Endstop invert flags as macros instead of const bool

Marlin/Conditionals.h

@@ -610,35 +610,33 @@
     #define _XMAX_ 101
     #define _YMAX_ 201
     #define _ZMAX_ 301
-    const bool Z2_MAX_ENDSTOP_INVERTING =
-      #if Z2_USE_ENDSTOP == _XMAX_
-        X_MAX_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN X_MAX_PIN
-        #undef USE_XMAX_PLUG
-      #elif Z2_USE_ENDSTOP == _YMAX_
-        Y_MAX_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN Y_MAX_PIN
-        #undef USE_YMAX_PLUG
-      #elif Z2_USE_ENDSTOP == _ZMAX_
-        Z_MAX_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN Z_MAX_PIN
-        #undef USE_ZMAX_PLUG
-      #elif Z2_USE_ENDSTOP == _XMIN_
-        X_MIN_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN X_MIN_PIN
-        #undef USE_XMIN_PLUG
-      #elif Z2_USE_ENDSTOP == _YMIN_
-        Y_MIN_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN Y_MIN_PIN
-        #undef USE_YMIN_PLUG
-      #elif Z2_USE_ENDSTOP == _ZMIN_
-        Z_MIN_ENDSTOP_INVERTING
-        #define Z2_MAX_PIN Z_MIN_PIN
-        #undef USE_ZMIN_PLUG
-      #else
-        0
-      #endif
-    ;
+    #if Z2_USE_ENDSTOP == _XMAX_
+      #define Z2_MAX_ENDSTOP_INVERTING X_MAX_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN X_MAX_PIN
+      #undef USE_XMAX_PLUG
+    #elif Z2_USE_ENDSTOP == _YMAX_
+      #define Z2_MAX_ENDSTOP_INVERTING Y_MAX_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN Y_MAX_PIN
+      #undef USE_YMAX_PLUG
+    #elif Z2_USE_ENDSTOP == _ZMAX_
+      #define Z2_MAX_ENDSTOP_INVERTING Z_MAX_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN Z_MAX_PIN
+      #undef USE_ZMAX_PLUG
+    #elif Z2_USE_ENDSTOP == _XMIN_
+      #define Z2_MAX_ENDSTOP_INVERTING X_MIN_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN X_MIN_PIN
+      #undef USE_XMIN_PLUG
+    #elif Z2_USE_ENDSTOP == _YMIN_
+      #define Z2_MAX_ENDSTOP_INVERTING Y_MIN_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN Y_MIN_PIN
+      #undef USE_YMIN_PLUG
+    #elif Z2_USE_ENDSTOP == _ZMIN_
+      #define Z2_MAX_ENDSTOP_INVERTING Z_MIN_ENDSTOP_INVERTING
+      #define Z2_MAX_PIN Z_MIN_PIN
+      #undef USE_ZMIN_PLUG
+    #else
+      #define Z2_MAX_ENDSTOP_INVERTING false
+    #endif
   #endif
 
   /**

Marlin/Configuration.h

@@ -437,13 +437,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Cartesio/Configuration.h

@@ -437,13 +437,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Felix/Configuration.h

@@ -419,13 +419,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -417,13 +417,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Hephestos/Configuration.h

@@ -429,13 +429,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -431,13 +431,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true;  // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true;  // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true;  // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true;  // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true;  // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/K8200/Configuration.h

@@ -454,13 +454,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/K8400/Configuration.h

@@ -414,13 +414,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/K8400/Dual-head/Configuration.h

@@ -414,13 +414,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -437,13 +437,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/RigidBot/Configuration.h

@@ -434,13 +434,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/SCARA/Configuration.h

@@ -445,13 +445,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/TAZ4/Configuration.h

@@ -458,13 +458,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/WITBOX/Configuration.h

@@ -429,13 +429,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -437,13 +437,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -479,13 +479,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/generic/Configuration.h

@@ -479,13 +479,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -479,13 +479,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -468,13 +468,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -477,13 +477,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/makibox/Configuration.h

@@ -440,13 +440,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -427,13 +427,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true  // set to true to invert the logic of the endstop.
 
 //===========================================================================
 //============================= Z Probe Options =============================