andrey
/
Marlin_FB4S
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

Add Chamber servo vent, auto fan (#19519)

vanilla_fb_2.0.x
ladismrkolj 4 years ago
committed by Scott Lahteine
parent
6fcbf11454
commit
2b845e5a75
6 changed files with 193 additions and 39 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 45
      Marlin/Configuration_adv.h
  2. 17
      Marlin/src/inc/Conditionals_LCD.h
  3. 45
      Marlin/src/inc/Conditionals_adv.h
  4. 32
      Marlin/src/inc/SanityCheck.h
  5. 80
      Marlin/src/module/temperature.cpp
  6. 1
      Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h

45
Marlin/Configuration_adv.h
View File

@ -32,11 +32,10 @@
*/
#define CONFIGURATION_ADV_H_VERSION 020007
// @section temperature
//===========================================================================
//============================= Thermal Settings ============================
//===========================================================================
// @section temperature
/**
* Thermocouple sensors are quite sensitive to noise. Any noise induced in
@ -125,9 +124,19 @@
#define HEATER_BED_INVERTING true
#endif
/**
* Heated Chamber settings
*/
//
// Heated Bed Bang-Bang options
//
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
#define BED_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > BED_HYSTERESIS
#endif
#endif
//
// Heated Chamber options
//
#if TEMP_SENSOR_CHAMBER
#define CHAMBER_MINTEMP 5
#define CHAMBER_MAXTEMP 60
@ -135,12 +144,28 @@
//#define CHAMBER_LIMIT_SWITCHING
//#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
//#define HEATER_CHAMBER_INVERTING false
#endif
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
#define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
//#define CHAMBER_FAN // Enable a fan on the chamber
#if ENABLED(CHAMBER_FAN)
#define CHAMBER_FAN_MODE 2 // Fan control mode: 0=Static; 1=Linear increase when temp is higher than target; 2=V-shaped curve.
#if CHAMBER_FAN_MODE == 0
#define CHAMBER_FAN_BASE 255 // Chamber fan PWM (0-255)
#elif CHAMBER_FAN_MODE == 1
#define CHAMBER_FAN_BASE 128 // Base chamber fan PWM (0-255); turns on when chamber temperature is above the target
#define CHAMBER_FAN_FACTOR 25 // PWM increase per °C above target
#elif CHAMBER_FAN_MODE == 2
#define CHAMBER_FAN_BASE 128 // Minimum chamber fan PWM (0-255)
#define CHAMBER_FAN_FACTOR 25 // PWM increase per °C difference from target
#endif
#endif
//#define CHAMBER_VENT // Enable a servo-controlled vent on the chamber
#if ENABLED(CHAMBER_VENT)
#define CHAMBER_VENT_SERVO_NR 1 // Index of the vent servo
#define HIGH_EXCESS_HEAT_LIMIT 5 // How much above target temp to consider there is excess heat in the chamber
#define LOW_EXCESS_HEAT_LIMIT 3
#define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
#define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
#endif
#endif

17
Marlin/src/inc/Conditionals_LCD.h
View File

@ -603,10 +603,6 @@
#define DO_SWITCH_EXTRUDER 1
#endif
#ifdef SWITCHING_NOZZLE_E1_SERVO_NR
#define SWITCHING_NOZZLE_TWO_SERVOS 1
#endif
/**
* Default hotend offsets, if not defined
*/
@ -657,14 +653,7 @@
#ifndef Z_PROBE_SERVO_NR
#define Z_PROBE_SERVO_NR 0
#endif
#ifndef NUM_SERVOS
#define NUM_SERVOS (Z_PROBE_SERVO_NR + 1)
#endif
#undef DEACTIVATE_SERVOS_AFTER_MOVE
#if NUM_SERVOS == 1
#undef SERVO_DELAY
#define SERVO_DELAY { 50 }
#endif
// Always disable probe pin inverting for BLTouch
#undef Z_MIN_PROBE_ENDSTOP_INVERTING
@ -675,14 +664,10 @@
#endif
#endif
#ifndef NUM_SERVOS
#define NUM_SERVOS 0
#endif
/**
* Set a flag for a servo probe (or BLTouch)
*/
#if defined(Z_PROBE_SERVO_NR) && Z_PROBE_SERVO_NR >= 0
#ifdef Z_PROBE_SERVO_NR
#define HAS_Z_SERVO_PROBE 1
#endif
#if ANY(HAS_Z_SERVO_PROBE, SWITCHING_EXTRUDER, SWITCHING_NOZZLE)

