Followup for MESH_EDIT_GFX_OVERLAY

.travis.yml

@@ -292,7 +292,7 @@ script:
   #
   - use_example_configs delta/generic
   - opt_disable DISABLE_MIN_ENDSTOPS
-  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2
+  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY
   - build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}
   #
   # Delta Config (FLSUN AC because it's complex)

Marlin/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/default/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/default/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -899,7 +899,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -973,6 +972,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -998,7 +998,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1096,6 +1095,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -885,7 +885,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -959,6 +958,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -612,6 +612,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -870,7 +870,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -944,6 +943,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -880,7 +880,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -954,6 +953,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -607,6 +607,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -641,7 +645,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -870,7 +870,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -944,6 +943,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -878,7 +878,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -952,6 +951,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -889,7 +889,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -963,6 +962,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Felix/Configuration.h

@@ -861,7 +861,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -935,6 +934,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -861,7 +861,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -935,6 +934,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -876,7 +876,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -950,6 +949,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y 10

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -894,7 +894,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -968,6 +967,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -907,7 +907,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -981,6 +980,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -604,6 +604,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -638,7 +642,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -880,7 +880,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -954,6 +953,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -612,6 +612,10 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
+
   // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined.
   #if ENABLED(VIKI2) || ENABLED(miniVIKI)
     #define DOGLCD_SCK SCK_PIN
@@ -652,7 +656,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -877,7 +877,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -951,6 +950,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/SCARA/Configuration.h

@@ -891,7 +891,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -965,6 +964,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -882,7 +882,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -956,6 +955,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -910,7 +910,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -984,6 +983,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -599,6 +599,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -633,7 +637,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -935,7 +935,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1009,6 +1008,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -909,7 +909,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -983,6 +982,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -618,6 +618,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -652,7 +656,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1009,7 +1009,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1085,6 +1084,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1009,7 +1009,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1079,6 +1078,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -996,7 +996,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1073,6 +1072,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -999,7 +999,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1076,6 +1075,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -999,7 +999,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1076,6 +1075,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

@@ -617,6 +617,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -651,7 +655,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -1008,7 +1008,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1085,6 +1084,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -893,7 +893,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 #define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -967,6 +966,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 45             // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/makibox/Configuration.h

@@ -882,7 +882,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -956,6 +955,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -874,7 +874,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -948,6 +947,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/wt150/Configuration.h

@@ -884,7 +884,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -958,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/inc/SanityCheck.h

@@ -219,6 +219,10 @@
   #error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
 #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X)  || defined(UBL_MESH_MAX_Y)
   #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
+#elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
+  #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
+#elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
+  #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
 #endif
 
 /**
@@ -760,9 +764,6 @@ static_assert(1 >= 0
     static_assert(WITHIN(UBL_PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_2_Y can't be reached by the Z probe.");
     static_assert(WITHIN(UBL_PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_3_Y can't be reached by the Z probe.");
   #endif
-  #if ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY) && !ENABLED(DOGLCD)
-    #error "ENABLE_MESH_EDIT_GFX_OVERLAY requires a DOGLCD."
-  #endif
 
 #elif OLDSCHOOL_ABL
 
@@ -832,6 +833,10 @@ static_assert(1 >= 0
   #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL."
 #endif
 
+#if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD))
+  #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD."
+#endif
+
 /**
  * LCD_BED_LEVELING requirements
  */

Marlin/src/lcd/dogm/dogm_bitmaps.h

@@ -420,7 +420,7 @@
     };
   #endif // Extruders
 #endif // HAS_TEMP_BED
-#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
+#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
   const unsigned char cw_bmp[] PROGMEM = { //AVR-GCC, WinAVR
     0x07,0xf8,0x00, // 000001111111100000000000
     0x0c,0x0c,0x00, // 000011000000110000000000
@@ -510,4 +510,4 @@
     0x1E,0x00, // 0001111000000000
     0x0C,0x00  // 0000110000000000
   };
-#endif // BABYSTEP_ZPROBE_GFX_OVERLAY || ENABLE_MESH_EDIT_GFX_OVERLAY
+#endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY

