Browse Source

Add RepRapDiscount Full Graphic Smart Controller support to MIGHTYBOARD REVE

pull/1/head
Paweł Stawicki 8 years ago
committed by Scott Lahteine
parent
commit
652bedfa18
  1. 131
      Marlin/pins_MIGHTYBOARD_REVE.h

131
Marlin/pins_MIGHTYBOARD_REVE.h

@ -129,6 +129,9 @@
#define THERMO_CS1 5 // E3
#define THERMO_CS2 2 // E4
#define MAX6675_SS THERMO_CS1
#define MAX6675_SCK_PIN THERMO_SCK_PIN
#define MAX6675_DO_PIN THERMO_DO_PIN
//
// Augmentation for auto-assigning plugs
//
@ -137,7 +140,7 @@
// With no heated bed, an additional 24V fan is possible.
//
#define MOSFET_A_PIN 6 // H3
#define MOSFET_B_PIN 9 // B5
#define MOSFET_B_PIN 11 // B5
#define MOSFET_C_PIN 45 // L4
#define MOSFET_D_PIN 44 // L5
@ -181,8 +184,8 @@
//
// Extruder Auto Fan Pins
//
#define EXTRUDER_0_AUTO_FAN 7 // H4
#define EXTRUDER_1_AUTO_FAN 12 // B6
#define ORIG_E0_AUTO_FAN_PIN 7 // H4
#define ORIG_E1_AUTO_FAN_PIN 12 // B6
//
// Misc. Functions
@ -194,29 +197,117 @@
//
// LCD / Controller
//
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#define LCD_PINS_RS 33 // C4, LCD-STROBE
#define LCD_PINS_ENABLE 72 // J2, LEFT
#define LCD_PINS_D4 35 // C2, LCD-CLK
#define LCD_PINS_D5 32 // C5, RLED
#define LCD_PINS_D6 34 // C3, LCD-DATA
#define LCD_PINS_D7 31 // C6, GLED
#define BTN_EN2 75 // J4, UP
#define BTN_EN1 73 // J3, DOWN
//STOP button connected as KILL_PIN
#define KILL_PIN 14 // J1, RIGHT
//KILL - not connected
#define BEEPER_PIN 8 // H5, SD_WP
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
//on board leds
#define STAT_LED_RED_LED SERVO0_PIN // C1 (1280-EX1, DEBUG2)
#define STAT_LED_BLUE_PIN SERVO1_PIN // C0 (1280-EX2, DEBUG3)
#else
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BEEPER_PIN 4 // G5
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#define BEEPER_PIN 4 // G5
#define STAT_LED_RED_PIN 32 // C5
#define STAT_LED_BLUE_PIN 31 // C6 (Actually green)
#endif
#define STAT_LED_RED 32 // C5
#define STAT_LED_BLUE 31 // C6 (Actually green)
//
// SD Card
//
#define SDSS 53 // B0
#define SD_DETECT_PIN 30 // C7
#define SD_DETECT_PIN 9 // H6
#define MAX_PIN THERMO_SCK_PIN
//check if all pins are defined in mega/pins_arduino.h
#include <Arduino.h>
static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"
"to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below");
/* in [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h
change:
#define NUM_DIGITAL_PINS 70
to:
#define NUM_DIGITAL_PINS 80
to digital_pin_to_port_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
....
PG , // PG 4 ** 70 **
PG , // PG 3 ** 71 **
PJ , // PJ 2 ** 72 **
PJ , // PJ 3 ** 73 **
PJ , // PJ 7 ** 74 **
PJ , // PJ 4 ** 75 **
PJ , // PJ 5 ** 76 **
PJ , // PJ 6 ** 77 **
PE , // PE 2 ** 78 **
PE , // PE 6 ** 79 **
};
to digital_pin_to_bit_mask_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
....
_BV( 4 ) , // PG 4 ** 70 **
_BV( 3 ) , // PG 3 ** 71 **
_BV( 2 ) , // PJ 2 ** 72 **
_BV( 3 ) , // PJ 3 ** 73 **
_BV( 7 ) , // PJ 7 ** 74 **
_BV( 4 ) , // PJ 4 ** 75 **
_BV( 5 ) , // PJ 5 ** 76 **
_BV( 6 ) , // PJ 6 ** 77 **
_BV( 2 ) , // PE 2 ** 78 **
_BV( 6 ) , // PE 6 ** 79 **
};
to digital_pin_to_timer_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
....
NOT_ON_TIMER , // PG 4 ** 70 **
NOT_ON_TIMER , // PG 3 ** 71 **
NOT_ON_TIMER , // PJ 2 ** 72 **
NOT_ON_TIMER , // PJ 3 ** 73 **
NOT_ON_TIMER , // PJ 7 ** 74 **
NOT_ON_TIMER , // PJ 4 ** 75 **
NOT_ON_TIMER , // PJ 5 ** 76 **
NOT_ON_TIMER , // PJ 6 ** 77 **
NOT_ON_TIMER , // PE 2 ** 78 **
NOT_ON_TIMER , // PE 6 ** 79 **
};
*/

Loading…
Cancel
Save