Marlin_FB4S/ArduinoAddons/Arduino_1.6.x/libraries/L6470/L6470.h

////////////////////////////////////////////////////////////
//ORIGINAL CODE 12/12/2011- Mike Hord, SparkFun Electronics
//LIBRARY Created by Adam Meyer of bildr Aug 18th 2012
//Released as MIT license
////////////////////////////////////////////////////////////
#ifndef L6470_h
#define L6470_h

#include <Arduino.h>
#include <SPI.h>

#define SLAVE_SELECT_PIN 38 // Wire this to the CSN pin
// #define RESET 6 // Wire this to the STBY line
#define BUSYN 7 // Wire this to the BSYN line

// constant definitions for overcurrent thresholds. Write these values to
// register dSPIN_OCD_TH to set the level at which an overcurrent even occurs.
#define OCD_TH_375mA 0x00
#define OCD_TH_750mA 0x01
#define OCD_TH_1125mA 0x02
#define OCD_TH_1500mA 0x03
#define OCD_TH_1875mA 0x04
#define OCD_TH_2250mA 0x05
#define OCD_TH_2625mA 0x06
#define OCD_TH_3000mA 0x07
#define OCD_TH_3375mA 0x08
#define OCD_TH_3750mA 0x09
#define OCD_TH_4125mA 0x0A
#define OCD_TH_4500mA 0x0B
#define OCD_TH_4875mA 0x0C
#define OCD_TH_5250mA 0x0D
#define OCD_TH_5625mA 0x0E
#define OCD_TH_6000mA 0x0F

// STEP_MODE option values.
// First comes the "microsteps per step" options...
#define STEP_MODE_STEP_SEL 0x07 // Mask for these bits only.
#define STEP_SEL_1 0x00
#define STEP_SEL_1_2 0x01
#define STEP_SEL_1_4 0x02
#define STEP_SEL_1_8 0x03
#define STEP_SEL_1_16 0x04
#define STEP_SEL_1_32 0x05
#define STEP_SEL_1_64 0x06
#define STEP_SEL_1_128 0x07

// ...next, define the SYNC_EN bit. When set, the BUSYN pin will instead
// output a clock related to the full-step frequency as defined by the
// SYNC_SEL bits below.
#define STEP_MODE_SYNC_EN 0x80 // Mask for this bit
#define SYNC_EN 0x80

// ...last, define the SYNC_SEL modes. The clock output is defined by
// the full-step frequency and the value in these bits- see the datasheet
// for a matrix describing that relationship (page 46).
#define STEP_MODE_SYNC_SEL 0x70
#define SYNC_SEL_1_2 0x00
#define SYNC_SEL_1 0x10
#define SYNC_SEL_2 0x20
#define SYNC_SEL_4 0x30
#define SYNC_SEL_8 0x40
#define SYNC_SEL_16 0x50
#define SYNC_SEL_32 0x60
#define SYNC_SEL_64 0x70

// Bit names for the ALARM_EN register.
// Each of these bits defines one potential alarm condition.
// When one of these conditions occurs and the respective bit in ALARM_EN is set,
// the FLAG pin will go low. The register must be queried to determine which event
// caused the alarm.
#define ALARM_EN_OVERCURRENT 0x01
#define ALARM_EN_THERMAL_SHUTDOWN 0x02
#define ALARM_EN_THERMAL_WARNING 0x04
#define ALARM_EN_UNDER_VOLTAGE 0x08
#define ALARM_EN_STALL_DET_A 0x10
#define ALARM_EN_STALL_DET_B 0x20
#define ALARM_EN_SW_TURN_ON 0x40
#define ALARM_EN_WRONG_NPERF_CMD 0x80

// CONFIG register renames.

