andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

TCNT0 => HAL_timer_get_current_count 

Fix #8710
pull/1/head
Scott Lahteine 7 years ago
parent
b3daf6b5db
commit
4fa65a5c25
3 changed files with 26 additions and 25 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 43
      Marlin/src/module/stepper.cpp
  2. 6
      Marlin/src/module/stepper.h
  3. 2
      Marlin/src/module/temperature.cpp

43
Marlin/src/module/stepper.cpp
View File

@ -118,8 +118,8 @@ volatile uint32_t Stepper::step_events_completed = 0; // The number of step even
constexpr hal_timer_t ADV_NEVER = HAL_TIMER_TYPE_MAX;
hal_timer_t Stepper::nextMainISR = 0,
Stepper::nextAdvanceISR = ADV_NEVER,
Stepper::eISR_Rate = ADV_NEVER;
Stepper::nextAdvanceISR = ADV_NEVER,
Stepper::eISR_Rate = ADV_NEVER;
volatile int Stepper::e_steps[E_STEPPERS];
int Stepper::final_estep_rate,
@ -152,9 +152,10 @@ volatile signed char Stepper::count_direction[NUM_AXIS] = { 1, 1, 1, 1 };
long Stepper::counter_m[MIXING_STEPPERS];
#endif
hal_timer_t Stepper::acc_step_rate; // needed for deceleration start point
uint8_t Stepper::step_loops, Stepper::step_loops_nominal;
hal_timer_t Stepper::OCR1A_nominal;
hal_timer_t Stepper::OCR1A_nominal,
Stepper::acc_step_rate; // needed for deceleration start point
volatile long Stepper::endstops_trigsteps[XYZ];
@ -557,13 +558,13 @@ void Stepper::isr() {
/**
* If a minimum pulse time was specified get the timer 0 value.
*
* TCNT0 has an 8x prescaler, so it increments every 8 cycles.
* On AVR the TCNT0 timer has an 8x prescaler, so it increments every 8 cycles.
* That's every 0.5µs on 16MHz and every 0.4µs on 20MHz.
* 20 counts of TCNT0 -by itself- is a good pulse delay.
* 10µs = 160 or 200 cycles.
*/
#if EXTRA_CYCLES_XYZE > 20
uint32_t pulse_start = HAL_timer_get_current_count(STEP_TIMER_NUM);
hal_timer_t pulse_start = HAL_timer_get_current_count(STEP_TIMER_NUM);
#endif
#if HAS_X_STEP
@ -676,12 +677,12 @@ void Stepper::isr() {
NOMORE(acc_step_rate, current_block->nominal_rate);
// step_rate to timer interval
const hal_timer_t timer = calc_timer(acc_step_rate);
const hal_timer_t interval = calc_timer_interval(acc_step_rate);
SPLIT(timer); // split step into multiple ISRs if larger than ENDSTOP_NOMINAL_OCR_VAL
SPLIT(interval); // split step into multiple ISRs if larger than ENDSTOP_NOMINAL_OCR_VAL
_NEXT_ISR(ocr_val);
acceleration_time += timer;
acceleration_time += interval;
#if ENABLED(LIN_ADVANCE)
@ -693,7 +694,7 @@ void Stepper::isr() {
current_estep_rate[TOOL_E_INDEX] = ((uint32_t)acc_step_rate * current_block->abs_adv_steps_multiplier8) >> 17;
#endif
}
eISR_Rate = adv_rate(e_steps[TOOL_E_INDEX], timer, step_loops);
eISR_Rate = adv_rate(e_steps[TOOL_E_INDEX], interval, step_loops);
#endif // LIN_ADVANCE
}
@ -713,11 +714,11 @@ void Stepper::isr() {
step_rate = current_block->final_rate;
// step_rate to timer interval
const hal_timer_t timer = calc_timer(step_rate);
const hal_timer_t interval = calc_timer_interval(step_rate);
SPLIT(timer); // split step into multiple ISRs if larger than ENDSTOP_NOMINAL_OCR_VAL
SPLIT(interval); // split step into multiple ISRs if larger than ENDSTOP_NOMINAL_OCR_VAL
_NEXT_ISR(ocr_val);
deceleration_time += timer;
deceleration_time += interval;
#if ENABLED(LIN_ADVANCE)
@ -729,7 +730,7 @@ void Stepper::isr() {
current_estep_rate[TOOL_E_INDEX] = ((uint32_t)step_rate * current_block->abs_adv_steps_multiplier8) >> 17;
#endif
}
eISR_Rate = adv_rate(e_steps[TOOL_E_INDEX], timer, step_loops);
eISR_Rate = adv_rate(e_steps[TOOL_E_INDEX], interval, step_loops);
#endif // LIN_ADVANCE
}
@ -754,7 +755,7 @@ void Stepper::isr() {
#ifdef CPU_32_BIT
// Make sure stepper interrupt does not monopolise CPU by adjusting count to give about 8 us room
hal_timer_t stepper_timer_count = HAL_timer_get_count(STEP_TIMER_NUM),
stepper_timer_current_count = HAL_timer_get_current_count(STEP_TIMER_NUM) + 8 * HAL_TICKS_PER_US;
stepper_timer_current_count = HAL_timer_get_current_count(STEP_TIMER_NUM) + 8 * HAL_TICKS_PER_US;
HAL_timer_set_count(STEP_TIMER_NUM, max(stepper_timer_count, stepper_timer_current_count));
#else
NOLESS(OCR1A, TCNT1 + 16);
@ -817,7 +818,7 @@ void Stepper::isr() {
for (uint8_t i = step_loops; i--;) {
#if EXTRA_CYCLES_E > 20
uint32_t pulse_start = TCNT0;
hal_timer_t pulse_start = HAL_timer_get_current_count(STEP_TIMER_NUM);
#endif
START_E_PULSE(0);
@ -836,8 +837,8 @@ void Stepper::isr() {
// For minimum pulse time wait before stopping pulses
#if EXTRA_CYCLES_E > 20
while (EXTRA_CYCLES_E > (uint32_t)(TCNT0 - pulse_start) * (INT0_PRESCALER)) { /* nada */ }
pulse_start = TCNT0;
while (EXTRA_CYCLES_E > (hal_timer_t)(HAL_timer_get_current_count(STEP_TIMER_NUM) - pulse_start) * (STEPPER_TIMER_PRESCALE)) { /* nada */ }
pulse_start = HAL_timer_get_current_count(STEP_TIMER_NUM);
#elif EXTRA_CYCLES_E > 0
DELAY_NOPS(EXTRA_CYCLES_E);
#endif
@ -858,7 +859,7 @@ void Stepper::isr() {
// For minimum pulse time wait before looping
#if EXTRA_CYCLES_E > 20
if (i) while (EXTRA_CYCLES_E > (uint32_t)(TCNT0 - pulse_start) * (INT0_PRESCALER)) { /* nada */ }
if (i) while (EXTRA_CYCLES_E > (hal_timer_t)(HAL_timer_get_current_count(STEP_TIMER_NUM) - pulse_start) * (STEPPER_TIMER_PRESCALE)) { /* nada */ }
#elif EXTRA_CYCLES_E > 0
if (i) DELAY_NOPS(EXTRA_CYCLES_E);
#endif
@ -1297,8 +1298,8 @@ void Stepper::report_positions() {
#define _APPLY_DIR(AXIS, INVERT) AXIS ##_APPLY_DIR(INVERT, true)
#if EXTRA_CYCLES_BABYSTEP > 20
#define _SAVE_START const uint32_t pulse_start = TCNT0
#define _PULSE_WAIT while (EXTRA_CYCLES_BABYSTEP > (uint32_t)(TCNT0 - pulse_start) * (INT0_PRESCALER)) { /* nada */ }
#define _SAVE_START const hal_timer_t pulse_start = HAL_timer_get_current_count(STEP_TIMER_NUM)
#define _PULSE_WAIT while (EXTRA_CYCLES_BABYSTEP > (uint32_t)(HAL_timer_get_current_count(STEP_TIMER_NUM) - pulse_start) * (STEPPER_TIMER_PRESCALE)) { /* nada */ }
#else
#define _SAVE_START NOOP
#if EXTRA_CYCLES_BABYSTEP > 0

