andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

SPINDLE/LASER implementation

pull/1/head
Scott Lahteine 8 years ago
committed by Scott Lahteine
parent
ffe0e2d19a
commit
55a87da036
1 changed files with 141 additions and 0 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 141
      Marlin/Marlin_main.cpp

141
Marlin/Marlin_main.cpp
View File

@ -73,6 +73,9 @@
*
* M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
* M1 - Same as M0
* M3 - Turn laser/spindle on, set spindle/laser speed/power, set rotation to clockwise
* M4 - Turn laser/spindle on, set spindle/laser speed/power, set rotation to counter-clockwise
* M5 - Turn laser/spindle off
* M17 - Enable/Power all stepper motors
* M18 - Disable all stepper motors; same as M84
* M20 - List SD card. (Requires SDSUPPORT)
@ -5611,6 +5614,121 @@ inline void gcode_G92() {
#endif // HAS_RESUME_CONTINUE
#if ENABLED(SPINDLE_LASER_ENABLE)
/**
* M3: Spindle Clockwise
* M4: Spindle Counter-clockwise
*
* S0 turns off spindle.
*
* If no speed PWM output is defined then M3/M4 just turns it on.
*
* At least 12.8KHz (50Hz * 256) is needed for spindle PWM.
* Hardware PWM is required. ISRs are too slow.
*
* NOTE: WGM for timers 3, 4, and 5 must be either Mode 1 or Mode 5.
* No other settings give a PWM signal that goes from 0 to 5 volts.
*
* The system automatically sets WGM to Mode 1, so no special
* initialization is needed.
*
* WGM bits for timer 2 are automatically set by the system to
* Mode 1. This produces an acceptable 0 to 5 volt signal.
* No special initialization is needed.
*
* NOTE: A minimum PWM frequency of 50 Hz is needed. All prescaler
* factors for timers 2, 3, 4, and 5 are acceptable.
*
* SPINDLE_LASER_ENABLE_PIN needs an external pullup or it may power on
* the spindle/laser during power-up or when connecting to the host
* (usually goes through a reset which sets all I/O pins to tri-state)
*
* PWM duty cycle goes from 0 (off) to 255 (always on).
*/
// Wait for spindle to come up to speed
inline void delay_for_power_up() {
refresh_cmd_timeout();
while (PENDING(millis(), SPINDLE_LASER_POWERUP_DELAY + previous_cmd_ms)) idle();
}
// Wait for spindle to stop turning
inline void delay_for_power_down() {
refresh_cmd_timeout();
while (PENDING(millis(), SPINDLE_LASER_POWERDOWN_DELAY + previous_cmd_ms + 1)) idle();
}
/**
* ocr_val_mode() is used for debugging and to get the points needed to compute the RPM vs ocr_val line
*
* it accepts inputs of 0-255
*/
inline void ocr_val_mode() {
uint8_t spindle_laser_power = code_value_byte();
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
if (SPINDLE_LASER_PWM_INVERT) spindle_laser_power = 255 - spindle_laser_power;
analogWrite(SPINDLE_LASER_PWM_PIN, spindle_laser_power);
}
inline void gcode_M3_M4(bool is_M3) {
stepper.synchronize(); // wait until previous movement commands (G0/G0/G2/G3) have completed before playing with the spindle
#if SPINDLE_DIR_CHANGE
const bool rotation_dir = (is_M3 && !SPINDLE_INVERT_DIR || !is_M3 && SPINDLE_INVERT_DIR) ? HIGH : LOW;
if (SPINDLE_STOP_ON_DIR_CHANGE \
&& READ(SPINDLE_LASER_ENABLE_PIN) == SPINDLE_LASER_ENABLE_INVERT \
&& READ(SPINDLE_DIR_PIN) != rotation_dir
) {
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off
delay_for_power_down();
}
digitalWrite(SPINDLE_DIR_PIN, rotation_dir);
#endif
/**
* Our final value for ocr_val is an unsigned 8 bit value between 0 and 255 which usually means uint8_t.
* Went to uint16_t because some of the uint8_t calculations would sometimes give 1000 0000 rather than 1111 1111.
* Then needed to AND the uint16_t result with 0x00FF to make sure we only wrote the byte of interest.
*/
#if ENABLED(SPINDLE_LASER_PWM)
if (code_seen('O')) ocr_val_mode();
else {
const float spindle_laser_power = code_seen('S') ? code_value_float() : 0;
if (spindle_laser_power == 0) {
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off (active low)
delay_for_power_down();
}
else {
int16_t ocr_val = (spindle_laser_power - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // convert RPM to PWM duty cycle
NOMORE(ocr_val, 255); // limit to max the Atmel PWM will support
if (spindle_laser_power <= SPEED_POWER_MIN)
ocr_val = (SPEED_POWER_MIN - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // minimum setting
if (spindle_laser_power >= SPEED_POWER_MAX)
ocr_val = (SPEED_POWER_MAX - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // limit to max RPM
if (SPINDLE_LASER_PWM_INVERT) ocr_val = 255 - ocr_val;
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
analogWrite(SPINDLE_LASER_PWM_PIN, ocr_val & 0xFF); // only write low byte
delay_for_power_up();
}
}
#else
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low) if spindle speed option not enabled
delay_for_power_up();
#endif
}
/**
* M5 turn off spindle
*/
inline void gcode_M5() {
stepper.synchronize();
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT);
delay_for_power_down();
}
#endif // SPINDLE_LASER_ENABLE
/**
* M17: Enable power on all stepper motors
*/
@ -5626,6 +5744,7 @@ inline void gcode_M17() {
#endif
#if ENABLED(PARK_HEAD_ON_PAUSE)
float resume_position[XYZE];
bool move_away_flag = false;
@ -9946,6 +10065,17 @@ void process_next_command() {
break;
#endif // ULTIPANEL
#if ENABLED(SPINDLE_LASER_ENABLE)
case 3:
gcode_M3_M4(true); // M3: turn spindle/laser on, set laser/spindle power/speed, set rotation direction CW
break; // synchronizes with movement commands
case 4:
gcode_M3_M4(false); // M4: turn spindle/laser on, set laser/spindle power/speed, set rotation direction CCW
break; // synchronizes with movement commands
case 5:
gcode_M5(); // M5 - turn spindle/laser off
break; // synchronizes with movement commands
#endif
case 17: // M17: Enable all stepper motors
gcode_M17();
break;
@ -12262,6 +12392,17 @@ void setup() {
update_case_light();
#endif
#if ENABLED(SPINDLE_LASER_ENABLE)
OUT_WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // init spindle to off
#if SPINDLE_DIR_CHANGE
OUT_WRITE(SPINDLE_DIR_PIN, SPINDLE_INVERT_DIR ? 255 : 0); // init rotation to clockwise (M3)
#endif
#if ENABLED(SPINDLE_LASER_PWM)
SET_OUTPUT(SPINDLE_LASER_PWM_PIN);
analogWrite(SPINDLE_LASER_PWM_PIN, SPINDLE_LASER_PWM_INVERT ? 255 : 0); // set to lowest speed
#endif
#endif
#if HAS_BED_PROBE
endstops.enable_z_probe(false);
#endif

Write Preview
Loading…
Cancel
Save