
#if ENABLED(HAVE_TMC2130) && ENABLED(X2_IS_TMC2130)
extern TMC2130Stepper stepperX2;
#endif
#define X2_ENABLE_INIT SET_OUTPUT(X2_ENABLE_PIN)
#define X2_ENABLE_WRITE(STATE) WRITE(X2_ENABLE_PIN,STATE)
@ -210,8 +208,8 @@
#define Y2_ENABLE_WRITE(STATE) stepperY2.setEnabled(STATE)
#define Y2_ENABLE_READ stepperY2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Y2_IS_TMC2130)
extern Trinamic_TMC2130 stepperY2;
#if ENABLED(HAVE_TMC2130) && ENABLED(Y2_IS_TMC2130)
extern TMC2130Stepper stepperY2;
#endif
#define Y2_ENABLE_INIT SET_OUTPUT(Y2_ENABLE_PIN)
#define Y2_ENABLE_WRITE(STATE) WRITE(Y2_ENABLE_PIN,STATE)
@ -243,8 +241,8 @@
#define Z2_ENABLE_WRITE(STATE) stepperZ2.setEnabled(STATE)
#define Z2_ENABLE_READ stepperZ2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Z2_IS_TMC2130)
extern Trinamic_TMC2130 stepperZ2;
#if ENABLED(HAVE_TMC2130) && ENABLED(Z2_IS_TMC2130)
extern TMC2130Stepper stepperZ2;
#endif
#define Z2_ENABLE_INIT SET_OUTPUT(Z2_ENABLE_PIN)
#define Z2_ENABLE_WRITE(STATE) WRITE(Z2_ENABLE_PIN,STATE)
@ -275,8 +273,8 @@
#define E0_ENABLE_WRITE(STATE) stepperE0.setEnabled(STATE)
#define E0_ENABLE_READ stepperE0.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E0_IS_TMC2130)
extern Trinamic_TMC2130 stepperE0;
#if ENABLED(HAVE_TMC2130) && ENABLED(E0_IS_TMC2130)
extern TMC2130Stepper stepperE0;
#endif
#define E0_ENABLE_INIT SET_OUTPUT(E0_ENABLE_PIN)
#define E0_ENABLE_WRITE(STATE) WRITE(E0_ENABLE_PIN,STATE)
@ -306,8 +304,8 @@
#define E1_ENABLE_WRITE(STATE) stepperE1.setEnabled(STATE)
#define E1_ENABLE_READ stepperE1.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E1_IS_TMC2130)
extern Trinamic_TMC2130 stepperE1;
#if ENABLED(HAVE_TMC2130) && ENABLED(E1_IS_TMC2130)
extern TMC2130Stepper stepperE1;
#endif
#define E1_ENABLE_INIT SET_OUTPUT(E1_ENABLE_PIN)
#define E1_ENABLE_WRITE(STATE) WRITE(E1_ENABLE_PIN,STATE)
@ -337,8 +335,8 @@
#define E2_ENABLE_WRITE(STATE) stepperE2.setEnabled(STATE)
#define E2_ENABLE_READ stepperE2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E2_IS_TMC2130)
extern Trinamic_TMC2130 stepperE2;
#if ENABLED(HAVE_TMC2130) && ENABLED(E2_IS_TMC2130)
extern TMC2130Stepper stepperE2;
#endif
#define E2_ENABLE_INIT SET_OUTPUT(E2_ENABLE_PIN)
#define E2_ENABLE_WRITE(STATE) WRITE(E2_ENABLE_PIN,STATE)
@ -368,8 +366,8 @@
#define E3_ENABLE_WRITE(STATE) stepperE3.setEnabled(STATE)
#define E3_ENABLE_READ stepperE3.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E3_IS_TMC2130)
extern Trinamic_TMC2130 stepperE3;
#if ENABLED(HAVE_TMC2130) && ENABLED(E3_IS_TMC2130)
extern TMC2130Stepper stepperE3;
#endif
#define E3_ENABLE_INIT SET_OUTPUT(E3_ENABLE_PIN)
#define E3_ENABLE_WRITE(STATE) WRITE(E3_ENABLE_PIN,STATE)

Write Preview
Loading…
Cancel
Save