Browse Source

PROBING_HEATERS_OFF sub-option WAIT_FOR_HOTEND (#20835)

vanilla_fb_2.0.x
Katelyn Schiesser 4 years ago
committed by Scott Lahteine
parent
commit
7240c2172b
  1. 1
      Marlin/Configuration.h
  2. 7
      Marlin/src/module/motion.cpp
  3. 4
      Marlin/src/module/probe.cpp
  4. 11
      Marlin/src/module/temperature.cpp
  5. 4
      Marlin/src/module/temperature.h

1
Marlin/Configuration.h

@ -1139,6 +1139,7 @@
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
//#define WAIT_FOR_HOTEND // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing

7
Marlin/src/module/motion.cpp

@ -1318,11 +1318,16 @@ void prepare_line_to_destination() {
if (is_home_dir) {
if (TERN0(HOMING_Z_WITH_PROBE, axis == Z_AXIS)) {
#if ALL(HAS_HEATED_BED, WAIT_FOR_BED_HEATER)
#if BOTH(HAS_HEATED_BED, WAIT_FOR_BED_HEATER)
// Wait for bed to heat back up between probing points
thermalManager.wait_for_bed_heating();
#endif
#if BOTH(HAS_HOTEND, WAIT_FOR_HOTEND)
// Wait for the hotend to heat back up between probing points
thermalManager.wait_for_hotend_heating(active_extruder);
#endif
TERN_(HAS_QUIET_PROBING, if (final_approach) probe.set_probing_paused(true));
}

4
Marlin/src/module/probe.cpp

@ -478,6 +478,10 @@ bool Probe::probe_down_to_z(const float z, const feedRate_t fr_mm_s) {
thermalManager.wait_for_bed_heating();
#endif
#if BOTH(HAS_TEMP_HOTEND, WAIT_FOR_HOTEND)
thermalManager.wait_for_hotend_heating(active_extruder);
#endif
if (TERN0(BLTOUCH_SLOW_MODE, bltouch.deploy())) return true; // Deploy in LOW SPEED MODE on every probe action
// Disable stealthChop if used. Enable diag1 pin on driver.

11
Marlin/src/module/temperature.cpp

@ -3447,6 +3447,17 @@ void Temperature::tick() {
return false;
}
#if ENABLED(WAIT_FOR_HOTEND)
void Temperature::wait_for_hotend_heating(const uint8_t target_extruder) {
if (isHeatingHotend(target_extruder)) {
SERIAL_ECHOLNPGM("Wait for hotend heating...");
LCD_MESSAGEPGM(MSG_HEATING);
wait_for_hotend(target_extruder);
ui.reset_status();
}
}
#endif
#endif // HAS_TEMP_HOTEND
#if HAS_HEATED_BED

4
Marlin/src/module/temperature.h

@ -630,6 +630,10 @@ class Temperature {
, const bool click_to_cancel=false
#endif
);
#if ENABLED(WAIT_FOR_HOTEND)
static void wait_for_hotend_heating(const uint8_t target_extruder);
#endif
#endif
FORCE_INLINE static bool still_heating(const uint8_t e) {

Loading…
Cancel
Save