Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

417 lines
12 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* power_loss_recovery.cpp - Resume an SD print after power-loss
*/
#include "../inc/MarlinConfigPre.h"
#if ENABLED(POWER_LOSS_RECOVERY)
#include "power_loss_recovery.h"
#include "../core/macros.h"
bool PrintJobRecovery::enabled; // Initialized by settings.load()
SdFile PrintJobRecovery::file;
job_recovery_info_t PrintJobRecovery::info;
#include "../sd/cardreader.h"
#include "../lcd/ultralcd.h"
#include "../gcode/queue.h"
#include "../gcode/gcode.h"
#include "../module/motion.h"
#include "../module/planner.h"
#include "../module/printcounter.h"
#include "../module/temperature.h"
#include "../core/serial.h"
#if ENABLED(FWRETRACT)
#include "fwretract.h"
#endif
PrintJobRecovery recovery;
/**
* Clear the recovery info
*/
void PrintJobRecovery::init() { memset(&info, 0, sizeof(info)); }
/**
* Enable or disable then call changed()
*/
void PrintJobRecovery::enable(const bool onoff) {
enabled = onoff;
changed();
}
/**
* The enabled state was changed:
* - Enabled: Purge the job recovery file
* - Disabled: Write the job recovery file
*/
void PrintJobRecovery::changed() {
if (!enabled)
purge();
else if (IS_SD_PRINTING())
save(true);
}
/**
* Check for Print Job Recovery during setup()
*
* If a saved state exists send 'M1000 S' to initiate job recovery.
*/
void PrintJobRecovery::check() {
if (enabled) {
if (!card.flag.cardOK) card.initsd();
if (card.flag.cardOK) {
load();
if (!valid()) return purge();
enqueue_and_echo_commands_P(PSTR("M1000 S"));
}
}
}
/**
* Delete the recovery file and clear the recovery data
*/
void PrintJobRecovery::purge() {
init();
card.removeJobRecoveryFile();
}
/**
* Load the recovery data, if it exists
*/
void PrintJobRecovery::load() {
if (exists()) {
open(true);
(void)file.read(&info, sizeof(info));
close();
}
#if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
debug(PSTR("Load"));
#endif
}
/**
* Save the current machine state to the power-loss recovery file
*/
void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=true*/) {
#if SAVE_INFO_INTERVAL_MS > 0
static millis_t next_save_ms; // = 0
millis_t ms = millis();
#endif
if (force
#if DISABLED(SAVE_EACH_CMD_MODE) // Always save state when enabled
#if PIN_EXISTS(POWER_LOSS) // Save if power loss pin is triggered
|| READ(POWER_LOSS_PIN) == POWER_LOSS_STATE
#endif
#if SAVE_INFO_INTERVAL_MS > 0 // Save if interval is elapsed
|| ELAPSED(ms, next_save_ms)
#endif
// Save every time Z is higher than the last call
|| current_position[Z_AXIS] > info.current_position[Z_AXIS]
#endif
) {
#if SAVE_INFO_INTERVAL_MS > 0
next_save_ms = ms + SAVE_INFO_INTERVAL_MS;
#endif
// Set Head and Foot to matching non-zero values
if (!++info.valid_head) ++info.valid_head; // non-zero in sequence
//if (!IS_SD_PRINTING()) info.valid_head = 0;
info.valid_foot = info.valid_head;
// Machine state
COPY(info.current_position, current_position);
info.feedrate = uint16_t(feedrate_mm_s * 60.0f);
#if HOTENDS > 1
info.active_hotend = active_extruder;
#endif
COPY(info.target_temperature, thermalManager.target_temperature);
#if HAS_HEATED_BED
