Add M114_DETAIL to Configuration_adv.h

Marlin/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/default/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 4

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 3

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 1

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 3
 #define Y_HOME_BUMP_MM 3
 #define Z_HOME_BUMP_MM 3

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -334,7 +337,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -135,6 +135,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -358,7 +361,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 10
 #define Y_HOME_BUMP_MM 10
 #define Z_HOME_BUMP_MM 3

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

@@ -127,6 +127,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -350,7 +353,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 5 // deltas need the same for all three axes

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 2
 #define Y_HOME_BUMP_MM 2
 #define Z_HOME_BUMP_MM 2 // deltas need the same for all three axes

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 1

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -122,6 +122,9 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+// Show extra position information in M114
+//#define M114_DETAIL
+
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
 //#define SHOW_TEMP_ADC_VALUES
@@ -345,7 +348,7 @@
 
 // @section homing
 
-//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+// Homing hits each endstop, retracts by these distances, then does a slower bump.
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2

Marlin/src/gcode/host/M114.cpp

@@ -26,7 +26,7 @@
 #include "../../module/motion.h"
 #include "../../module/stepper.h"
 
-#ifdef M114_DETAIL
+#if ENABLED(M114_DETAIL)
 
   void report_xyze(const float pos[XYZE], const uint8_t n = 4, const uint8_t precision = 3) {
     char str[12];
@@ -111,7 +111,7 @@
  */
 void GcodeSuite::M114() {
 
-  #ifdef M114_DETAIL
+  #if ENABLED(M114_DETAIL)
     if (parser.seen('D')) {
       report_current_position_detail();
       return;