Make nomove=false for toolchange on filament swap (#12739)

Marlin/src/gcode/feature/pause/M600.cpp

@@ -88,7 +88,7 @@ void GcodeSuite::M600() {
       #if ENABLED(DUAL_X_CARRIAGE)
         && dual_x_carriage_mode != DXC_DUPLICATION_MODE && dual_x_carriage_mode != DXC_SCALED_DUPLICATION_MODE
       #endif
-    ) tool_change(target_extruder, 0, true);
+    ) tool_change(target_extruder, 0, false);
   #endif
 
   // Initial retract before move to filament change position
@@ -137,7 +137,7 @@ void GcodeSuite::M600() {
   #if EXTRUDERS > 1
     // Restore toolhead if it was changed
     if (active_extruder_before_filament_change != active_extruder)
-      tool_change(active_extruder_before_filament_change, 0, true);
+      tool_change(active_extruder_before_filament_change, 0, false);
   #endif
 }
 

Marlin/src/gcode/feature/pause/M701_M702.cpp

@@ -71,7 +71,7 @@ void GcodeSuite::M701() {
     // Change toolhead if specified
     uint8_t active_extruder_before_filament_change = active_extruder;
     if (active_extruder != target_extruder)
-      tool_change(target_extruder, 0, true);
+      tool_change(target_extruder, 0, false);
   #endif
 
   // Lift Z axis
@@ -96,7 +96,7 @@ void GcodeSuite::M701() {
   #if EXTRUDERS > 1
     // Restore toolhead if it was changed
     if (active_extruder_before_filament_change != active_extruder)
-      tool_change(active_extruder_before_filament_change, 0, true);
+      tool_change(active_extruder_before_filament_change, 0, false);
   #endif
 
   // Show status screen
@@ -138,7 +138,7 @@ void GcodeSuite::M702() {
     // Change toolhead if specified
     uint8_t active_extruder_before_filament_change = active_extruder;
     if (active_extruder != target_extruder)
-      tool_change(target_extruder, 0, true);
+      tool_change(target_extruder, 0, false);
   #endif
 
   // Lift Z axis
@@ -149,7 +149,7 @@ void GcodeSuite::M702() {
   #if EXTRUDERS > 1 && ENABLED(FILAMENT_UNLOAD_ALL_EXTRUDERS)
     if (!parser.seenval('T')) {
       HOTEND_LOOP() {
-        if (e != active_extruder) tool_change(e, 0, true);
+        if (e != active_extruder) tool_change(e, 0, false);
         unload_filament(-fc_settings[e].unload_length, true, ADVANCED_PAUSE_MODE_UNLOAD_FILAMENT);
       }
     }
@@ -170,7 +170,7 @@ void GcodeSuite::M702() {
   #if EXTRUDERS > 1
     // Restore toolhead if it was changed
     if (active_extruder_before_filament_change != active_extruder)
-      tool_change(active_extruder_before_filament_change, 0, true);
+      tool_change(active_extruder_before_filament_change, 0, false);
   #endif
 
   // Show status screen