Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

112 lines
3.2 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* Arduino Mega with RAMPS v1.4 for Anycubic
*/
#define BOARD_NAME "Anycubic RAMPS 1.4"
//
// Servos
//
#if MB(TRIGORILLA_14_11)
#define SERVO0_PIN 5
#define SERVO1_PIN 4
#define SERVO2_PIN 11
#define SERVO3_PIN 6
#endif
// Labeled pins
#define TRIGORILLA_HEATER_BED_PIN 8
#define TRIGORILLA_HEATER_0_PIN 10
#define TRIGORILLA_HEATER_1_PIN 45 // Anycubic Kossel: Unused
#define TRIGORILLA_FAN0_PIN 9 // Anycubic Kossel: Usually the part cooling fan
#define TRIGORILLA_FAN1_PIN 7 // Anycubic Kossel: Unused
#define TRIGORILLA_FAN2_PIN 44 // Anycubic Kossel: Hotend fan
// Remap MOSFET pins to common usages:
#define RAMPS_D10_PIN TRIGORILLA_HEATER_0_PIN // HEATER_0_PIN is always RAMPS_D10_PIN in pins_RAMPS.h
#if HOTENDS > 1 // EEF and EEB
#define RAMPS_D9_PIN TRIGORILLA_HEATER_1_PIN
#if !TEMP_SENSOR_BED
// EEF
#define RAMPS_D8_PIN TRIGORILLA_FAN0_PIN
#else
// EEB
#define RAMPS_D8_PIN TRIGORILLA_HEATER_BED_PIN
#define FAN_PIN TRIGORILLA_FAN0_PIN // Override pin 4 in pins_RAMPS.h
#endif
#elif TEMP_SENSOR_BED
// EFB (Anycubic Kossel default)
#define RAMPS_D9_PIN TRIGORILLA_FAN0_PIN
#define RAMPS_D8_PIN TRIGORILLA_HEATER_BED_PIN
#else
// EFF
#define RAMPS_D9_PIN TRIGORILLA_FAN1_PIN
#define RAMPS_D8_PIN TRIGORILLA_FAN0_PIN
#endif
#if HOTENDS > 1 || TEMP_SENSOR_BED // EEF, EEB, EFB
#define FAN1_PIN TRIGORILLA_FAN1_PIN
#endif
#define FAN2_PIN TRIGORILLA_FAN2_PIN
#define ORIG_E0_AUTO_FAN_PIN TRIGORILLA_FAN2_PIN // Used in Anycubic Kossel example config
#include "pins_RAMPS.h"
//
// AnyCubic made the following changes to 1.1.0-RC8
// If these are appropriate for your LCD let us know.
//
#if 0 && HAS_SPI_LCD
// LCD Display output pins
#if BOTH(NEWPANEL, PANEL_ONE)
#undef LCD_PINS_D6
#define LCD_PINS_D6 57
#endif
// LCD Display input pins
#if ENABLED(NEWPANEL)
#if ANY(VIKI2, miniVIKI)
#undef DOGLCD_A0
#define DOGLCD_A0 23
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#undef BEEPER_PIN
#define BEEPER_PIN 33
#undef LCD_BACKLIGHT_PIN
#define LCD_BACKLIGHT_PIN 67
#endif
#elif ENABLED(MINIPANEL)
#undef BEEPER_PIN
#define BEEPER_PIN 33
#undef DOGLCD_A0
#define DOGLCD_A0 42
#endif
#endif // HAS_SPI_LCD