Fix M106 with SINGLENOZZLE

Marlin/src/gcode/temperature/M106_M107.cpp

@@ -25,10 +25,11 @@
 #if FAN_COUNT > 0
 
 #include "../gcode.h"
-#include "../../Marlin.h" // for fan_speed — should move those to Planner
+#include "../../Marlin.h" // for fan_speed
+
+#include "../../module/motion.h"
 
 #if ENABLED(SINGLENOZZLE)
-  #include "../../module/motion.h"
   #include "../../module/tool_change.h"
 #endif
 
@@ -46,36 +47,42 @@
  *           3-255 = Set the speed for use with T2
  */
 void GcodeSuite::M106() {
-  const uint8_t p = parser.byteval('P');
+  const uint8_t p = parser.byteval('P', active_extruder);
-  const uint16_t s = parser.ushortval('S', 255);
+
+  if (p < MIN(EXTRUDERS, FAN_COUNT)) {
+    uint16_t s = parser.ushortval('S', 255);
+    NOMORE(s, 255);
+
+    uint8_t np = p;
 
     #if ENABLED(SINGLENOZZLE)
       if (p != active_extruder) {
-      if (p < EXTRUDERS) singlenozzle_fan_speed[p] = MIN(s, 255U);
+        if (p < EXTRUDERS) singlenozzle_fan_speed[p] = s;
         return;
       }
+      np = 0; // Always use fan index 0 with SINGLENOZZLE
     #endif
 
-  if (p < FAN_COUNT) {
     #if ENABLED(EXTRA_FAN_SPEED)
       const int16_t t = parser.intval('T');
       if (t > 0) {
         switch (t) {
           case 1:
-            fan_speed[p] = old_fan_speed[p];
+            fan_speed[np] = old_fan_speed[np];
             break;
           case 2:
-            old_fan_speed[p] = fan_speed[p];
+            old_fan_speed[np] = fan_speed[np];
-            fan_speed[p] = new_fan_speed[p];
+            fan_speed[np] = new_fan_speed[np];
             break;
           default:
-            new_fan_speed[p] = MIN(t, 255U);
+            new_fan_speed[np] = MIN(t, 255U);
             break;
         }
         return;
       }
     #endif // EXTRA_FAN_SPEED
-    fan_speed[p] = MIN(s, 255U);
+
+    fan_speed[np] = s;
   }
 }
 
@@ -83,7 +90,8 @@ void GcodeSuite::M106() {
  * M107: Fan Off
  */
 void GcodeSuite::M107() {
-  const uint16_t p = parser.ushortval('P');
+  const uint16_t p = parser.byteval('P', active_extruder);
+
   #if ENABLED(SINGLENOZZLE)
     if (p != active_extruder) {
       if (p < EXTRUDERS) singlenozzle_fan_speed[p] = 0;
@@ -91,7 +99,7 @@ void GcodeSuite::M107() {
     }
   #endif
 
-  if (p < FAN_COUNT) fan_speed[p] = 0;
+  if (p < MIN(EXTRUDERS, FAN_COUNT)) fan_speed[p] = 0;
 }
 
 #endif // FAN_COUNT > 0