E3 V2 DWIN: Z-Offset, cleanup, versatility (#19384)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

Marlin/Configuration_adv.h

@@ -1572,6 +1572,7 @@
 #if ENABLED(BABYSTEPPING)
   //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
+  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
@@ -1582,7 +1583,6 @@
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
-    //#define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.

Marlin/src/lcd/dwin/e3v2/dwin.h

@@ -29,9 +29,16 @@
 #include "rotary_encoder.h"
 #include "../../../libs/BL24CXX.h"
 
-#include <stdint.h>
+#include "../../../inc/MarlinConfigPre.h"
 
-enum processID {
+#if ANY(HAS_HOTEND, HAS_HEATED_BED, HAS_FAN) && PREHEAT_COUNT
+  #define HAS_PREHEAT 1
+  #if PREHEAT_COUNT < 2
+    #error "Creality DWIN requires two material preheat presets."
+  #endif
+#endif
+
+enum processID : uint8_t {
   // Process ID
   MainMenu,
   SelectFile,
@@ -44,7 +51,7 @@ enum processID {
   Motion,
   Info,
   Tune,
-  #if HAS_HOTEND
+  #if HAS_PREHEAT
     PLAPreheat,
     ABSPreheat,
   #endif
@@ -218,7 +225,7 @@ enum processID {
 #define BarFill_Color     0x10E4  // fill color of progress bar
 #define Select_Color      0x33BB  // selected color
 
-extern int checkkey, last_checkkey;
+extern uint8_t checkkey;
 extern float zprobe_zoffset;
 extern char print_filename[16];
 
@@ -227,7 +234,7 @@ extern millis_t dwin_heat_time;
 typedef struct {
   TERN_(HAS_HOTEND,     int16_t E_Temp    = 0);
   TERN_(HAS_HEATED_BED, int16_t Bed_Temp  = 0);
-  TERN_(HAS_FAN,        int16_t Fan_speed = 0);
+  TERN_(HAS_PREHEAT,    int16_t Fan_speed = 0);
   int16_t print_speed     = 100;
   float Max_Feedspeed     = 0;
   float Max_Acceleration  = 0;
@@ -236,7 +243,7 @@ typedef struct {
   float Move_X_scale      = 0;
   float Move_Y_scale      = 0;
   float Move_Z_scale      = 0;
-  #if EXTRUDERS
+  #if HAS_HOTEND
     float Move_E_scale    = 0;
   #endif
   float offset_value      = 0;
@@ -246,33 +253,27 @@ typedef struct {
 typedef struct {
   bool language_chinese;  // 0: EN, 1: CN
   bool pause_flag:1;
+  bool pause_action:1;
   bool print_finish:1;
-  bool confirm_flag:1;
+  bool done_confirm_flag:1;
   bool select_flag:1;
   bool home_flag:1;
   bool heat_flag:1;  // 0: heating done  1: during heating
-  #if HAS_HOTEND
+  #if ENABLED(PREVENT_COLD_EXTRUSION)
     bool ETempTooLow_flag:1;
   #endif
   #if HAS_LEVELING
     bool leveling_offset_flag:1;
   #endif
   #if HAS_FAN
-    AxisEnum feedspeed_flag;
+    AxisEnum feedspeed_axis;
   #endif
-  AxisEnum acc_flag;
+  AxisEnum acc_axis, jerk_axis, step_axis;
-  AxisEnum jerk_flag;
-  AxisEnum step_flag;
 } HMI_Flag;
 
 extern HMI_value_t HMI_ValueStruct;
 extern HMI_Flag    HMI_flag;
 
-// Language
-void HMI_SetLanguage(void);
-void HMI_SetAndSaveLanguageWestern(void);
-void HMI_SetAndSaveLanguageChinese(void);
-
 // Show ICO
 void ICON_Print(bool show);
 void ICON_Prepare(bool show);
@@ -285,44 +286,47 @@ void ICON_Pause(bool show);
 void ICON_Continue(bool show);
 void ICON_Stop(bool show);
 
