Merge pull request #7919 from thinkyhead/bf2_neopixel_full

[2.0.x] Different NEOPIXEL types

Marlin/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/Marlin.cpp

@@ -796,7 +796,7 @@ void setup() {
     OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // turn it off
   #endif
 
-  #if ENABLED(NEOPIXEL_RGBW_LED)
+  #if ENABLED(NEOPIXEL_LED)
     SET_OUTPUT(NEOPIXEL_PIN);
     setup_neopixel();
   #endif

Marlin/src/config/default/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -1608,14 +1608,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1626,10 +1632,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1644,7 +1653,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -1747,14 +1747,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1765,10 +1771,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1783,7 +1792,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -1596,14 +1596,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1614,10 +1620,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1632,7 +1641,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -1579,14 +1579,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1597,10 +1603,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1615,7 +1624,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -1589,14 +1589,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1607,10 +1613,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1625,7 +1634,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -1579,14 +1579,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1597,10 +1603,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1615,7 +1624,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -1587,14 +1587,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1605,10 +1611,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1623,7 +1632,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -1598,14 +1598,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1616,10 +1622,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1634,7 +1643,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Felix/Configuration.h

@@ -1570,14 +1570,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1588,10 +1594,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1606,7 +1615,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -1570,14 +1570,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1588,10 +1594,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1606,7 +1615,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Folger Tech/i3-2020/Configuration.h

@@ -1593,14 +1593,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1611,10 +1617,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1629,7 +1638,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -1603,14 +1603,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1621,10 +1627,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1639,7 +1648,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -1592,14 +1592,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1610,10 +1616,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1628,7 +1637,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -1616,14 +1616,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1634,10 +1640,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1652,7 +1661,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/SCARA/Configuration.h

@@ -1600,14 +1600,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1618,10 +1624,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1636,7 +1645,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -1619,28 +1619,37 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
-#define RGB_LED
+
+//#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
-  #define RGB_LED_R_PIN 11
-  #define RGB_LED_G_PIN 10
-  #define RGB_LED_B_PIN 17
+  #define RGB_LED_R_PIN 34
+  #define RGB_LED_G_PIN 43
+  #define RGB_LED_B_PIN 35
   #define RGB_LED_W_PIN -1
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1655,7 +1664,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -1644,14 +1644,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1662,10 +1668,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1680,7 +1689,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -1623,14 +1623,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1641,10 +1647,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1659,7 +1668,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -1588,14 +1588,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1606,10 +1612,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1624,7 +1633,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1716,14 +1716,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1734,10 +1740,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1752,7 +1761,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1709,14 +1709,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1727,10 +1733,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1745,7 +1754,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -1704,14 +1704,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1722,10 +1728,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1740,7 +1749,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -1707,14 +1707,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1725,10 +1731,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1743,7 +1752,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -1707,14 +1707,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1725,10 +1731,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1743,7 +1752,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -1716,14 +1716,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1734,10 +1740,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1752,7 +1761,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -1602,14 +1602,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1620,10 +1626,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1638,7 +1647,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/makibox/Configuration.h

@@ -1591,14 +1591,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1609,10 +1615,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1627,7 +1636,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/stm32f103ret6/Configuration.h

@@ -1561,10 +1561,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1579,7 +1582,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -1583,14 +1583,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1601,10 +1607,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1619,7 +1628,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/config/examples/wt150/Configuration.h

@@ -1593,14 +1593,20 @@
  * Adds the M150 command to set the LED (or LED strip) color.
  * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
  * luminance values can be set from 0 to 255.
+ * For Neopixel LED overall brightness parameters is also available
  *
  * *** CAUTION ***
  *  LED Strips require a MOFSET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *  Neopixel LED is 5V powered, but linear 5V regulator on Arduino
+ *  cannot handle the current, separate 5V power supply must be used
  * *** CAUTION ***
  *
+ * LED type. This options are mutualy exclusive. Uncomment only one.
+ *
  */
+
 //#define RGB_LED
 //#define RGBW_LED
 #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@@ -1611,10 +1617,13 @@
 #endif
 
 // Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_RGBW_LED
-#if ENABLED(NEOPIXEL_RGBW_LED)
-  #define NEOPIXEL_PIN    4       // D4 (EXP2-5 on Printrboard)
-  #define NEOPIXEL_PIXELS 3
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRB  // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs on strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
+  #define NEOPIXEL_BRIGHTNESS 255  // Initial brightness 0-255
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 #endif
 
@@ -1629,7 +1638,7 @@
  *  - Change to green once print has finished
  *  - Turn off after the print has finished and the user has pushed a button
  */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
   #define PRINTER_EVENT_LEDS
 #endif
 