// Oscillator options.
// The dSPIN needs to know what the clock frequency is because it uses that for some
// calculations during operation.
#define CONFIG_OSC_SEL 0x000F // Mask for this bit field.
#define CONFIG_INT_16MHZ 0x0000 // Internal 16MHz, no output
#define CONFIG_INT_16MHZ_OSCOUT_2MHZ 0x0008 // Default; internal 16MHz, 2MHz output
#define CONFIG_INT_16MHZ_OSCOUT_4MHZ 0x0009 // Internal 16MHz, 4MHz output
#define CONFIG_INT_16MHZ_OSCOUT_8MHZ 0x000A // Internal 16MHz, 8MHz output
#define CONFIG_INT_16MHZ_OSCOUT_16MHZ 0x000B // Internal 16MHz, 16MHz output
#define CONFIG_EXT_8MHZ_XTAL_DRIVE 0x0004 // External 8MHz crystal
#define CONFIG_EXT_16MHZ_XTAL_DRIVE 0x0005 // External 16MHz crystal
#define CONFIG_EXT_24MHZ_XTAL_DRIVE 0x0006 // External 24MHz crystal
#define CONFIG_EXT_32MHZ_XTAL_DRIVE 0x0007 // External 32MHz crystal
#define CONFIG_EXT_8MHZ_OSCOUT_INVERT 0x000C // External 8MHz crystal, output inverted
#define CONFIG_EXT_16MHZ_OSCOUT_INVERT 0x000D // External 16MHz crystal, output inverted
#define CONFIG_EXT_24MHZ_OSCOUT_INVERT 0x000E // External 24MHz crystal, output inverted
#define CONFIG_EXT_32MHZ_OSCOUT_INVERT 0x000F // External 32MHz crystal, output inverted

// Configure the functionality of the external switch input
#define CONFIG_SW_MODE 0x0010 // Mask for this bit.
#define CONFIG_SW_HARD_STOP 0x0000 // Default; hard stop motor on switch.
#define CONFIG_SW_USER 0x0010 // Tie to the GoUntil and ReleaseSW
                                                    // commands to provide jog function.
                                                    // See page 25 of datasheet.

// Configure the motor voltage compensation mode (see page 34 of datasheet)
#define CONFIG_EN_VSCOMP 0x0020 // Mask for this bit.
#define CONFIG_VS_COMP_DISABLE 0x0000 // Disable motor voltage compensation.
#define CONFIG_VS_COMP_ENABLE 0x0020 // Enable motor voltage compensation.

// Configure overcurrent detection event handling
#define CONFIG_OC_SD 0x0080 // Mask for this bit.
#define CONFIG_OC_SD_DISABLE 0x0000 // Bridges do NOT shutdown on OC detect
#define CONFIG_OC_SD_ENABLE 0x0080 // Bridges shutdown on OC detect

// Configure the slew rate of the power bridge output
#define CONFIG_POW_SR 0x0300 // Mask for this bit field.
#define CONFIG_SR_180V_us 0x0000 // 180V/us
#define CONFIG_SR_290V_us 0x0200 // 290V/us
#define CONFIG_SR_530V_us 0x0300 // 530V/us

// Integer divisors for PWM sinewave generation
// See page 32 of the datasheet for more information on this.
#define CONFIG_F_PWM_DEC 0x1C00 // mask for this bit field
#define CONFIG_PWM_MUL_0_625 (0x00)<<10
#define CONFIG_PWM_MUL_0_75 (0x01)<<10
#define CONFIG_PWM_MUL_0_875 (0x02)<<10
#define CONFIG_PWM_MUL_1 (0x03)<<10
#define CONFIG_PWM_MUL_1_25 (0x04)<<10
#define CONFIG_PWM_MUL_1_5 (0x05)<<10
#define CONFIG_PWM_MUL_1_75 (0x06)<<10
#define CONFIG_PWM_MUL_2 (0x07)<<10

// Multiplier for the PWM sinewave frequency
#define CONFIG_F_PWM_INT 0xE000 // mask for this bit field.
#define CONFIG_PWM_DIV_1 (0x00)<<13
#define CONFIG_PWM_DIV_2 (0x01)<<13
#define CONFIG_PWM_DIV_3 (0x02)<<13
#define CONFIG_PWM_DIV_4 (0x03)<<13
#define CONFIG_PWM_DIV_5 (0x04)<<13
#define CONFIG_PWM_DIV_6 (0x05)<<13
#define CONFIG_PWM_DIV_7 (0x06)<<13

// Status register bit renames- read-only bits conferring information about the
// device to the user.
#define STATUS_HIZ 0x0001 // high when bridges are in HiZ mode
#define STATUS_BUSY 0x0002 // mirrors BUSY pin
#define STATUS_SW_F 0x0004 // low when switch open, high when closed
#define STATUS_SW_EVN 0x0008 // active high, set on switch falling edge,
                                                    // cleared by reading STATUS
#define STATUS_DIR 0x0010 // Indicates current motor direction.
                                                    // High is FWD, Low is REV.
#define STATUS_NOTPERF_CMD 0x0080 // Last command not performed.
#define STATUS_WRONG_CMD 0x0100 // Last command not valid.
#define STATUS_UVLO 0x0200 // Undervoltage lockout is active
#define STATUS_TH_WRN 0x0400 // Thermal warning
#define STATUS_TH_SD 0x0800 // Thermal shutdown
#define STATUS_OCD 0x1000 // Overcurrent detected
#define STATUS_STEP_LOSS_A 0x2000 // Stall detected on A bridge
#define STATUS_STEP_LOSS_B 0x4000 // Stall detected on B bridge
#define STATUS_SCK_MOD 0x8000 // Step clock mode is active

