andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

GTM32 Pro pins updates (#14505)

pull/1/head
Alexander Amelkin 5 years ago
committed by Scott Lahteine
parent
10a71e332d
commit
7a42132002
1 changed files with 118 additions and 79 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 197
      Marlin/src/pins/pins_GTM32_PRO_VB.h

197
Marlin/src/pins/pins_GTM32_PRO_VB.h
View File

@ -34,21 +34,36 @@
#define BOARD_NAME "GTM32 Pro VB"
//#define DISABLE_DEBUG
//
// It is required to disable JTAG function because its pins are
// used as GPIO to drive the Y axis stepper.
// DO NOT ENABLE!
//
#define DISABLE_JTAG
//
// If you don't need the SWDIO functionality (any more), you may
// disable SWD here to regain PA13/PA14 pins for other use.
//
//#define DISABLE_JTAGSWD
// Ignore temp readings during development.
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // EEPROM end address (4kB)
//
// Limit Switches
//
#define X_MIN_PIN PE5
#define X_MAX_PIN PE4
#define Y_MIN_PIN PE3
#define Y_MAX_PIN PE2
#define Z_MIN_PIN PE1
#define Z_MAX_PIN PE0
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
//
// Steppers
@ -65,46 +80,52 @@
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
#define E0_STEP_PIN PB2
#define E0_DIR_PIN PB11
#define E0_ENABLE_PIN PC4
// Extruder stepper pins
// NOTE: Numbering here is made according to EXT connector numbers,
// the FANx_PWM line numbering in the schematics is reverse.
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PC14
#define E2_DIR_PIN PC13
#define E2_ENABLE_PIN PC15
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
//
// Heaters / Fans
//
#define HEATER_0_PIN PB0
#define HEATER_1_PIN PB5
#define HEATER_2_PIN PB4
#define HEATER_BED_PIN PB1
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define FAN_PIN PB7 // TODO: Add functionality
#define FAN1_PIN PB8 // TODO: Add functionality
#define FAN2_PIN PB9 // TODO: Add functionality
//
// These are FAN PWM pins on EXT0..EXT2 connectors.
//
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2 // PORT NUMBERING
#define TEMP_1_PIN PC1 // PORT NUMBERING
#define TEMP_2_PIN PC0 // PORT NUMBERING
#define TEMP_BED_PIN PC3 // PORT NUMBERING
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
//
// Misc. Functions
//
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//#define RESET_PIN NRST
#define T_PEN PE6
#define BEEPER_PIN PB10
//
// LCD / Controller
@ -112,6 +133,11 @@
#if HAS_SPI_LCD
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
//
// LCD display on J2 FFC40
// Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
@ -119,12 +145,12 @@
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define SD_DETECT_PIN PC7
#define KILL_PIN -1
#else
//
// Serial LCDs can be implemented in ExtUI
//
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
#endif
#ifndef ST7920_DELAY_1
@ -137,59 +163,72 @@
#define ST7920_DELAY_3 DELAY_NS(715)
#endif
//
// UART LCD Pins, if used
//
//#define LCD_PINS_D14 PD9 // RXD3
//#define LCD_PINS_D13 PD8 // TXD3
#endif // HAS_SPI_LCD
//
// SPI2 on LCD conn
//
#define SPI2_MOSI PB15
#define SPI2_MISO PB14
#define SPI2_SCK PB13
#define SPI2_NSS PB12
//
// SD Card on LCD
//
#define SD_CD PC7
#define SD_DATA0 PC8
#define SD_DATA1 PC9
#define SD_DATA2 PC10
#define SD_DATA3 PC11
#define SD_CMD PD2
#define SD_CLK PC12
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
//
// Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
//
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
//
// SPI Flash (on board Card Socket)
//
#define SPI1_NSS PA4
#define SPI1_SCK PA5
#define SPI1_MISO PA6
#define SPI1_MOSI PA7
#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
#endif
//
// Debug
// Beeper
//
//#define SDA PA13
//#define SCL PA14
#ifdef GTM32_PRO_VB_USE_LCD_BEEPER
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
// on Geeetech's version of RepRapDiscount Smart Controller
// (e.g. on Rostock 301)
#define BEEPER_PIN PE12
#else
// This is the beeper on the board itself
#define BEEPER_PIN PB10
#endif
//
// Wifi
//
#define USART2_RX PA3 // Default alternate function
#define USART2_TX PA2 // Default alternate function
/**
* The on-board TF_CARD_SOCKET microSD card socket has no SD Detect pin wired.
*
* The FFC10 (SD_CARD) connector has the same pins as those routed to the FFC40 (J2)
* connector, which usually go to the SD Card slot on the Geeetech version of the
* RepRapDiscount Smart Controller. Both connectors have the card detect signal.
*
* The on-board SD card and the external card (on either SD_CARD or J2) are two
* separate devices and can work simultaneously. Unfortunately, Marlin only supports
* a single SPI Flash device (as of 2019-07-05) so only one is enabled here.
*/
#if ENABLED(GTM32_PRO_VB_USE_EXT_SDCARD)
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
//
// For future use
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
//
//#undef USB_DM
//#undef CAN_TX
//#undef USB_DP
//#undef CAN_RX
//#undef BOARD_JTDI_PIN
//#define BOOT0 BOOT0
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1

Write Preview
Loading…
Cancel
Save