🎨 Apply more HAS_DELTA_SENSORLESS_PROBING

Marlin/src/gcode/calibrate/G33.cpp

@@ -425,7 +425,7 @@ void GcodeSuite::G33() {
 
   const bool stow_after_each = parser.seen_test('E');
 
-  #if ENABLED(SENSORLESS_PROBING)
+  #if HAS_DELTA_SENSORLESS_PROBING
     probe.test_sensitivity.x = !parser.seen_test('X');
     TERN_(HAS_Y_AXIS, probe.test_sensitivity.y = !parser.seen_test('Y'));
     TERN_(HAS_Z_AXIS, probe.test_sensitivity.z = !parser.seen_test('Z'));

Marlin/src/module/delta.cpp

@@ -254,7 +254,7 @@ void home_delta() {
   current_position.z = DIFF_TERN(HAS_BED_PROBE, delta_height + 10, probe.offset.z);
   line_to_current_position(homing_feedrate(Z_AXIS));
   planner.synchronize();
-  TERN_(SENSORLESS_PROBING,endstops.report_states());
+  TERN_(HAS_DELTA_SENSORLESS_PROBING, endstops.report_states());
 
   // Re-enable stealthChop if used. Disable diag1 pin on driver.
   #if ENABLED(SENSORLESS_HOMING) && DISABLED(ENDSTOPS_ALWAYS_ON_DEFAULT)

Marlin/src/module/endstops.cpp

@@ -595,7 +595,7 @@ void _O2 Endstops::report_states() {
 // The following routines are called from an ISR context. It could be the temperature ISR, the
 // endstop ISR or the Stepper ISR.
 
-#if BOTH(DELTA, SENSORLESS_PROBING)
+#if HAS_DELTA_SENSORLESS_PROBING
   #define __ENDSTOP(AXIS, ...) AXIS ##_MAX
   #define _ENDSTOP_PIN(AXIS, ...) AXIS ##_MAX_PIN
   #define _ENDSTOP_INVERTING(AXIS, ...) AXIS ##_MAX_ENDSTOP_INVERTING

Marlin/src/module/probe.cpp

@@ -493,7 +493,7 @@ bool Probe::probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s) {
   // Disable stealthChop if used. Enable diag1 pin on driver.
   #if ENABLED(SENSORLESS_PROBING)
     sensorless_t stealth_states { false };
-    #if ENABLED(DELTA)
+    #if HAS_DELTA_SENSORLESS_PROBING
       if (probe.test_sensitivity.x) stealth_states.x = tmc_enable_stallguard(stepperX);  // Delta watches all DIAG pins for a stall
       if (probe.test_sensitivity.y) stealth_states.y = tmc_enable_stallguard(stepperY);
     #endif
@@ -509,7 +509,7 @@ bool Probe::probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s) {
 
   // Check to see if the probe was triggered
   const bool probe_triggered =
-    #if BOTH(DELTA, SENSORLESS_PROBING)
+    #if HAS_DELTA_SENSORLESS_PROBING
       endstops.trigger_state() & (_BV(X_MAX) | _BV(Y_MAX) | _BV(Z_MAX))
     #else
       TEST(endstops.trigger_state(), Z_MIN_PROBE)
@@ -521,7 +521,7 @@ bool Probe::probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s) {
   // Re-enable stealthChop if used. Disable diag1 pin on driver.
   #if ENABLED(SENSORLESS_PROBING)
     endstops.not_homing();
-    #if ENABLED(DELTA)
+    #if HAS_DELTA_SENSORLESS_PROBING
       if (probe.test_sensitivity.x) tmc_disable_stallguard(stepperX, stealth_states.x);
       if (probe.test_sensitivity.y) tmc_disable_stallguard(stepperY, stealth_states.y);
     #endif
@@ -765,7 +765,7 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai
   #endif
 
   // On delta keep Z below clip height or do_blocking_move_to will abort
-  xyz_pos_t npos = { rx, ry, _MIN(TERN(DELTA, delta_clip_start_height, current_position.z), current_position.z) };
+  xyz_pos_t npos = { rx, ry, TERN(DELTA, _MIN(delta_clip_start_height, current_position.z), current_position.z) };
   if (probe_relative) {                                     // The given position is in terms of the probe
     if (!can_reach(npos)) {
       if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("Position Not Reachable");
@@ -827,7 +827,7 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai
    */
   void Probe::enable_stallguard_diag1() {
     #if ENABLED(SENSORLESS_PROBING)
-      #if ENABLED(DELTA)
+      #if HAS_DELTA_SENSORLESS_PROBING
         stealth_states.x = tmc_enable_stallguard(stepperX);
         stealth_states.y = tmc_enable_stallguard(stepperY);
       #endif
@@ -842,7 +842,7 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai
   void Probe::disable_stallguard_diag1() {
     #if ENABLED(SENSORLESS_PROBING)
       endstops.not_homing();
-      #if ENABLED(DELTA)
+      #if HAS_DELTA_SENSORLESS_PROBING
         tmc_disable_stallguard(stepperX, stealth_states.x);
         tmc_disable_stallguard(stepperY, stealth_states.y);
       #endif
@@ -907,6 +907,6 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai
     #endif
   }
 
-#endif // SENSORLESS_PROBING
+#endif // SENSORLESS_PROBING || SENSORLESS_HOMING
 
 #endif // HAS_BED_PROBE