andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Config file cleanup for Z_PROBE_AND_ENDSTOP support.

pull/1/head
Chris Roadfeldt 10 years ago
parent
324c14943b
commit
6125124d6c
1 changed files with 14 additions and 23 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Unified View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 37
      Marlin/Configuration.h

37
Marlin/Configuration.h
View File

@ -309,6 +309,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
#define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN #define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN #define ENDSTOPPULLUP_ZMIN
#define ENDSTOPPULLUP_ZPROBE
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@ -317,9 +318,15 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
//#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
// activated Z_PROBE_AND_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
// this has no effect.
//#define DISABLE_Z_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0 #define X_ENABLE_ON 0
@ -484,33 +491,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
#endif #endif
// Z Probe and Z endstop support // Seaparte concurrent Z Probe and Z min endstop support
// Added by Chris Roadfeldt 3-28-2015 // Added by Chris Roadfeldt 3-28-2015
// If you have a Z Probe in addition to endstop(s) for Z Homing, uncomment the #define Z_PROBE_AND_ENDSTOP line below and configure Z Probe settings. // If you have a Z Probe in addition to a Z min endstop, uncomment the #define Z_PROBE_AND_ENDSTOP line below and configure Z Probe settings.
// Only use this if you have both a Z PROBE and Z HOMING ENDSTOP(S). If you are using Z_SAFE_HOMING above, then you probably don't need this unless you want to make use of // Only use this if you have both a Z PROBE and Z Min ENDSTOP.
// a non-default pin for your Z Probe. // Note: It's expected that your Z Probe triggers in the direction towards your bed.
// Note: It's expected that your Z Probe triggers in the direction towards your bed. If your Z Probe does not trigger when traveling towards you bed, it will trigger when it's moving // In order to use this, you must have a Z_PROBE_PIN defined in the pins.h file for your control board.
// away from the bed. // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board for the signal.
// #define Z_PROBE_AND_ENDSTOP
#ifdef Z_PROBE_AND_ENDSTOP
// As of 3-28-2015, there are NO Z Probe pins defined in any board config files.
// Z_PROBE_PIN is for the signal pin only. RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board for the signal.
// The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. The Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works. // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. The Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
// D32 is currently selected in the RAMPS 1.3/1.4 pin file. Update the pins.h file for your control board to make use of this. Not doing so nullifies Z_PROBE_AND_ENDSTOP // D32 is currently selected in the RAMPS 1.3/1.4 pin file. Update the pins.h file for your control board to make use of this. Not doing so nullifies Z_PROBE_AND_ENDSTOP
// WARNING: Setting the wrong pin may have unexpected and disastrous outcomes. Use with caution and do your homework. // WARNING: Setting the wrong pin may have unexpected and disastrous outcomes. Use with caution and do your homework.
// #define Z_PROBE_AND_ENDSTOP
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
// The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
#define ENDSTOPPULLUP_ZPROBE
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
// #define DISABLE_Z_PROBE_ENDSTOP
#endif
#endif // ENABLE_AUTO_BED_LEVELING #endif // ENABLE_AUTO_BED_LEVELING

Write Preview
Loading…
Cancel
Save