info.target_temperature_bed = thermalManager.target_temperature_bed;
#endif
#if FAN_COUNT
COPY(info.fan_speed, fan_speed);
#endif
#if HAS_LEVELING
info.leveling = planner.leveling_active;
info.fade = (
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
planner.z_fade_height
#else
0
#endif
);
#endif
#if ENABLED(FWRETRACT)
COPY(info.retract, fwretract.current_retract);
info.retract_hop = fwretract.current_hop;
#endif
// Commands in the queue
info.commands_in_queue = save_queue ? commands_in_queue : 0;
info.cmd_queue_index_r = cmd_queue_index_r;
COPY(info.command_queue, command_queue);
// Elapsed print job time
info.print_job_elapsed = print_job_timer.duration();
// SD file position
card.getAbsFilename(info.sd_filename);
info.sdpos = card.getIndex();
write();
// KILL now if the power-loss pin was triggered
#if PIN_EXISTS(POWER_LOSS)
if (READ(POWER_LOSS_PIN) == POWER_LOSS_STATE) kill(PSTR(MSG_OUTAGE_RECOVERY));
#endif
}
}
/**
* Save the recovery info the recovery file
*/
void PrintJobRecovery::write() {
#if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
debug(PSTR("Write"));
#endif
open(false);
file.seekSet(0);
const int16_t ret = file.write(&info, sizeof(info));
#if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
if (ret == -1) SERIAL_ECHOLNPGM("Power-loss file write failed.");
#else
UNUSED(ret);
#endif
}
/**
* Resume the saved print job
*/
void PrintJobRecovery::resume() {
#define RECOVERY_ZRAISE 2
#if HAS_LEVELING
// Make sure leveling is off before any G92 and G28
gcode.process_subcommands_now_P(PSTR("M420 S0 Z0"));
#endif
// Set Z to 0, raise Z by 2mm, and Home (XY only for Cartesian) with no raise
// (Only do simulated homing in Marlin Dev Mode.)
gcode.process_subcommands_now_P(PSTR("G92.0 Z0|G1 Z" STRINGIFY(RECOVERY_ZRAISE) "|G28 R0"
#if ENABLED(MARLIN_DEV_MODE)
" S"
#elif !IS_KINEMATIC
" X Y"
#endif
));
// Pretend that all axes are homed
axis_homed = axis_known_position = xyz_bits;
char cmd[40], str_1[16], str_2[16];
// Select the previously active tool (with no_move)
#if EXTRUDERS > 1
sprintf_P(cmd, PSTR("T%i S"), info.active_hotend);
gcode.process_subcommands_now(cmd);
#endif
#if HAS_HEATED_BED
const int16_t bt = info.target_temperature_bed;
if (bt) {
// Restore the bed temperature
sprintf_P(cmd, PSTR("M190 S%i"), bt);
gcode.process_subcommands_now(cmd);
}
#endif
// Restore all hotend temperatures
HOTEND_LOOP() {
const int16_t et = info.target_temperature[e];
if (et) {
#if HOTENDS > 1
sprintf_P(cmd, PSTR("T%i"), e);
gcode.process_subcommands_now(cmd);
#endif
sprintf_P(cmd, PSTR("M109 S%i"), et);
gcode.process_subcommands_now(cmd);
}
}
// Restore print cooling fan speeds
6 years ago
FANS_LOOP(i) {
uint8_t f = info.fan_speed[i];
if (f) {
sprintf_P(cmd, PSTR("M106 P%i S%i"), i, f);
gcode.process_subcommands_now(cmd);
}
}
// Restore retract and hop state
#if ENABLED(FWRETRACT)
for (uint8_t e = 0; e < EXTRUDERS; e++) {
if (info.retract[e] != 0.0)
fwretract.current_retract[e] = info.retract[e];
fwretract.retracted[e] = true;
}
fwretract.current_hop = info.retract_hop;
#endif
#if HAS_LEVELING
// Restore leveling state before 'G92 Z' to ensure
// the Z stepper count corresponds to the native Z.