45
Marlin/src/inc/Conditionals_adv.h
View File

@ -26,6 +26,51 @@
* Defines that depend on advanced configuration.
*/
#ifdef SWITCHING_NOZZLE_E1_SERVO_NR
#define SWITCHING_NOZZLE_TWO_SERVOS 1
#endif
// Determine NUM_SERVOS if none was supplied
#ifndef NUM_SERVOS
#define NUM_SERVOS 0
#if ANY(CHAMBER_VENT, HAS_Z_SERVO_PROBE, SWITCHING_EXTRUDER, SWITCHING_NOZZLE)
#if NUM_SERVOS <= Z_PROBE_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (Z_PROBE_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= CHAMBER_VENT_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (CHAMBER_VENT_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= SWITCHING_TOOLHEAD_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (SWITCHING_TOOLHEAD_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= SWITCHING_NOZZLE_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (SWITCHING_NOZZLE_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= SWITCHING_NOZZLE_E1_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (SWITCHING_NOZZLE_E1_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= SWITCHING_EXTRUDER_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (SWITCHING_EXTRUDER_SERVO_NR + 1)
#endif
#if NUM_SERVOS <= SWITCHING_EXTRUDER_E23_SERVO_NR
#undef NUM_SERVOS
#define NUM_SERVOS (SWITCHING_EXTRUDER_E23_SERVO_NR + 1)
#endif
#endif
#endif
// Convenience override for a BLTouch alone
#if ENABLED(BLTOUCH) && NUM_SERVOS == 1
#undef SERVO_DELAY
#define SERVO_DELAY { 50 }
#endif
#if EXTRUDERS == 0
#define NO_VOLUMETRICS
#undef TEMP_SENSOR_0

32
Marlin/src/inc/SanityCheck.h
View File

@ -1249,8 +1249,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
* NUM_SERVOS is required for a Z servo probe
*/
#if HAS_Z_SERVO_PROBE
#ifndef NUM_SERVOS
#error "You must set NUM_SERVOS for a Z servo probe (Z_PROBE_SERVO_NR)."
#if !NUM_SERVOS
#error "NUM_SERVOS is required for a Z servo probe (Z_PROBE_SERVO_NR)."
#elif Z_PROBE_SERVO_NR >= NUM_SERVOS
#error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS."
#elif Z_PROBE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your servo or BLTOUCH probe."
#elif Z_PROBE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
@ -1259,8 +1261,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "SERVO2_PIN must be defined for your servo or BLTOUCH probe."
#elif Z_PROBE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your servo or BLTOUCH probe."
#elif Z_PROBE_SERVO_NR >= NUM_SERVOS
#error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS."
#endif
#endif
@ -1807,6 +1807,30 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
#error "TEMP_SENSOR_CHAMBER requires TEMP_CHAMBER_PIN. Please add it to your configuration."
#endif
#if ENABLED(CHAMBER_FAN) && !(defined(CHAMBER_FAN_MODE) && WITHIN(CHAMBER_FAN_MODE, 0, 2))
#error "CHAMBER_FAN_MODE must be between 0 and 2. Please update your Configuration_adv.h."
#endif
#if ENABLED(CHAMBER_VENT)
#ifndef CHAMBER_VENT_SERVO_NR
#error "CHAMBER_VENT_SERVO_NR is required for CHAMBER SERVO. Update your Configuration_adv.h."
#elif !NUM_SERVOS
#error "NUM_SERVOS is required for a Heated Chamber vent servo (CHAMBER_VENT_SERVO_NR)."
#elif CHAMBER_VENT_SERVO_NR >= NUM_SERVOS
#error "CHAMBER_VENT_SERVO_NR must be smaller than NUM_SERVOS."
#elif HAS_Z_SERVO_PROBE && CHAMBER_VENT_SERVO_NR == Z_PROBE_SERVO_NR
#error "CHAMBER SERVO is already used by BLTOUCH. Please change."
#elif CHAMBER_VENT_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your Heated Chamber vent servo."
#elif CHAMBER_VENT_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
#error "SERVO1_PIN must be defined for your Heated Chamber vent servo."
#elif CHAMBER_VENT_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
#error "SERVO2_PIN must be defined for your Heated Chamber vent servo."
#elif CHAMBER_VENT_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your Heated Chamber vent servo."
#endif
#endif
#if TEMP_SENSOR_PROBE
#if !PIN_EXISTS(TEMP_PROBE)
#error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN. Please add it to your configuration."

