Browse Source

Update setup() description

vanilla_fb_2.0.x
Scott Lahteine 4 years ago
committed by Scott Lahteine
parent
commit
3bbcfb0185
  1. 116
      Marlin/src/MarlinCore.cpp

116
Marlin/src/MarlinCore.cpp

@ -953,23 +953,92 @@ inline void tmc_standby_setup() {
} }
/** /**
* Marlin entry-point: Set up before the program loop * Marlin Firmware entry-point. Abandon Hope All Ye Who Enter Here.
* - Set up the kill pin, filament runout, power hold, custom user buttons * Setup before the program loop:
* - Start the serial port *
* - Call any special pre-init set for the board
* - Put TMC drivers into Low Power Standby mode
* - Init the serial ports (so setup can be debugged)
* - Set up the kill and suicide pins
* - Prepare (disable) board JTAG and Debug ports
* - Init serial for a connected MKS TFT with WiFi
* - Install Marlin custom Exception Handlers, if set.
* - Init Marlin's HAL interfaces (for SPI, i2c, etc.)
* - Init some optional hardware and features:
* MAX Thermocouple pins
* Duet Smart Effector
* Filament Runout Sensor
* TMC220x Stepper Drivers (Serial)
* PSU control
* Power-loss Recovery
* L64XX Stepper Drivers (SPI)
* Stepper Driver Reset: DISABLE
* TMC Stepper Drivers (SPI)
* Run BOARD_INIT if defined
* ESP WiFi
* - Get the Reset Reason and report it
* - Print startup messages and diagnostics * - Print startup messages and diagnostics
* - Get EEPROM or default settings * - Calibrate the HAL DELAY for precise timing
* - Initialize managers for: * - Init the buzzer, possibly a custom timer
* temperature * - Init more optional hardware:
* planner * Color LED illumination
* watchdog * Neopixel illumination
* stepper * Controller Fan
* photo pin * Creality DWIN LCD (show boot image)
* servos * Tare the Probe if possible
* LCD controller * - Mount the (most likely external) SD Card
* Digipot I2C * - Load settings from EEPROM (or use defaults)
* Z probe sled * - Init the Ethernet Port
* status LEDs * - Init Touch Buttons (for emulated DOGLCD)
* Max7219 * - Adjust the (certainly wrong) current position by the home offset
* - Init the Planner::position (steps) based on current (native) position
* - Initialize more managers and peripherals:
* Temperatures
* Print Job Timer
* Endstops and Endstop Interrupts
* Stepper ISR - Kind of Important!
* Servos
* Servo-based Probe
* Photograph Pin
* Laser/Spindle tool Power / PWM
* Coolant Control
* Bed Probe
* Stepper Driver Reset: ENABLE
* Digipot I2C - Stepper driver current control
* Stepper DAC - Stepper driver current control
* Solenoid (probe, or for other use)
* Home Pin
* Custom User Buttons
* Red/Blue Status LEDs
* Case Light
* Prusa MMU filament changer
* Fan Multiplexer
* Mixing Extruder
* BLTouch Probe
* I2C Position Encoders
* Custom I2C Bus handlers
* Enhanced tools or extruders:
* Switching Extruder
* Switching Nozzle
* Parking Extruder
* Magnetic Parking Extruder
* Switching Toolhead
* Electromagnetic Switching Toolhead
* Watchdog Timer - Also Kind of Important!
* Closed Loop Controller
* - Run Startup Commands, if defined
* - Tell host to close Host Prompts
* - Test Trinamic driver connections
* - Init Prusa MMU2 filament changer
* - Init and test BL24Cxx EEPROM
* - Init Creality DWIN encoder, show faux progress bar
* - Reset Status Message / Show Service Messages
* - Init MAX7219 LED Matrix
* - Init Direct Stepping (Klipper-style motion control)
* - Init TFT LVGL UI (with 3D Graphics)
* - Apply Password Lock - Hold for Authentication
* - Open Touch Screen Calibration screen, if not calibrated
* - Set Marlin to RUNNING State
*/ */
void setup() { void setup() {
#ifdef BOARD_PREINIT #ifdef BOARD_PREINIT
@ -1311,7 +1380,6 @@ void setup() {
#if PIN_EXISTS(STAT_LED_RED) #if PIN_EXISTS(STAT_LED_RED)
OUT_WRITE(STAT_LED_RED_PIN, LOW); // OFF OUT_WRITE(STAT_LED_RED_PIN, LOW); // OFF
#endif #endif
#if PIN_EXISTS(STAT_LED_BLUE) #if PIN_EXISTS(STAT_LED_BLUE)
OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // OFF OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // OFF
#endif #endif
@ -1364,19 +1432,13 @@ void setup() {
#endif #endif
#endif #endif
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
SETUP_RUN(mpe_settings_init());
#endif
#if ENABLED(PARKING_EXTRUDER) #if ENABLED(PARKING_EXTRUDER)
SETUP_RUN(pe_solenoid_init()); SETUP_RUN(pe_solenoid_init());
#endif #elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
SETUP_RUN(mpe_settings_init());
#if ENABLED(SWITCHING_TOOLHEAD) #elif ENABLED(SWITCHING_TOOLHEAD)
SETUP_RUN(swt_init()); SETUP_RUN(swt_init());
#endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
#if ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
SETUP_RUN(est_init()); SETUP_RUN(est_init());
#endif #endif

Loading…
Cancel
Save