-// Popup window tips
+#if HAS_HOTEND || HAS_HEATED_BED
+  // Popup message window
+  void DWIN_Popup_Temperature(const bool toohigh);
+#endif
+
 #if HAS_HOTEND
-  void Popup_Window_Temperature(const bool toohigh);
+  void Popup_Window_ETempTooLow();
-  void Popup_Window_ETempTooLow(void);
 #endif
 
-void Popup_Window_Resume(void);
+void Popup_Window_Resume();
-void Popup_Window_Home(void);
+void Popup_Window_Home(const bool parking=false);
-void Popup_Window_Leveling(void);
+void Popup_Window_Leveling();
 
-void Goto_PrintProcess(void);
+void Goto_PrintProcess();
-void Goto_MainMenu(void);
+void Goto_MainMenu();
 
 // Variable control
-void HMI_Move_X(void);
+void HMI_Move_X();
-void HMI_Move_Y(void);
+void HMI_Move_Y();
-void HMI_Move_Z(void);
+void HMI_Move_Z();
-void HMI_Move_E(void);
+void HMI_Move_E();
 
-void HMI_Zoffset(void);
+void HMI_Zoffset();
 
-TERN_(HAS_HOTEND,     void HMI_ETemp(void));
+TERN_(HAS_HOTEND,     void HMI_ETemp());
-TERN_(HAS_HEATED_BED, void HMI_BedTemp(void));
+TERN_(HAS_HEATED_BED, void HMI_BedTemp());
-TERN_(HAS_FAN,        void HMI_FanSpeed(void));
+TERN_(HAS_FAN,        void HMI_FanSpeed());
 
-void HMI_PrintSpeed(void);
+void HMI_PrintSpeed();
 
-void HMI_MaxFeedspeedXYZE(void);
+void HMI_MaxFeedspeedXYZE();
-void HMI_MaxAccelerationXYZE(void);
+void HMI_MaxAccelerationXYZE();
-void HMI_MaxJerkXYZE(void);
+void HMI_MaxJerkXYZE();
-void HMI_StepXYZE(void);
+void HMI_StepXYZE();
 
-void update_variable(void);
+void update_variable();
 void DWIN_Draw_Signed_Float(uint8_t size, uint16_t bColor, uint8_t iNum, uint8_t fNum, uint16_t x, uint16_t y, long value);
 
 // SD Card
-void HMI_SDCardInit(void);
+void HMI_SDCardInit();
-void HMI_SDCardUpdate(void);
+void HMI_SDCardUpdate();
 
 // Main Process
 void Icon_print(bool value);
@@ -333,32 +337,32 @@ void Icon_leveling(bool value);
 // Other
 bool Pause_HeatStatus();
 void HMI_StartFrame(const bool with_update); // Startup screen
-void HMI_MainMenu(void);    // Main process screen
+void HMI_MainMenu();    // Main process screen
-void HMI_SelectFile(void);  // File page
+void HMI_SelectFile();  // File page
-void HMI_Printing(void);    // Print page
+void HMI_Printing();    // Print page
-void HMI_Prepare(void);     // Prepare page
+void HMI_Prepare();     // Prepare page
-void HMI_Control(void);     // Control page
+void HMI_Control();     // Control page
-void HMI_Leveling(void);    // Level the page
+void HMI_Leveling();    // Level the page
-void HMI_AxisMove(void);    // Axis movement menu
+void HMI_AxisMove();    // Axis movement menu
-void HMI_Temperature(void); // Temperature menu
+void HMI_Temperature(); // Temperature menu
-void HMI_Motion(void);      // Sports menu
+void HMI_Motion();      // Sports menu
-void HMI_Info(void);        // Information menu
+void HMI_Info();        // Information menu
-void HMI_Tune(void);        // Adjust the menu
+void HMI_Tune();        // Adjust the menu
-
+
-#if HAS_HOTEND
+#if HAS_PREHEAT
-  void HMI_PLAPreheatSetting(void); // PLA warm-up setting
+  void HMI_PLAPreheatSetting(); // PLA warm-up setting
-  void HMI_ABSPreheatSetting(void); // ABS warm-up setting
+  void HMI_ABSPreheatSetting(); // ABS warm-up setting
 #endif
 