Marlin/src/feature/leds/leds.cpp

@@ -31,17 +31,14 @@
 #include "leds.h"
 
 void set_led_color(
-  const uint8_t r, const uint8_t g, const uint8_t b
-  #if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
-    , const uint8_t w
-    #if ENABLED(NEOPIXEL_RGBW_LED)
-      , bool isSequence
-    #endif
-  #endif
+  const uint8_t r, const uint8_t g, const uint8_t b , const uint8_t w , const uint8_t p
 ) {
 
-  #if ENABLED(NEOPIXEL_RGBW_LED)
-    if (neopixel_set_led_color(r, g, b, w, isSequence))
+  #if ENABLED(NEOPIXEL_LED)
+    if (w == 255 || (r == 255 && g == 255 && b == 255))
+      neopixel_set_led_color(NEO_WHITE, p);
+    else
+      neopixel_set_led_color(r, g, b, w, p);
     return;
   #endif
 

Marlin/src/feature/leds/leds.h

@@ -27,7 +27,7 @@
 #ifndef __LEDS_H__
 #define __LEDS_H__
 
-#if ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(NEOPIXEL_LED)
   #include <Adafruit_NeoPixel.h>
   #include "neopixel.h"
 #endif
@@ -40,14 +40,28 @@
   #include "pca9632.h"
 #endif
 
-void set_led_color(
-  const uint8_t r, const uint8_t g, const uint8_t b
-  #if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
-    , const uint8_t w = 0
-    #if ENABLED(NEOPIXEL_RGBW_LED)
-      , bool isSequence = false
-    #endif
+#if ENABLED(NEOPIXEL_LED) 
+  #if NEOPIXEL_TYPE == NEO_RGB || NEOPIXEL_TYPE == NEO_RBG || NEOPIXEL_TYPE == NEO_GRB || NEOPIXEL_TYPE == NEO_GBR || NEOPIXEL_TYPE == NEO_BRG || NEOPIXEL_TYPE == NEO_BGR
+    #define NEO_WHITE 255, 255, 255
+  #else
+    #define NEO_WHITE 0, 0, 0, 255
   #endif
+#endif
+
+#if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632)
+  #define LED_WHITE 255, 255, 255
+#elif ENABLED(RGBW_LED)
+  #define LED_WHITE 0, 0, 0, 255
+#endif
+
+#if ENABLED(NEOPIXEL_LED)
+  #define LED_BRIGHTNESS pixels.getBrightness()
+#else
+  #define LED_BRIGHTNESS 255
+#endif
+
+void set_led_color(
+  const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w = 0, const uint8_t p = 255
 );
 
 #endif // __LEDS_H__

Marlin/src/feature/leds/neopixel.cpp

@@ -26,11 +26,11 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if ENABLED(NEOPIXEL_RGBW_LED)
+#if ENABLED(NEOPIXEL_LED)
 
 #include "neopixel.h"
 
-Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEO_GRBW + NEO_KHZ800);
+Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEOPIXEL_TYPE + NEO_KHZ800);
 
 void set_neopixel_color(const uint32_t color) {
   for (uint16_t i = 0; i < pixels.numPixels(); ++i)
@@ -39,7 +39,7 @@ void set_neopixel_color(const uint32_t color) {
 }
 
 void setup_neopixel() {
-  pixels.setBrightness(255); // 0 - 255 range
+  pixels.setBrightness(NEOPIXEL_BRIGHTNESS); // 0 - 255 range
   pixels.begin();
   pixels.show(); // initialize to all off
 
@@ -55,18 +55,19 @@ void setup_neopixel() {
   set_neopixel_color(pixels.Color(0, 0, 0, 255));    // white
 }
 
-bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const bool isSequence) {
+bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p) {
   const uint32_t color = pixels.Color(r, g, b, w);
-  static uint16_t nextLed = 0;
-  if (!isSequence)
+  pixels.setBrightness(p);
+  #if !ENABLED(NEOPIXEL_IS_SEQUENTIAL)
     set_neopixel_color(color);
-  else {
+    return false;
+  #else
+    static uint16_t nextLed = 0;
     pixels.setPixelColor(nextLed, color);
     pixels.show();
     if (++nextLed >= pixels.numPixels()) nextLed = 0;
     return true;
-  }
-  return false;
+  #endif
 }
 
-#endif // NEOPIXEL_RGBW_LED
+#endif // NEOPIXEL_LED

Marlin/src/feature/leds/neopixel.h

@@ -31,7 +31,7 @@
 #include <stdint.h>
 
 void setup_neopixel();
-bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const bool isSequence);
+bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p);
 
 extern Adafruit_NeoPixel pixels;
 

Marlin/src/gcode/feature/leds/M150.cpp

@@ -28,27 +28,30 @@
 #include "../../../feature/leds/leds.h"
 