// Status register motor status field
#define STATUS_MOT_STATUS 0x0060 // field mask
#define STATUS_MOT_STATUS_STOPPED (0x0000)<<13 // Motor stopped
#define STATUS_MOT_STATUS_ACCELERATION (0x0001)<<13 // Motor accelerating
#define STATUS_MOT_STATUS_DECELERATION (0x0002)<<13 // Motor decelerating
#define STATUS_MOT_STATUS_CONST_SPD (0x0003)<<13 // Motor at constant speed

// Register address redefines.
// See the Param_Handler() function for more info about these.
#define ABS_POS 0x01
#define EL_POS 0x02
#define MARK 0x03
#define SPEED 0x04
#define ACC 0x05
#define DEC 0x06
#define MAX_SPEED 0x07
#define MIN_SPEED 0x08
#define FS_SPD 0x15
#define KVAL_HOLD 0x09
#define KVAL_RUN 0x0A
#define KVAL_ACC 0x0B
#define KVAL_DEC 0x0C
#define INT_SPD 0x0D
#define ST_SLP 0x0E
#define FN_SLP_ACC 0x0F
#define FN_SLP_DEC 0x10
#define K_THERM 0x11
#define ADC_OUT 0x12
#define OCD_TH 0x13
#define STALL_TH 0x14
#define STEP_MODE 0x16
#define ALARM_EN 0x17
#define CONFIG 0x18
#define STATUS 0x19

//dSPIN commands
#define NOP 0x00
#define SET_PARAM 0x00
#define GET_PARAM 0x20
#define RUN 0x50
#define STEP_CLOCK 0x58
#define MOVE 0x40
#define GOTO 0x60
#define GOTO_DIR 0x68
#define GO_UNTIL 0x82
#define RELEASE_SW 0x92
#define GO_HOME 0x70
#define GO_MARK 0x78
#define RESET_POS 0xD8
#define RESET_DEVICE 0xC0
#define SOFT_STOP 0xB0
#define HARD_STOP 0xB8
#define SOFT_HIZ 0xA0
#define HARD_HIZ 0xA8
#define GET_STATUS 0xD0

/* dSPIN direction options */
#define FWD 0x01
#define REV 0x00

/* dSPIN action options */
#define ACTION_RESET 0x00
#define ACTION_COPY 0x01


class L6470{

  public:

    L6470(int SSPin);
    void init(int k_value);
    void setMicroSteps(int microSteps);
    void setCurrent(int current);
    void setMaxSpeed(int speed);
    void setMinSpeed(int speed);
    void setAcc(float acceleration);
    void setDec(float deceleration);
    void setOverCurrent(unsigned int ma_current);
    void setThresholdSpeed(float threshold);
    void setStallCurrent(float ma_current);
    
    unsigned long ParamHandler(byte param, unsigned long value);
    void SetLowSpeedOpt(boolean enable);
    void run(byte dir, float spd);
    void Step_Clock(byte dir);
    void goHome();
    void setAsHome();
    void goMark();
    void move(long n_step);
    void goTo(long pos);
    void goTo_DIR(byte dir, long pos);
    void goUntil(byte act, byte dir, unsigned long spd);
    boolean isBusy();
    void releaseSW(byte act, byte dir);
    float getSpeed();
    long getPos();
    void setMark();
    void setMark(long value);
    void resetPos();
    void resetDev();
    void softStop();
    void hardStop();
    void softFree();
    void free();
    int getStatus();
	void SetParam(byte param, unsigned long value);

  private:
    long convert(unsigned long val);
    unsigned long GetParam(byte param);
    unsigned long AccCalc(float stepsPerSecPerSec);
    unsigned long DecCalc(float stepsPerSecPerSec);
    unsigned long MaxSpdCalc(float stepsPerSec);
    unsigned long MinSpdCalc(float stepsPerSec);
    unsigned long FSCalc(float stepsPerSec);
    unsigned long IntSpdCalc(float stepsPerSec);
    unsigned long SpdCalc(float stepsPerSec);
    unsigned long Param(unsigned long value, byte bit_len);
    byte Xfer(byte data);
    int _SSPin;
};

#endif