if (info.fade || info.leveling) {
dtostrf(info.fade, 1, 1, str_1);
sprintf_P(cmd, PSTR("M420 S%i Z%s"), int(info.leveling), str_1);
gcode.process_subcommands_now(cmd);
}
#endif
// Restore Z (plus raise) and E positions with G92.0
dtostrf(info.current_position[Z_AXIS] + RECOVERY_ZRAISE, 1, 3, str_1);
dtostrf(info.current_position[E_AXIS]
#if ENABLED(SAVE_EACH_CMD_MODE)
- 5 // Extra extrusion on restart
#endif
, 1, 3, str_2
);
sprintf_P(cmd, PSTR("G92.0 Z%s E%s"), str_1, str_2);
gcode.process_subcommands_now(cmd);
// Move back to the saved XY
dtostrf(info.current_position[X_AXIS], 1, 3, str_1);
dtostrf(info.current_position[Y_AXIS], 1, 3, str_2);
sprintf_P(cmd, PSTR("G1 X%s Y%s F3000"), str_1, str_2);
gcode.process_subcommands_now(cmd);
// Move back to the saved Z
dtostrf(info.current_position[Z_AXIS], 1, 3, str_1);
sprintf_P(cmd, PSTR("G1 Z%s F200"), str_1);
gcode.process_subcommands_now(cmd);
// Restore the feedrate
sprintf_P(cmd, PSTR("G1 F%d"), info.feedrate);
gcode.process_subcommands_now(cmd);
// Process commands from the old pending queue
uint8_t c = info.commands_in_queue, r = info.cmd_queue_index_r;
for (; c--; r = (r + 1) % BUFSIZE)
gcode.process_subcommands_now(info.command_queue[r]);
// Resume the SD file from the last position
char *fn = info.sd_filename;
while (*fn == '/') fn++;
sprintf_P(cmd, PSTR("M23 %s"), fn);
gcode.process_subcommands_now(cmd);
sprintf_P(cmd, PSTR("M24 S%ld T%ld"), info.sdpos, info.print_job_elapsed);
gcode.process_subcommands_now(cmd);
}
#if ENABLED(DEBUG_POWER_LOSS_RECOVERY)
void PrintJobRecovery::debug(PGM_P const prefix) {
serialprintPGM(prefix);
SERIAL_ECHOPAIR(" Job Recovery Info...\nvalid_head:", int(info.valid_head));
SERIAL_ECHOLNPAIR(" valid_foot:", int(info.valid_foot));
if (info.valid_head) {
if (info.valid_head == info.valid_foot) {
SERIAL_ECHOPGM("current_position: ");
LOOP_XYZE(i) {
SERIAL_ECHO(info.current_position[i]);
if (i < E_AXIS) SERIAL_CHAR(',');
}
SERIAL_EOL();
SERIAL_ECHOLNPAIR("feedrate: ", info.feedrate);
#if HOTENDS > 1
SERIAL_ECHOLNPAIR("active_hotend: ", int(info.active_hotend));
#endif
SERIAL_ECHOPGM("target_temperature: ");
HOTEND_LOOP() {
SERIAL_ECHO(info.target_temperature[e]);
if (e < HOTENDS - 1) SERIAL_CHAR(',');
}
SERIAL_EOL();
#if HAS_HEATED_BED
SERIAL_ECHOLNPAIR("target_temperature_bed: ", info.target_temperature_bed);
#endif
#if FAN_COUNT
SERIAL_ECHOPGM("fan_speed: ");
for (int8_t i = 0; i < FAN_COUNT; i++) {
SERIAL_ECHO(int(info.fan_speed[i]));
if (i < FAN_COUNT - 1) SERIAL_CHAR(',');
}
SERIAL_EOL();
#endif
#if HAS_LEVELING
SERIAL_ECHOPAIR("leveling: ", int(info.leveling));
SERIAL_ECHOLNPAIR(" fade: ", int(info.fade));
#endif
#if ENABLED(FWRETRACT)
SERIAL_ECHOPGM("retract: ");
for (int8_t e = 0; e < EXTRUDERS; e++) {
SERIAL_ECHO(info.retract[e]);
if (e < EXTRUDERS - 1) SERIAL_CHAR(',');
}
SERIAL_EOL();
SERIAL_ECHOLNPAIR("retract_hop: ", info.retract_hop);
#endif
SERIAL_ECHOLNPAIR("cmd_queue_index_r: ", int(info.cmd_queue_index_r));
SERIAL_ECHOLNPAIR("commands_in_queue: ", int(info.commands_in_queue));
for (uint8_t i = 0; i < info.commands_in_queue; i++) SERIAL_ECHOLNPAIR("> ", info.command_queue[i]);
SERIAL_ECHOLNPAIR("sd_filename: ", info.sd_filename);
SERIAL_ECHOLNPAIR("sdpos: ", info.sdpos);
SERIAL_ECHOLNPAIR("print_job_elapsed: ", info.print_job_elapsed);
}
else
SERIAL_ECHOLNPGM("INVALID DATA");
}
SERIAL_ECHOLNPGM("---");
}
#endif // DEBUG_POWER_LOSS_RECOVERY
#endif // POWER_LOSS_RECOVERY