Include bed hysteresis setting in the example configs

Marlin/Configuration.h

@@ -192,11 +192,12 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109/M190 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
 #define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.

Marlin/example_configurations/Felix/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 15  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 15  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/Hephestos/Configuration.h

@@ -195,11 +195,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/K8200/Configuration.h

@@ -199,11 +199,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/RigidBot/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 //#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/SCARA/Configuration.h

@@ -217,11 +217,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 3  // (seconds)
 #define TEMP_HYSTERESIS 2       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/TAZ4/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/WITBOX/Configuration.h

@@ -195,11 +195,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/delta/generic/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -198,11 +198,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -215,11 +215,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/makibox/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.