|
|
@ -69,48 +69,48 @@ |
|
|
|
#if MB(RAMPS_13_EEB) && ENABLED(FILAMENT_SENSOR) // FMM added for Filament Extruder
|
|
|
|
// define analog pin for the filament width sensor input
|
|
|
|
// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
|
|
|
|
#define FILWIDTH_PIN 5 |
|
|
|
#define FILWIDTH_PIN 5 |
|
|
|
#endif |
|
|
|
|
|
|
|
#if ENABLED(Z_PROBE_ENDSTOP) |
|
|
|
// Define a pin to use as the signal pin on Arduino for the Z_PROBE endstop.
|
|
|
|
#define Z_PROBE_PIN 32 |
|
|
|
#define Z_PROBE_PIN 32 |
|
|
|
#endif |
|
|
|
|
|
|
|
#if ENABLED(FILAMENT_RUNOUT_SENSOR) |
|
|
|
// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
|
|
|
|
#define FILRUNOUT_PIN 4 |
|
|
|
#define FILRUNOUT_PIN 4 |
|
|
|
#endif |
|
|
|
|
|
|
|
#if MB(RAMPS_13_EFF) || ENABLED(IS_RAMPS_EFB) |
|
|
|
#define FAN_PIN 9 // (Sprinter config)
|
|
|
|
#define FAN_PIN 9 // (Sprinter config)
|
|
|
|
#if MB(RAMPS_13_EFF) |
|
|
|
#define CONTROLLERFAN_PIN -1 // Pin used for the fan to cool controller
|
|
|
|
#endif |
|
|
|
#elif MB(RAMPS_13_EEF) || MB(RAMPS_13_SF) |
|
|
|
#define FAN_PIN 8 |
|
|
|
#define FAN_PIN 8 |
|
|
|
#else |
|
|
|
#define FAN_PIN 4 // IO pin. Buffer needed
|
|
|
|
#define FAN_PIN 4 // IO pin. Buffer needed
|
|
|
|
#endif |
|
|
|
|
|
|
|
#define PS_ON_PIN 12 |
|
|
|
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) || ENABLED(G3D_PANEL) |
|
|
|
#define KILL_PIN 41 |
|
|
|
#define KILL_PIN 41 |
|
|
|
#else |
|
|
|
#define KILL_PIN -1 |
|
|
|
#define KILL_PIN -1 |
|
|
|
#endif |
|
|
|
|
|
|
|
#if MB(RAMPS_13_EFF) |
|
|
|
#define HEATER_0_PIN 8 |
|
|
|
#define HEATER_0_PIN 8 |
|
|
|
#else |
|
|
|
#define HEATER_0_PIN 10 // EXTRUDER 1
|
|
|
|
#define HEATER_0_PIN 10 // EXTRUDER 1
|
|
|
|
#endif |
|
|
|
|
|
|
|
#if MB(RAMPS_13_SF) || ENABLED(IS_RAMPS_EFB) |
|
|
|
#define HEATER_1_PIN -1 |
|
|
|
#define HEATER_1_PIN -1 |
|
|
|
#else |
|
|
|
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
|
|
|
|
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
|
|
|
|
#endif |
|
|
|
|
|
|
|
#define HEATER_2_PIN -1 |
|
|
@ -120,9 +120,9 @@ |
|
|
|
#define TEMP_2_PIN -1 // ANALOG NUMBERING
|
|
|
|
|
|
|
|
#if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF) |
|
|
|
#define HEATER_BED_PIN -1 // NO BED
|
|
|
|
#define HEATER_BED_PIN -1 // NO BED
|
|
|
|
#else |
|
|
|
#define HEATER_BED_PIN 8 // BED
|
|
|
|
#define HEATER_BED_PIN 8 // BED
|
|
|
|
#endif |
|
|
|
|
|
|
|
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
|
|
|
|