Bob Kuhn
5 years ago
committed by
GitHub
GitHub
10 changed files with 208 additions and 31 deletions
@ -0,0 +1,42 @@ |
|||||
|
/**
|
||||
|
* Marlin 3D Printer Firmware |
||||
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
|
* |
||||
|
* Based on Sprinter and grbl. |
||||
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
||||
|
* |
||||
|
* This program is free software: you can redistribute it and/or modify |
||||
|
* it under the terms of the GNU General Public License as published by |
||||
|
* the Free Software Foundation, either version 3 of the License, or |
||||
|
* (at your option) any later version. |
||||
|
* |
||||
|
* This program is distributed in the hope that it will be useful, |
||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
||||
|
* GNU General Public License for more details. |
||||
|
* |
||||
|
* You should have received a copy of the GNU General Public License |
||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
* |
||||
|
*/ |
||||
|
#pragma once |
||||
|
|
||||
|
/**
|
||||
|
* Pin assignments for the MKS RUMBA32 |
||||
|
* |
||||
|
* https://aus3d.com.au/rumba32
|
||||
|
* https://github.com/Aus3D/RUMBA32
|
||||
|
* |
||||
|
* The MKS and Aus3D versions have the same pinout but the MKS version |
||||
|
* has some added resistors and LEDs. The resistors needed for the |
||||
|
* TMC2208/9 UART interface are among the additions. Also added were |
||||
|
* connectors and resistors dedicated to the TMC2130 sensorless homing |
||||
|
* interface. |
||||
|
*/ |
||||
|
|
||||
|
#define BOARD_INFO_NAME "Aus3D RUMBA32" |
||||
|
|
||||
|
#define RUMBA32_V1_0 |
||||
|
//#define I2C_EEPROM
|
||||
|
|
||||
|
#include "pins_RUMBA32_common.h" |
||||
@ -0,0 +1,109 @@ |
|||||
|
/**
|
||||
|
* Marlin 3D Printer Firmware |
||||
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
|
* |
||||
|
* Based on Sprinter and grbl. |
||||
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm |
||||
|
* |
||||
|
* This program is free software: you can redistribute it and/or modify |
||||
|
* it under the terms of the GNU General Public License as published by |
||||
|
* the Free Software Foundation, either version 3 of the License, or |
||||
|
* (at your option) any later version. |
||||
|
* |
||||
|
* This program is distributed in the hope that it will be useful, |
||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
||||
|
* GNU General Public License for more details. |
||||
|
* |
||||
|
* You should have received a copy of the GNU General Public License |
||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
* |
||||
|
*/ |
||||
|
#pragma once |
||||
|
|
||||
|
/**
|
||||
|
* Pin assignments for the MKS RUMBA32 |
||||
|
* |
||||
|
* https://github.com/makerbase-mks/MKS-RUMBA32
|
||||
|
* |
||||
|
* The MKS and Aus3D versions have the same pinout but the MKS version |
||||
|
* has some added resistors and LEDs. The resistors needed for the |
||||
|
* TMC2208/9 UART interface are among the additions. Also added were |
||||
|
* connectors and resistors dedicated to the TMC2130 sensorless homing |
||||
|
* interface. |
||||
|
*/ |
||||
|
|
||||
|
#define BOARD_INFO_NAME "MKS RUMBA32" |
||||
|
|
||||
|
#define RUMBA32_V1_0 |
||||
|
#define ENABLE_SPI1 |
||||
|
//#define I2C_EEPROM
|
||||
|
|
||||
|
#include "pins_RUMBA32_common.h" |
||||
|
|
||||
|
//
|
||||
|
// Software SPI pins for TMC2130 stepper drivers
|
||||
|
//
|
||||
|
#if ENABLED(TMC_USE_SW_SPI) |
||||
|
#ifndef TMC_SW_MOSI |
||||
|
#define TMC_SW_MOSI PA7 |
||||
|
#endif |
||||
|
#ifndef TMC_SW_MISO |
||||
|
#define TMC_SW_MISO PA6 |
||||
|
#endif |
||||
|
#ifndef TMC_SW_SCK |
||||
|
#define TMC_SW_SCK PA5 |
||||
|
#endif |
||||
|
#endif |
||||
|
|
||||
|
#if HAS_TMC220x |
||||
|
/**
|
||||
|
* TMC2208/TMC2209 stepper drivers |
||||
|
* |
||||
|
* Hardware serial communication ports. |
||||
|
* If undefined software serial is used according to the pins below |
||||
|
*/ |
||||
|
//#define X_HARDWARE_SERIAL Serial
|
||||
|
//#define X2_HARDWARE_SERIAL Serial1
|
||||
|
//#define Y_HARDWARE_SERIAL Serial1
|
||||
|
//#define Y2_HARDWARE_SERIAL Serial1
|
||||
|
//#define Z_HARDWARE_SERIAL Serial1
|
||||
|
//#define Z2_HARDWARE_SERIAL Serial1
|
||||
|
//#define E0_HARDWARE_SERIAL Serial1
|
||||
|
//#define E1_HARDWARE_SERIAL Serial1
|
||||
|
//#define E2_HARDWARE_SERIAL Serial1
|
||||
|
//#define E3_HARDWARE_SERIAL Serial1
|
||||
|
//#define E4_HARDWARE_SERIAL Serial1
|
||||
|
|
||||
|
//
|
||||
|
// Software serial
|
||||
|
//
|
||||
|
#define X_SERIAL_TX_PIN PA3 |
||||
|
#define X_SERIAL_RX_PIN PC14 |
||||
|
|
||||
|
#define Y_SERIAL_TX_PIN PA4 |
||||
|
#define Y_SERIAL_RX_PIN PE4 |
||||
|
|
||||
|
#define Z_SERIAL_TX_PIN PD13 |
||||
|
#define Z_SERIAL_RX_PIN PE0 |
||||
|
|
||||
|
#define E0_SERIAL_TX_PIN PD14 |
||||
|
#define E0_SERIAL_RX_PIN PC13 |
||||
|
|
||||
|
#define E1_SERIAL_TX_PIN PD15 |
||||
|
#define E1_SERIAL_RX_PIN PD5 |
||||
|
|
||||
|
#define E2_SERIAL_TX_PIN PD12 |
||||
|
#define E2_SERIAL_RX_PIN PD1 |
||||
|
#endif |
||||
|
|
||||
|
//
|
||||
|
// LCD / Controller
|
||||
|
//
|
||||
|
|
||||
|
// Alter timing for graphical display
|
||||
|
#if HAS_GRAPHICAL_LCD |
||||
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96) |
||||
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48) |
||||
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(600) |
||||
|
#endif |
||||
Loading…
Reference in new issue