diff --git a/Marlin/src/pins/pins_GTM32_PRO_VB.h b/Marlin/src/pins/pins_GTM32_PRO_VB.h index 87b32bf38a..82a8e39555 100644 --- a/Marlin/src/pins/pins_GTM32_PRO_VB.h +++ b/Marlin/src/pins/pins_GTM32_PRO_VB.h @@ -34,21 +34,36 @@ #define BOARD_NAME "GTM32 Pro VB" //#define DISABLE_DEBUG + +// +// It is required to disable JTAG function because its pins are +// used as GPIO to drive the Y axis stepper. +// DO NOT ENABLE! +// #define DISABLE_JTAG + +// +// If you don't need the SWDIO functionality (any more), you may +// disable SWD here to regain PA13/PA14 pins for other use. +// //#define DISABLE_JTAGSWD // Ignore temp readings during development. #define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Enable EEPROM Emulation for this board as it doesn't have EEPROM +#define FLASH_EEPROM_EMULATION +#define E2END 0xFFF // EEPROM end address (4kB) + // // Limit Switches // -#define X_MIN_PIN PE5 -#define X_MAX_PIN PE4 -#define Y_MIN_PIN PE3 -#define Y_MAX_PIN PE2 -#define Z_MIN_PIN PE1 -#define Z_MAX_PIN PE0 +#define X_MIN_PIN PE5 // ENDSTOPS 15,17 +#define X_MAX_PIN PE4 // ENDSTOPS 16,18 +#define Y_MIN_PIN PE3 // ENDSTOPS 9,11 +#define Y_MAX_PIN PE2 // ENDSTOPS 10,12 +#define Z_MIN_PIN PE1 // ENDSTOPS 3,5 +#define Z_MAX_PIN PE0 // ENDSTOPS 4,6 // // Steppers @@ -65,46 +80,52 @@ #define Z_DIR_PIN PD3 #define Z_ENABLE_PIN PB3 -#define E0_STEP_PIN PB2 -#define E0_DIR_PIN PB11 -#define E0_ENABLE_PIN PC4 +// Extruder stepper pins +// NOTE: Numbering here is made according to EXT connector numbers, +// the FANx_PWM line numbering in the schematics is reverse. +// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step +// stick that drives the EXT0 output on the board. +// +#define E0_STEP_PIN PC14 +#define E0_DIR_PIN PC13 +#define E0_ENABLE_PIN PC15 #define E1_STEP_PIN PA0 #define E1_DIR_PIN PB6 #define E1_ENABLE_PIN PA1 -#define E2_STEP_PIN PC14 -#define E2_DIR_PIN PC13 -#define E2_ENABLE_PIN PC15 +#define E2_STEP_PIN PB2 +#define E2_DIR_PIN PB11 +#define E2_ENABLE_PIN PC4 // // Heaters / Fans // -#define HEATER_0_PIN PB0 -#define HEATER_1_PIN PB5 -#define HEATER_2_PIN PB4 -#define HEATER_BED_PIN PB1 +#define HEATER_0_PIN PB0 // EXT0 port +#define HEATER_1_PIN PB5 // EXT1 port +#define HEATER_2_PIN PB4 // EXT2 port +#define HEATER_BED_PIN PB1 // CON2X3 hotbed port -#define FAN_PIN PB7 // TODO: Add functionality -#define FAN1_PIN PB8 // TODO: Add functionality -#define FAN2_PIN PB9 // TODO: Add functionality +// +// These are FAN PWM pins on EXT0..EXT2 connectors. +// +//#define FAN_PIN PB9 // EXT0 port +#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan +#define FAN1_PIN PB8 // EXT1 port +#define FAN2_PIN PB7 // EXT2 port // // Temperature Sensors // -#define TEMP_0_PIN PC2 // PORT NUMBERING -#define TEMP_1_PIN PC1 // PORT NUMBERING -#define TEMP_2_PIN PC0 // PORT NUMBERING -#define TEMP_BED_PIN PC3 // PORT NUMBERING +#define TEMP_0_PIN PC2 // EXT0 port +#define TEMP_1_PIN PC1 // EXT1 port +#define TEMP_2_PIN PC0 // EXT2 port +#define TEMP_BED_PIN PC3 // CON2X3 hotbed port // // Misc. Functions // #define LED_PWM PD12 // External LED, pin 2 on LED labeled connector -//#define RESET_PIN NRST -#define T_PEN PE6 - -#define BEEPER_PIN PB10 // // LCD / Controller @@ -112,6 +133,11 @@ #if HAS_SPI_LCD #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + // + // LCD display on J2 FFC40 + // Geeetech's LCD2004A Control Panel is very much like + // RepRapDiscount Smart Controller, but adds an FFC40 connector + // #define