andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

UBL G29: replace 'O' with 'T' 

Since we already used 'T' for `G29` Topology Report in the past, and since 'T' is available…
pull/1/head
Scott Lahteine 8 years ago
parent
091f94a6bf
commit
56e2e331ed
1 changed files with 16 additions and 18 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 34
      Marlin/ubl_G29.cpp

34
Marlin/ubl_G29.cpp
View File

@ -107,10 +107,10 @@
*
* I # Invalidate Invalidate specified number of Mesh Points. The nozzle location is used unless
* the X and Y parameter are used. If no number is specified, only the closest Mesh
* point to the location is invalidated. The M parameter is available as well to produce
* point to the location is invalidated. The 'T' parameter is also available to produce
* a map after the operation. This command is useful to invalidate a portion of the
* Mesh so it can be adjusted using other tools in the Unified Bed Leveling System. When
* attempting to invalidate an isolated bad point in the mesh, the M option will indicate
* attempting to invalidate an isolated bad point in the mesh, the 'T' option will indicate
* where the nozzle is positioned in the Mesh with (#). You can move the nozzle around on
* the bed and use this feature to select the center of the area (or cell) you want to
* invalidate.
@ -126,14 +126,6 @@
* L # Load * Load Mesh from the specified location in the EEPROM. Set this location as activated
* for subsequent Load and Store operations.
*
* O Map * Display the Mesh Map Topology.
* The parameter can be specified alone (ie. G29 O) or in combination with many of the
* other commands. The Mesh Map option works with all of the Phase
* commands (ie. G29 P4 R 5 X 50 Y100 C -.1 O) The Map parameter can also of a Map Type
* specified. A map type of 0 is the default is user readable. A map type of 1 can
* be specified and is suitable to Cut & Paste into Excel to allow graphing of the user's
* mesh.
*
* The P or Phase commands are used for the bulk of the work to setup a Mesh. In general, your Mesh will
* start off being initialized with a G29 P0 or a G29 P1. Further refinement of the Mesh happens with
* each additional Phase that processes it.
@ -173,7 +165,7 @@
* area you are manually probing. Note that the command tries to start you in a corner
* of the bed where movement will be predictable. You can force the location to be used in
* the distance calculations by using the X and Y parameters. You may find it is helpful to
* print out a Mesh Map (G29 O) to understand where the mesh is invalidated and where
* print out a Mesh Map (G29 T) to understand where the mesh is invalidated and where
* the nozzle will need to move in order to complete the command. The C parameter is
* available on the Phase 2 command also and indicates the search for points to measure should
* be done based on the current location of the nozzle.
@ -189,7 +181,7 @@
* to get it to grasp the shim with the same force as when you measured the thickness of the
* shim at the start of the command.
*
* Phase 2 allows the O (Map) parameter to be specified. This helps the user see the progression
* Phase 2 allows the T (Map) parameter to be specified. This helps the user see the progression
* of the Mesh being built.
*
* P3 Phase 3 Fill the unpopulated regions of the Mesh with a fixed value. There are two different paths the
@ -263,6 +255,12 @@
* at a later date. The GCode output can be saved and later replayed by the host software
* to reconstruct the current mesh on another machine.
*
* T Topology Display the Mesh Map Topology.
* 'T' can be used alone (e.g., G29 T) or in combination with some of the other commands.
* This option works with all Phase commands (e.g., G29 P4 R 5 X 50 Y100 C -.1 O)
* This parameter can also specify a Map Type. T0 (the default) is user-readable. T1 can
* is suitable to paste into a spreadsheet for a 3D graph of the mesh.
*
* U Unlevel Perform a probe of the outer perimeter to assist in physically leveling unlevel beds.
* Only used for G29 P1 O U It will speed up the probing of the edge of the bed. This
* is useful when the entire bed does not need to be probed because it will be adjusted.
@ -381,7 +379,7 @@
if (code_seen('J')) {
if (grid_size!=0) { // if not 0 it is a normal n x n grid being probed
ubl.save_ubl_active_state_and_disable();
ubl.tilt_mesh_based_on_probed_grid(code_seen('O'));
ubl.tilt_mesh_based_on_probed_grid(code_seen('T'));
ubl.restore_ubl_active_state_and_leave();
} else { // grid_size==0 which means a 3-Point leveling has been requested
float z1 = probe_pt(LOGICAL_X_POSITION(UBL_PROBE_PT_1_X), LOGICAL_Y_POSITION(UBL_PROBE_PT_1_Y), false, g29_verbose_level),
@ -438,7 +436,7 @@
SERIAL_PROTOCOLLNPGM(").\n");
}
ubl.probe_entire_mesh(x_pos + X_PROBE_OFFSET_FROM_EXTRUDER, y_pos + Y_PROBE_OFFSET_FROM_EXTRUDER,
code_seen('O'), code_seen('E'), code_seen('U'));
code_seen('T'), code_seen('E'), code_seen('U'));
break;
case 2: {
@ -487,7 +485,7 @@
return;
}
manually_probe_remaining_mesh(x_pos, y_pos, height, card_thickness, code_seen('O'));
manually_probe_remaining_mesh(x_pos, y_pos, height, card_thickness, code_seen('T'));
SERIAL_PROTOCOLLNPGM("G29 P2 finished.");
} break;
@ -523,7 +521,7 @@
//
// Fine Tune (i.e., Edit) the Mesh
//
fine_tune_mesh(x_pos, y_pos, code_seen('O'));
fine_tune_mesh(x_pos, y_pos, code_seen('T'));
break;
case 5: ubl.find_mean_mesh_height(); break;
@ -601,7 +599,7 @@
SERIAL_PROTOCOLLNPGM("Done.\n");
}
if (code_seen('O'))
if (code_seen('T'))
ubl.display_map(code_has_value() ? code_value_int() : 0);
/*
@ -1112,7 +1110,7 @@
}
#endif
map_type = code_seen('O') && code_has_value() ? code_value_int() : 0;
map_type = code_seen('T') && code_has_value() ? code_value_int() : 0;
if (!WITHIN(map_type, 0, 1)) {
SERIAL_PROTOCOLLNPGM("Invalid map type.\n");
return UBL_ERR;

Write Preview
Loading…
Cancel
Save