-void HMI_MaxSpeed(void);        // Maximum speed submenu
+void HMI_MaxSpeed();        // Maximum speed submenu
-void HMI_MaxAcceleration(void); // Maximum acceleration submenu
+void HMI_MaxAcceleration(); // Maximum acceleration submenu
-void HMI_MaxJerk(void);         // Maximum jerk speed submenu
+void HMI_MaxJerk();         // Maximum jerk speed submenu
-void HMI_Step(void);            // Transmission ratio
+void HMI_Step();            // Transmission ratio
 
-void HMI_Init(void);
+void HMI_Init();
-void DWIN_Update(void);
+void DWIN_Update();
-void EachMomentUpdate(void);
+void EachMomentUpdate();
-void DWIN_HandleScreen(void);
+void DWIN_HandleScreen();
 
-void DWIN_CompletedHoming(void);
+void DWIN_CompletedHoming();
-void DWIN_CompletedLeveling(void);
+void DWIN_CompletedLeveling();

Marlin/src/lcd/dwin/e3v2/rotary_encoder.cpp

@@ -124,7 +124,7 @@ ENCODER_DiffState Encoder_ReceiveAnalyze(void) {
       int32_t encoderMultiplier = 1;
 
       // if must encoder rati multiplier
-      if (EncoderRate.encoderRateEnabled) {
+      if (EncoderRate.enabled) {
         const float abs_diff = ABS(temp_diff),
                     encoderMovementSteps = abs_diff / (ENCODER_PULSES_PER_STEP);
         if (EncoderRate.lastEncoderTime) {

Marlin/src/lcd/dwin/e3v2/rotary_encoder.h

@@ -44,7 +44,7 @@
 #define BUTTON_PRESSED(BN) !READ(BTN_## BN)
 
 typedef struct {
-  bool encoderRateEnabled = 0;
+  bool enabled = false;
   int encoderMoveValue = 0;
   millis_t lastEncoderTime = 0;
 } ENCODER_Rate;

Marlin/src/module/temperature.cpp

@@ -576,7 +576,7 @@ volatile bool Temperature::raw_temps_ready = false;
         #define MAX_CYCLE_TIME_PID_AUTOTUNE 20L
       #endif
       if ((ms - _MIN(t1, t2)) > (MAX_CYCLE_TIME_PID_AUTOTUNE * 60L * 1000L)) {
-        TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(0));
+        TERN_(DWIN_CREALITY_LCD, DWIN_Popup_Temperature(0));
         TERN_(EXTENSIBLE_UI, ExtUI::onPidTuning(ExtUI::result_t::PID_TUNING_TIMEOUT));
         SERIAL_ECHOLNPGM(STR_PID_TIMEOUT);
         break;
@@ -812,12 +812,16 @@ void Temperature::_temp_error(const heater_id_t heater_id, PGM_P const serial_ms
 }
 
 void Temperature::max_temp_error(const heater_id_t heater_id) {
-  TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(1));
+  #if ENABLED(DWIN_CREALITY_LCD) && (HAS_HOTEND || HAS_HEATED_BED)
+    DWIN_Popup_Temperature(1);
+  #endif
   _temp_error(heater_id, PSTR(STR_T_MAXTEMP), GET_TEXT(MSG_ERR_MAXTEMP));
 }
 
 void Temperature::min_temp_error(const heater_id_t heater_id) {
-  TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(0));
+  #if ENABLED(DWIN_CREALITY_LCD) && (HAS_HOTEND || HAS_HEATED_BED)
+    DWIN_Popup_Temperature(0);
+  #endif
   _temp_error(heater_id, PSTR(STR_T_MINTEMP), GET_TEXT(MSG_ERR_MINTEMP));
 }
 