LCD_PINS_RS PE6 // CS chip select /SS chip slave select #define LCD_PINS_ENABLE PE14 // SID (MOSI) #define LCD_PINS_D4 PD8 // SCK (CLK) clock @@ -119,12 +145,12 @@ #define LCD_PINS_D6 PD10 #define LCD_PINS_D7 PE15 - #define BTN_EN1 PE8 - #define BTN_EN2 PE9 - #define BTN_ENC PE13 - - #define SD_DETECT_PIN PC7 - #define KILL_PIN -1 + #else + // + // Serial LCDs can be implemented in ExtUI + // + //#define LCD_UART_TX PD8 + //#define LCD_UART_RX PD9 #endif #ifndef ST7920_DELAY_1 @@ -137,59 +163,72 @@ #define ST7920_DELAY_3 DELAY_NS(715) #endif - // - // UART LCD Pins, if used - // - //#define LCD_PINS_D14 PD9 // RXD3 - //#define LCD_PINS_D13 PD8 // TXD3 - #endif // HAS_SPI_LCD -// -// SPI2 on LCD conn -// -#define SPI2_MOSI PB15 -#define SPI2_MISO PB14 -#define SPI2_SCK PB13 -#define SPI2_NSS PB12 - -// -// SD Card on LCD -// -#define SD_CD PC7 -#define SD_DATA0 PC8 -#define SD_DATA1 PC9 -#define SD_DATA2 PC10 -#define SD_DATA3 PC11 -#define SD_CMD PD2 -#define SD_CLK PC12 +#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + // + // Geeetech's LCD2004A Control Panel is very much like + // RepRapDiscount Smart Controller, but adds an FFC40 connector + // connected with a flat wire to J2 connector on the board. + // + #define BTN_EN1 PE8 + #define BTN_EN2 PE9 + #define BTN_ENC PE13 -// -// SPI Flash (on board Card Socket) -// -#define SPI1_NSS PA4 -#define SPI1_SCK PA5 -#define SPI1_MISO PA6 -#define SPI1_MOSI PA7 + #define GTM32_PRO_VB_USE_LCD_BEEPER + #define GTM32_PRO_VB_USE_EXT_SDCARD +#endif // -// Debug +// Beeper // -//#define SDA PA13 -//#define SCL PA14 +#ifdef GTM32_PRO_VB_USE_LCD_BEEPER + // This is pin 32 on J2 FFC40 and pin, goes to the beeper + // on Geeetech's version of RepRapDiscount Smart Controller + // (e.g. on Rostock 301) + #define BEEPER_PIN PE12 +#else + // This is the beeper on the board itself + #define BEEPER_PIN PB10 +#endif -// -// Wifi -// -#define USART2_RX PA3 // Default alternate function -#define USART2_TX PA2 // Default alternate function +/** + * The on-board TF_CARD_SOCKET microSD card socket has no SD Detect pin wired. + * + * The FFC10 (SD_CARD) connector has the same pins as those routed to the FFC40 (J2) + * connector, which usually go to the SD Card slot on the Geeetech version of the + * RepRapDiscount Smart Controller. Both connectors have the card detect signal. + * + * The on-board SD card and the external card (on either SD_CARD or J2) are two + * separate devices and can work simultaneously. Unfortunately, Marlin only supports + * a single SPI Flash device (as of 2019-07-05) so only one is enabled here. + */ +#if ENABLED(GTM32_PRO_VB_USE_EXT_SDCARD) + // + // SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector + // + #define SS_PIN PC11 + #define SCK_PIN PC12 + #define MOSI_PIN PD2 + #define MISO_PIN PC8 + #define SD_DETECT_PIN PC7 +#else + // + // Use the on-board card socket labeled TF_CARD_SOCKET + // + #define SS_PIN PA4 + #define SCK_PIN PA5 + #define MOSI_PIN PA7 + #define MISO_PIN PA6 + #define SD_DETECT_PIN -1 // Card detect is not connected +#endif +#define SDSS SS_PIN + // -// For future use +// ESP WiFi can be soldered to J9 connector which is wired to USART2. +// Must define WIFISUPPORT in Configuration.h for the printer. // -//#undef USB_DM -//#undef CAN_TX -//#undef USB_DP -//#undef CAN_RX -//#undef BOARD_JTDI_PIN -//#define BOOT0 BOOT0 +#define ESP_WIFI_MODULE_COM 2 +#define ESP_WIFI_MODULE_BAUDRATE 115200 +#define ESP_WIFI_MODULE_RESET_PIN -1