Browse Source

BTT SKR 1.3 pins for Anet Full Graphics LCD (#16047)

pull/1/head
hammerhead2k2 5 years ago
committed by Scott Lahteine
parent
commit
19f840a9b5
  1. 61
      Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h

61
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h

@ -169,32 +169,69 @@
#endif
/**
* _____ _____
* NC | · · | GND 5V | · · | GND
* RESET | · · | 1.31(SD_DETECT) (LCD_D7) 1.23 | · · | 1.22 (LCD_D6)
* (MOSI)0.18 | · · | 3.25(BTN_EN2) (LCD_D5) 1.21 | · · | 1.20 (LCD_D4)
* (SD_SS)0.16 | · · | 3.26(BTN_EN1) (LCD_RS) 1.19 | · · | 1.18 (LCD_EN)
* (SCK)0.15 | · · | 0.17(MISO) (BTN_ENC) 0.28 | · · | 1.30 (BEEPER)
* ----- -----
* EXP2 EXP1
* _____ _____
* NC | · · | GND 5V | · · | GND
* RESET | · · | 1.31 (SD_DETECT) (LCD_D7) 1.23 | · · | 1.22 (LCD_D6)
* (MOSI) 0.18 | · · | 3.25 (BTN_EN2) (LCD_D5) 1.21 | · · | 1.20 (LCD_D4)
* (SD_SS) 0.16 | · · | 3.26 (BTN_EN1) (LCD_RS) 1.19 | · · | 1.18 (LCD_EN)
* (SCK) 0.15 | · · | 0.17 (MISO) (BTN_ENC) 0.28 | · · | 1.30 (BEEPER)
* ----- -----
* EXP2 EXP1
*/
#if HAS_SPI_LCD
#define BTN_ENC P0_28 // (58) open-drain
#if ENABLED(CR10_STOCKDISPLAY)
#if ENABLED(ANET_FULL_GRAPHICS_LCD)
#error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue."
/**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.)
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
*
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
*
* The ANET_FULL_GRAPHICS_LCD connector plug:
*
* BEFORE AFTER
* _____ _____
* GND 1 | · · | 2 5V 5V 1 | · · | 2 GND
* CS 3 | · · | 4 BTN_EN2 CS 3 | · · | 4 BTN_EN2
* SID 5 | · · | 6 BTN_EN1 SID 5 | · · | 6 BTN_EN1
* open 7 | · · | 8 BTN_ENC CLK 7 | · · | 8 BTN_ENC
* CLK 9 | · · | 10 Beeper open 9 | · · | 10 Beeper
* ----- -----
* LCD LCD
*/
#define LCD_PINS_RS P1_23
#define BTN_EN1 P1_20
#define BTN_EN2 P1_22
#define BTN_ENC P1_18
#define LCD_PINS_ENABLE P1_21
#define LCD_PINS_D4 P1_19
#elif ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS P1_22
#define BTN_EN1 P1_18
#define BTN_EN2 P1_20
#define BTN_ENC P0_28 // (58) open-drain
#define LCD_PINS_ENABLE P1_23
#define LCD_PINS_D4 P1_21
#else
#else // !CR10_STOCKDISPLAY
#define LCD_PINS_RS P1_19
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P0_28 // (58) open-drain
#define LCD_PINS_ENABLE P1_18
#define LCD_PINS_D4 P1_20
@ -247,7 +284,7 @@
#endif // !FYSETC_MINI_12864
#endif
#endif // !CR10_STOCKDISPLAY
#endif // HAS_SPI_LCD

Loading…
Cancel
Save