Msq001
6 years ago
committed by
Scott Lahteine
Scott Lahteine
4 changed files with 191 additions and 5 deletions
@ -0,0 +1,183 @@ |
|||
/**
|
|||
* Marlin 3D Printer Firmware |
|||
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|||
* |
|||
* Based on Sprinter and grbl. |
|||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm |
|||
* |
|||
* This program is free software: you can redistribute it and/or modify |
|||
* it under the terms of the GNU General Public License as published by |
|||
* the Free Software Foundation, either version 3 of the License, or |
|||
* (at your option) any later version. |
|||
* |
|||
* This program is distributed in the hope that it will be useful, |
|||
* but WITHOUT ANY WARRANTY; without even the implied warranty of |
|||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
|||
* GNU General Public License for more details. |
|||
* |
|||
* You should have received a copy of the GNU General Public License |
|||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|||
* |
|||
*/ |
|||
#pragma once |
|||
|
|||
#ifndef TARGET_STM32F1 |
|||
#error "Oops! Select an STM32F1 board in 'Tools > Board.'" |
|||
#endif |
|||
|
|||
#define BOARD_NAME "BIGTREE SKR E3 DIP V1.0" |
|||
|
|||
// Release PB3/PB4 (TMC_SW Pins) from JTAG pins
|
|||
#define DISABLE_JTAG |
|||
|
|||
// Ignore temp readings during development.
|
|||
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
|||
|
|||
//
|
|||
// Servos
|
|||
//
|
|||
#define SERVO0_PIN PA1 |
|||
|
|||
//
|
|||
// Limit Switches
|
|||
//
|
|||
#define X_STOP_PIN PC1 |
|||
#define Y_STOP_PIN PC0 |
|||
#define Z_STOP_PIN PC15 |
|||
|
|||
//
|
|||
// Z Probe must be this pin
|
|||
//
|
|||
#define Z_MIN_PROBE_PIN PC14 |
|||
|
|||
//
|
|||
// Filament Runout Sensor
|
|||
//
|
|||
#ifndef FIL_RUNOUT_PIN |
|||
#define FIL_RUNOUT_PIN PC2 |
|||
#endif |
|||
|
|||
//
|
|||
// Steppers
|
|||
//
|
|||
#define X_ENABLE_PIN PC7 |
|||
#define X_STEP_PIN PC6 |
|||
#define X_DIR_PIN PB15 |
|||
#ifndef X_CS_PIN |
|||
#define X_CS_PIN PC10 |
|||
#endif |
|||
|
|||
#define Y_ENABLE_PIN PB14 |
|||
#define Y_STEP_PIN PB13 |
|||
#define Y_DIR_PIN PB12 |
|||
#ifndef Y_CS_PIN |
|||
#define Y_CS_PIN PC11 |
|||
#endif |
|||
|
|||
#define Z_ENABLE_PIN PB11 |
|||
#define Z_STEP_PIN PB10 |
|||
#define Z_DIR_PIN PB2 |
|||
#ifndef Z_CS_PIN |
|||
#define Z_CS_PIN PC12 |
|||
#endif |
|||
|
|||
#define E0_ENABLE_PIN PB1 |
|||
#define E0_STEP_PIN PB0 |
|||
#define E0_DIR_PIN PC5 |
|||
#ifndef E0_CS_PIN |
|||
#define E0_CS_PIN PD2 |
|||
#endif |
|||
|
|||
//
|
|||
// Software SPI pins for TMC2130 stepper drivers
|
|||
//
|
|||
#if ENABLED(TMC_USE_SW_SPI) |
|||
#ifndef TMC_SW_MOSI |
|||
#define TMC_SW_MOSI PB5 |
|||
#endif |
|||
#ifndef TMC_SW_MISO |
|||
#define TMC_SW_MISO PB4 |
|||
#endif |
|||
#ifndef TMC_SW_SCK |
|||
#define TMC_SW_SCK PB3 |
|||
#endif |
|||
#endif |
|||
|
|||
#if HAS_TMC220x |
|||
/**
|
|||
* TMC2208/TMC2209 stepper drivers |
|||
* |
|||
* Hardware serial communication ports. |
|||
* If undefined software serial is used according to the pins below |
|||
*/ |
|||
//#define X_HARDWARE_SERIAL Serial1
|
|||
//#define Y_HARDWARE_SERIAL Serial1
|
|||
//#define Z_HARDWARE_SERIAL Serial1
|
|||
//#define E0_HARDWARE_SERIAL Serial1
|
|||
|
|||
//
|
|||
// Software serial
|
|||
//
|
|||
#define X_SERIAL_TX_PIN PC10 |
|||
#define X_SERIAL_RX_PIN PC10 |
|||
|
|||
#define Y_SERIAL_TX_PIN PC11 |
|||
#define Y_SERIAL_RX_PIN PC11 |
|||
|
|||
#define Z_SERIAL_TX_PIN PC12 |
|||
#define Z_SERIAL_RX_PIN PC12 |
|||
|
|||
#define E0_SERIAL_TX_PIN PD2 |
|||
#define E0_SERIAL_RX_PIN PD2 |
|||
|
|||
#endif |
|||
|
|||
//
|
|||
// Temperature Sensors
|
|||
//
|
|||
#define TEMP_0_PIN PA0 // Analog Input
|
|||
#define TEMP_BED_PIN PC3 // Analog Input
|
|||
|
|||
//
|
|||
// Heaters / Fans
|
|||
//
|
|||
#define HEATER_0_PIN PC8 // EXTRUDER
|
|||
#define HEATER_BED_PIN PC9 // BED
|
|||
#define FAN_PIN PA8 |
|||
|
|||
//
|
|||
// USB connect control
|
|||
//
|
|||
#define USB_CONNECT PC13 |
|||
#define USB_CONNECT_INVERTING false |
|||
|
|||
#define SD_DETECT_PIN PC4 |
|||
|
|||
/**
|
|||
* _____ |
|||
* 5V | · · | GND |
|||
* (LCD_EN) PB7 | · · | PB8 (LCD_RS) |
|||
* (LCD_D4) PB9 | · · | PA10 (BTN_EN2) |
|||
* RESET | · · | PA9 (BTN_EN1) |
|||
* (BTN_ENC) PB6 | · · | PA15 (BEEPER) |
|||
* ----- |
|||
* EXP1 |
|||
*/ |
|||
#if HAS_SPI_LCD |
|||
#define BEEPER_PIN PA15 |
|||
#define BTN_ENC PB6 |
|||
|
|||
#if ENABLED(CR10_STOCKDISPLAY) |
|||
#define LCD_PINS_RS PB8 |
|||
|
|||
#define BTN_EN1 PA9 |
|||
#define BTN_EN2 PA10 |
|||
|
|||
#define LCD_PINS_ENABLE PB7 |
|||
#define LCD_PINS_D4 PB9 |
|||
|
|||
#else |
|||
#error "Only CR10_STOCKDISPLAY is currently supported on the BIGTREE_SKR_E3_DIP." |
|||
#endif |
|||
|
|||
#endif // HAS_SPI_LCD
|
|||
Loading…
Reference in new issue