6
Marlin/src/module/stepper.h
View File

@ -278,7 +278,7 @@ class Stepper {
private:
FORCE_INLINE static hal_timer_t calc_timer(hal_timer_t step_rate) {
FORCE_INLINE static hal_timer_t calc_timer_interval(hal_timer_t step_rate) {
hal_timer_t timer;
NOMORE(step_rate, MAX_STEP_FREQUENCY);
@ -359,11 +359,11 @@ class Stepper {
deceleration_time = 0;
// step_rate to timer interval
OCR1A_nominal = calc_timer(current_block->nominal_rate);
OCR1A_nominal = calc_timer_interval(current_block->nominal_rate);
// make a note of the number of step loops required at nominal speed
step_loops_nominal = step_loops;
acc_step_rate = current_block->initial_rate;
acceleration_time = calc_timer(acc_step_rate);
acceleration_time = calc_timer_interval(acc_step_rate);
_NEXT_ISR(acceleration_time);
#if ENABLED(LIN_ADVANCE)

2
Marlin/src/module/temperature.cpp
View File

@ -1588,7 +1588,7 @@ void Temperature::set_current_temp_raw() {
/**
* Timer 0 is shared with millies so don't change the prescaler.
*
* This ISR uses the compare method so it runs at the base
* On AVR this ISR uses the compare method so it runs at the base
* frequency (16 MHz / 64 / 256 = 976.5625 Hz), but at the TCNT0 set
* in OCR0B above (128 or halfway between OVFs).
*

Write Preview
Loading…
Cancel
Save