@@ -1055,7 +1059,7 @@ void Temperature::manage_heater() {
         // Make sure temperature is increasing
         if (watch_hotend[e].next_ms && ELAPSED(ms, watch_hotend[e].next_ms)) {  // Time to check this extruder?
           if (degHotend(e) < watch_hotend[e].target) {                          // Failed to increase enough?
-            TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(0));
+            TERN_(DWIN_CREALITY_LCD, DWIN_Popup_Temperature(0));
             _temp_error((heater_id_t)e, str_t_heating_failed, GET_TEXT(MSG_HEATING_FAILED_LCD));
           }
           else                                                                  // Start again if the target is still far off
@@ -1098,7 +1102,7 @@ void Temperature::manage_heater() {
       // Make sure temperature is increasing
       if (watch_bed.elapsed(ms)) {        // Time to check the bed?
         if (degBed() < watch_bed.target) {                              // Failed to increase enough?
-          TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(0));
+          TERN_(DWIN_CREALITY_LCD, DWIN_Popup_Temperature(0));
           _temp_error(H_BED, str_t_heating_failed, GET_TEXT(MSG_HEATING_FAILED_LCD));
         }
         else                                                            // Start again if the target is still far off
@@ -2023,7 +2027,7 @@ void Temperature::init() {
         state = TRRunaway;
 
       case TRRunaway:
-        TERN_(DWIN_CREALITY_LCD, Popup_Window_Temperature(0));
+        TERN_(DWIN_CREALITY_LCD, DWIN_Popup_Temperature(0));
         _temp_error(heater_id, str_t_thermal_runaway, GET_TEXT(MSG_THERMAL_RUNAWAY));
     }
   }
@@ -2440,14 +2444,8 @@ void Temperature::tick() {
 
   #if DISABLED(SLOW_PWM_HEATERS)
 
-    #if HAS_HOTEND || HAS_HEATED_BED || HAS_HEATED_CHAMBER
+    #if ANY(HAS_HOTEND, HAS_HEATED_BED, HAS_HEATED_CHAMBER, FAN_SOFT_PWM)
-      constexpr uint8_t pwm_mask =
+      constexpr uint8_t pwm_mask = TERN0(SOFT_PWM_DITHER, _BV(SOFT_PWM_SCALE) - 1);
-        #if ENABLED(SOFT_PWM_DITHER)
-          _BV(SOFT_PWM_SCALE) - 1
-        #else
-          0
-        #endif
-      ;
       #define _PWM_MOD(N,S,T) do{                           \
         const bool on = S.add(pwm_mask, T.soft_pwm_amount); \
         WRITE_HEATER_##N(on);                               \

buildroot/share/PlatformIO/scripts/common-dependencies.h

@@ -89,10 +89,6 @@
   #define HAS_GCODE_M876
 #endif
 
-#if PREHEAT_COUNT
-  #define HAS_PREHEAT_COUNT
-#endif
-
 #if EXTRUDERS
   #define HAS_EXTRUDERS
   #if EXTRUDERS > 1

platformio.ini

@@ -153,7 +153,6 @@ default_src_filter = +<src/*> -<src/config> -<src/HAL> +<src/HAL/shared>
   -<src/gcode/host/M360.cpp>
   -<src/gcode/host/M876.cpp>
   -<src/gcode/lcd/M0_M1.cpp>
-  -<src/gcode/lcd/M145.cpp>
   -<src/gcode/lcd/M250.cpp>
   -<src/gcode/lcd/M73.cpp>
   -<src/gcode/lcd/M995.cpp>
@@ -330,7 +329,6 @@ HOST_KEEPALIVE_FEATURE  = src_filter=+<src/gcode/host/M113.cpp>
 REPETIER_GCODE_M360     = src_filter=+<src/gcode/host/M360.cpp>
 HAS_GCODE_M876          = src_filter=+<src/gcode/host/M876.cpp>
 HAS_RESUME_CONTINUE     = src_filter=+<src/gcode/lcd/M0_M1.cpp>
-HAS_PREHEAT_COUNT       = src_filter=+<src/gcode/lcd/M145.cpp>
 HAS_LCD_CONTRAST        = src_filter=+<src/gcode/lcd/M250.cpp>
 LCD_SET_PROGRESS_MANUALLY = src_filter=+<src/gcode/lcd/M73.cpp>
 TOUCH_SCREEN_CALIBRATION = src_filter=+<src/gcode/lcd/M995.cpp>