 /**
- * M150: Set Status LED Color - Use R-U-B-W for R-G-B-W
- *
- * Always sets all 3 or 4 components. If a component is left out, set to 0.
- *
- * Examples:
- *
- *   M150 R255       ; Turn LED red
- *   M150 R255 U127  ; Turn LED orange (PWM only)
- *   M150            ; Turn LED off
- *   M150 R U B      ; Turn LED white
- *   M150 W          ; Turn LED white using a white LED
- *
- */
+* M150: Set Status LED Color - Use R-U-B-W for R-G-B-W
+*       and Brightness       - Use P (for NEOPIXEL only)
+*
+* Always sets all 3 or 4 components. If a component is left out, set to 0.
+*                                    If brightness is left out, no value changed
+*
+* Examples:
+*
+*   M150 R255       ; Turn LED red
+*   M150 R255 U127  ; Turn LED orange (PWM only)
+*   M150            ; Turn LED off
+*   M150 R U B      ; Turn LED white
+*   M150 W          ; Turn LED white using a white LED
+*   M150 P127       ; Set LED 50% brightness
+*   M150 P          ; Set LED full brightness
+*/
+
 void GcodeSuite::M150() {
   set_led_color(
     parser.seen('R') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
     parser.seen('U') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
-    parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0
-    #if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
-      , parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0
-    #endif
+    parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
+    parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
+    parser.seen('P') ? (parser.has_value() ? parser.value_byte() : 255) : LED_BRIGHTNESS
   );
 }
 

Marlin/src/gcode/gcode.h

@@ -138,7 +138,7 @@
  * M140 - Set bed target temp. S<temp>
  * M145 - Set heatup values for materials on the LCD. H<hotend> B<bed> F<fan speed> for S<material> (0=PLA, 1=ABS)
  * M149 - Set temperature units. (Requires TEMPERATURE_UNITS_SUPPORT)
- * M150 - Set Status LED Color as R<red> U<green> B<blue>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, or PCA9632)
+ * M150 - Set Status LED Color as R<red> U<green> B<blue> P<bright>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, NEOPIXEL_LED, or PCA9632).
  * M155 - Auto-report temperatures with interval of S<seconds>. (Requires AUTO_REPORT_TEMPERATURES)
  * M163 - Set a single proportion for a mixing extruder. (Requires MIXING_EXTRUDER)
  * M164 - Save the mix as a virtual extruder. (Requires MIXING_EXTRUDER and MIXING_VIRTUAL_TOOLS)

Marlin/src/gcode/temperature/M104_M109.cpp

@@ -31,7 +31,7 @@
   #include "../../module/printcounter.h"
 #endif
 
-#if HAS_COLOR_LEDS
+#if ENABLED(PRINTER_EVENT_LEDS)
   #include "../../feature/leds/leds.h"
 #endif
 
@@ -190,11 +190,7 @@ void GcodeSuite::M109() {
         const uint8_t blue = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 255, 0);
         if (blue != old_blue) {
           old_blue = blue;
-          set_led_color(255, 0, blue
-            #if ENABLED(NEOPIXEL_RGBW_LED)
-              , 0, true
-            #endif
-          );
+          set_led_color(255, 0, blue);
         }
       }
     #endif
@@ -230,10 +226,11 @@ void GcodeSuite::M109() {
   if (wait_for_heatup) {
     LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
     #if ENABLED(PRINTER_EVENT_LEDS)
-      #if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
-        set_led_color(0, 0, 0, 255);  // Turn on the WHITE LED
-      #else
-        set_led_color(255, 255, 255); // Set LEDs All On
+      #if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632) || ENABLED(RGBW_LED)
+        set_led_color(LED_WHITE);
+      #endif
+      #if ENABLED(NEOPIXEL_LED)
+        set_neopixel_color(pixels.Color(NEO_WHITE));
       #endif
     #endif
   }

Marlin/src/gcode/temperature/M140_M190.cpp

@@ -132,11 +132,7 @@ void GcodeSuite::M190() {
         const uint8_t red = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 0, 255);
         if (red != old_red) {
           old_red = red;
-          set_led_color(red, 0, 255
-            #if ENABLED(NEOPIXEL_RGBW_LED)
-              , 0, true
-            #endif
-          );
+          set_led_color(red, 0, 255);
         }
       }
     #endif

Marlin/src/inc/Conditionals_LCD.h

@@ -483,6 +483,6 @@
 
   #define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
   #define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER))
-  #define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED))
+  #define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED))
 
 #endif // CONDITIONALS_LCD_H

Marlin/src/inc/SanityCheck.h

@@ -210,6 +210,8 @@
   #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
 #elif defined(ADVANCE)
   #error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
+#elif defined(NEOPIXEL_RGBW_LED)
+  #error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
 #endif
 
 /**
@@ -1100,12 +1102,12 @@ static_assert(1 >= 0
   #if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
     #error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
   #endif
-#elif ENABLED(NEOPIXEL_RGBW_LED)
+#elif ENABLED(NEOPIXEL_LED)
   #if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
-    #error "NEOPIXEL_RGBW_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
+    #error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
   #endif
-#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_RGBW_LED)
-  #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_RGBW_LED."
+#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_LED)
+  #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED."
 #endif
 
 /**