Marlin/src/lcd/ultralcd.cpp

@@ -1035,46 +1035,21 @@ void kill_screen(const char* lcd_msg) {
     }
   #endif
 
-  #if ENABLED(BABYSTEPPING)
+  #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
-
-    void _lcd_babystep(const AxisEnum axis, const char* msg) {
-      if (lcd_clicked) { return lcd_goto_previous_menu_no_defer(); }
-      ENCODER_DIRECTION_NORMAL();
-      if (encoderPosition) {
-        const int16_t babystep_increment = (int32_t)encoderPosition * (BABYSTEP_MULTIPLICATOR);
-        encoderPosition = 0;
-        lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
-        thermalManager.babystep_axis(axis, babystep_increment);
-        babysteps_done += babystep_increment;
-      }
-      if (lcdDrawUpdate)
-        lcd_implementation_drawedit(msg, ftostr43sign(planner.steps_to_mm[axis] * babysteps_done));
-    }
-
-    #if ENABLED(BABYSTEP_XY)
-      void _lcd_babystep_x() { _lcd_babystep(X_AXIS, PSTR(MSG_BABYSTEP_X)); }
-      void _lcd_babystep_y() { _lcd_babystep(Y_AXIS, PSTR(MSG_BABYSTEP_Y)); }
-      void lcd_babystep_x() { lcd_goto_screen(_lcd_babystep_x); babysteps_done = 0; defer_return_to_status = true; }
-      void lcd_babystep_y() { lcd_goto_screen(_lcd_babystep_y); babysteps_done = 0; defer_return_to_status = true; }
-    #endif
-
-    #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
 
-      void _lcd_zoffset_overlay_gfx(const float in_zoffset) {
+    void _lcd_zoffset_overlay_gfx(const float zvalue) {
       // Determine whether the user is raising or lowering the nozzle.
-        int8_t dir = 0;
+      static int8_t dir;
-        static float old_zprobe_zoffset = 0;
+      static float old_zvalue;
-        if (in_zoffset != old_zprobe_zoffset) {
+      if (zvalue != old_zvalue) {
-          dir = (in_zoffset > old_zprobe_zoffset) ? 1 : (in_zoffset == 0) ? 0 : -1;
+        dir = zvalue ? zvalue < old_zvalue ? -1 : 1 : 0;
-          old_zprobe_zoffset = in_zoffset;
+        old_zvalue = zvalue;
       }
 
-        #if ENABLED(BABYSTEP_ZPROBE_GFX_REVERSE)
+      #if ENABLED(OVERLAY_GFX_REVERSE)
-          const unsigned char *rot_up   = ccw_bmp;
+        const unsigned char *rot_up = ccw_bmp, *rot_down = cw_bmp;
-          const unsigned char *rot_down = cw_bmp;
       #else
-          const unsigned char *rot_up   = cw_bmp;
+        const unsigned char *rot_up = cw_bmp, *rot_down = ccw_bmp;
-          const unsigned char *rot_down = ccw_bmp;
       #endif
 
       #if ENABLED(USE_BIG_EDIT_FONT)
@@ -1096,7 +1071,30 @@ void kill_screen(const char* lcd_msg) {
       }
     }
 
-    #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || ENABLE_MESH_EDIT_GFX_OVERLAY
+  #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY
+
+  #if ENABLED(BABYSTEPPING)
+
+    void _lcd_babystep(const AxisEnum axis, const char* msg) {
+      if (lcd_clicked) { return lcd_goto_previous_menu_no_defer(); }
+      ENCODER_DIRECTION_NORMAL();
+      if (encoderPosition) {
+        const int16_t babystep_increment = (int32_t)encoderPosition * (BABYSTEP_MULTIPLICATOR);
+        encoderPosition = 0;
+        lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
+        thermalManager.babystep_axis(axis, babystep_increment);
+        babysteps_done += babystep_increment;
+      }
+      if (lcdDrawUpdate)
+        lcd_implementation_drawedit(msg, ftostr43sign(planner.steps_to_mm[axis] * babysteps_done));
+    }
+
+    #if ENABLED(BABYSTEP_XY)
+      void _lcd_babystep_x() { _lcd_babystep(X_AXIS, PSTR(MSG_BABYSTEP_X)); }
+      void _lcd_babystep_y() { _lcd_babystep(Y_AXIS, PSTR(MSG_BABYSTEP_Y)); }
+      void lcd_babystep_x() { lcd_goto_screen(_lcd_babystep_x); babysteps_done = 0; defer_return_to_status = true; }
+      void lcd_babystep_y() { lcd_goto_screen(_lcd_babystep_y); babysteps_done = 0; defer_return_to_status = true; }
+    #endif
 
     #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
 
@@ -1157,7 +1155,7 @@ void kill_screen(const char* lcd_msg) {
 
       if (lcdDrawUpdate)
         lcd_implementation_drawedit(msg, ftostr43sign(mesh_edit_value));
-        #if ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
+        #if ENABLED(MESH_EDIT_GFX_OVERLAY)
           _lcd_zoffset_overlay_gfx(mesh_edit_value);
         #endif
     }
@@ -1194,7 +1192,6 @@ void kill_screen(const char* lcd_msg) {
 
   #endif // AUTO_BED_LEVELING_UBL
 
-
   /**
    * Watch temperature callbacks
    */