80
Marlin/src/module/temperature.cpp
View File

@ -111,6 +111,9 @@
#include "../libs/buzzer.h"
#endif
#if HAS_SERVOS
#include "./servo.h"
#endif
#if HOTEND_USES_THERMISTOR
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
static const temp_entry_t* heater_ttbl_map[2] = { HEATER_0_TEMPTABLE, HEATER_1_TEMPTABLE };
@ -271,6 +274,11 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
#if HAS_TEMP_CHAMBER
chamber_info_t Temperature::temp_chamber; // = { 0 }
#if HAS_HEATED_CHAMBER
int16_t fan_chamber_pwm;
bool flag_chamber_off;
bool flag_chamber_excess_heat = false;
millis_t next_cool_check_ms_2 = 0;
float old_temp = 9999;
#ifdef CHAMBER_MINTEMP
int16_t Temperature::mintemp_raw_CHAMBER = HEATER_CHAMBER_RAW_LO_TEMP;
#endif
@ -1194,18 +1202,84 @@ void Temperature::manage_heater() {
}
#endif
#if EITHER(CHAMBER_FAN, CHAMBER_VENT)
if (temp_chamber.target > CHAMBER_MINTEMP) {
flag_chamber_off = false;
#if ENABLED(CHAMBER_FAN)
#if CHAMBER_FAN_MODE == 0
fan_chamber_pwm = CHAMBER_FAN_BASE
#elif CHAMBER_FAN_MODE == 1
fan_chamber_pwm = temp_chamber.celsius > temp_chamber.target ? CHAMBER_FAN_BASE + ((temp_chamber.celsius - temp_chamber.target) * CHAMBER_FAN_FACTOR ) : 0;
#elif CHAMBER_FAN_MODE == 2
fan_chamber_pwm = (CHAMBER_FAN_BASE) + (CHAMBER_FAN_FACTOR) * ABS(temp_chamber.celsius - temp_chamber.target);
if (temp_chamber.soft_pwm_amount)
fan_chamber_pwm += (CHAMBER_FAN_FACTOR) * 2;
#endif
fan_chamber_pwm = _MIN(225, fan_chamber_pwm);
thermalManager.set_fan_speed(2, fan_chamber_pwm); // TODO: instead of fan 2, set to chamber fan
#endif
#if ENABLED(CHAMBER_VENT)
#ifndef MIN_COOLING_SLOPE_TIME_CHAMBER_VENT
#define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
#endif
#ifndef MIN_COOLING_SLOPE_DEG_CHAMBER_VENT
#define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
#endif
if( (temp_chamber.celsius - temp_chamber.target >= HIGH_EXCESS_HEAT_LIMIT) && !flag_chamber_excess_heat) {
// open vent after MIN_COOLING_SLOPE_TIME_CHAMBER_VENT seconds
// if the temperature did not drop at least MIN_COOLING_SLOPE_DEG_CHAMBER_VENT
if (next_cool_check_ms_2 == 0 || ELAPSED(ms, next_cool_check_ms_2)) {
if (old_temp - temp_chamber.celsius < float(MIN_COOLING_SLOPE_DEG_CHAMBER_VENT)) flag_chamber_excess_heat = true; //the bed is heating the chamber too much
next_cool_check_ms_2 = ms + 1000UL * MIN_COOLING_SLOPE_TIME_CHAMBER_VENT;
old_temp = temp_chamber.celsius;
}
}
else {
next_cool_check_ms_2 = 0;
old_temp = 9999;
}
if (flag_chamber_excess_heat && (temp_chamber.celsius - temp_chamber.target <= -LOW_EXCESS_HEAT_LIMIT) ) {
flag_chamber_excess_heat = false;
}
#endif
}
else if (!flag_chamber_off) {
#if ENABLED(CHAMBER_FAN)
flag_chamber_off = true;
thermalManager.set_fan_speed(2, 0);
#endif
#if ENABLED(CHAMBER_VENT)
flag_chamber_excess_heat = false;
MOVE_SERVO(CHAMBER_VENT_SERVO_NR, 90);
#endif
}
#endif
if (ELAPSED(ms, next_chamber_check_ms)) {
next_chamber_check_ms = ms + CHAMBER_CHECK_INTERVAL;
if (WITHIN(temp_chamber.celsius, CHAMBER_MINTEMP, CHAMBER_MAXTEMP)) {
if (!flag_chamber_excess_heat){
#if ENABLED(CHAMBER_LIMIT_SWITCHING)
if (temp_chamber.celsius >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
temp_chamber.soft_pwm_amount = 0;
else if (temp_chamber.celsius <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
temp_chamber.soft_pwm_amount = MAX_CHAMBER_POWER >> 1;
temp_chamber.soft_pwm_amount = (MAX_CHAMBER_POWER) >> 1;
#else
temp_chamber.soft_pwm_amount = temp_chamber.celsius < temp_chamber.target ? MAX_CHAMBER_POWER >> 1 : 0;
temp_chamber.soft_pwm_amount = temp_chamber.celsius < temp_chamber.target ? (MAX_CHAMBER_POWER) >> 1 : 0;
#endif
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, 0);
#endif
}
else {
temp_chamber.soft_pwm_amount = 0;
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, temp_chamber.celsius <= temp_chamber.target ? 0 : 90);
#endif
}
}
else {
temp_chamber.soft_pwm_amount = 0;
@ -3370,7 +3444,7 @@ void Temperature::tick() {
#define MIN_COOLING_SLOPE_DEG_CHAMBER 1.50
#endif
#ifndef MIN_COOLING_SLOPE_TIME_CHAMBER
#define MIN_COOLING_SLOPE_TIME_CHAMBER 60
#define MIN_COOLING_SLOPE_TIME_CHAMBER 120
#endif
bool Temperature::wait_for_chamber(const bool no_wait_for_cooling/*=true*/) {

1
Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h
View File

@ -41,6 +41,7 @@
// Servos
//
#define SERVO0_PIN PA1
#define SERVO1_PIN PC9
//
// Trinamic Stallguard pins

Write Preview
Loading…
Cancel
Save