Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

257 lines
9.0 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* ARCHIM2 pin assignment
*
* The Archim 2.0 board requires Arduino Archim addons installed.
*
* - Add the following URL to Arduino IDE's Additional Board Manager URLs:
* https://raw.githubusercontent.com/ultimachine/ArduinoAddons/master/package_ultimachine_index.json
*
* - In the Arduino IDE Board Manager search for Archim and install the package.
*
* - Change your target board to "Archim".
*
* Further information on the UltiMachine website...
* https://github.com/ultimachine/Archim/wiki
*/
#if NOT_TARGET(__SAM3X8E__)
#error "Oops! Select 'Archim' in 'Tools > Board.'"
#elif DISABLED(TMC_USE_SW_SPI)
#error "Archim2 requires Software SPI. Enable TMC_USE_SW_SPI in Configuration_adv.h."
#endif
#define BOARD_INFO_NAME "Archim 2.0"
//
// Items marked * have been altered from Archim v1.0
//
//
// Servos
//
#define SERVO0_PIN 20 // D20 PB12 (Header J20 20)
#define SERVO1_PIN 21 // D21 PB13 (Header J20 19)
//
// Limit Switches
//
#if ENABLED(SENSORLESS_HOMING)
// Only use Diag Pins when SENSORLESS_HOMING is enabled for the TMC2130 drivers.
// Otherwise use a physical endstop based configuration.
// TMC2130 Diag Pins
#define X_DIAG_PIN 59 // PA4
#define Y_DIAG_PIN 48 // PC15
#define Z_DIAG_PIN 36 // PC4
#define E0_DIAG_PIN 78 // PB23
#define E1_DIAG_PIN 25 // PD0
#if X_HOME_TO_MIN
#define X_MIN_PIN X_DIAG_PIN
#define X_MAX_PIN 32
#else
#define X_MIN_PIN 14
#define X_MAX_PIN X_DIAG_PIN
#endif
#if Y_HOME_TO_MIN
#define Y_MIN_PIN Y_DIAG_PIN
#define Y_MAX_PIN 15
#else
#define Y_MIN_PIN 29
#define Y_MAX_PIN Y_DIAG_PIN
#endif
#else
#define X_MIN_PIN 14 // PD4 MIN ES1
#define X_MAX_PIN 32 // PD10 MAX ES1
#define Y_MIN_PIN 29 // PD6 MIN ES2
#define Y_MAX_PIN 15 // PD5 MAX ES2
#endif
#define Z_MIN_PIN 31 // PA7 MIN ES3
#define Z_MAX_PIN 30 // PD9 MAX ES3
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 32
#endif
//
// Steppers
//
#define X_STEP_PIN 38 // PC6 X-STEP *
#define X_DIR_PIN 37 // PC5 X-DIR *
#define X_ENABLE_PIN 41 // PC9 EN1
#ifndef X_CS_PIN
#define X_CS_PIN 39 // PC7 X_nCS
#endif
#define Y_STEP_PIN 51 // PC12 Y-STEP *
#define Y_DIR_PIN 92 // PC11 Y-DIR -AddOns *
#define Y_ENABLE_PIN 49 // PC14 Y-EN *
#ifndef Y_CS_PIN
#define Y_CS_PIN 50 // PC13 Y_nCS
#endif
#define Z_STEP_PIN 46 // PC17 Z-STEP *
#define Z_DIR_PIN 47 // PC16 Z-DIR *
#define Z_ENABLE_PIN 44 // PC19 Z-END *
#ifndef Z_CS_PIN
#define Z_CS_PIN 45 // PC18 Z_nCS
#endif
#define E0_STEP_PIN 107 // PB10 E1-STEP -AddOns *
#define E0_DIR_PIN 96 // PC10 E1-DIR -AddOns *
#define E0_ENABLE_PIN 105 // PB22 E1-EN -AddOns *
#ifndef E0_CS_PIN
#define E0_CS_PIN 104 // PC20 E1_nCS -AddOns *
#endif
#define E1_STEP_PIN 22 // PB26 E2_STEP *
#define E1_DIR_PIN 97 // PB24 E2_DIR -AddOns *
#define E1_ENABLE_PIN 18 // PA11 E2-EN
#ifndef E1_CS_PIN
#define E1_CS_PIN 19 // PA10 E2_nCS
#endif
//
// Software SPI pins for TMC2130 stepper drivers.
// Required for the Archim2 board.
//
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI 28 // PD3
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO 26 // PD1
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK 27 // PD2
#endif
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN 10 // D10 PB19 THERM AN1 *
#define TEMP_1_PIN 9 // D9 PB18 THERM AN2 *
#define TEMP_2_PIN 8 // D8 PB17 THERM AN4 *
#define TEMP_BED_PIN 11 // D11 PB20 THERM AN3 *
//
// Heaters / Fans
//
#define HEATER_0_PIN 6 // D6 PC24 FET_PWM3
#define HEATER_1_PIN 7 // D7 PC23 FET_PWM4
#define HEATER_2_PIN 8 // D8 PC22 FET_PWM5
#define HEATER_BED_PIN 9 // D9 PC21 BED_PWM
#ifndef FAN_PIN
#define FAN_PIN 4 // D4 PC26 FET_PWM1
#endif
#define FAN1_PIN 5 // D5 PC25 FET_PWM2
//
// Misc. Functions
//
// Internal MicroSD card reader on the PCB
#define INT_SCK_PIN 42 // D42 PA19/MCCK
#define INT_MISO_PIN 43 // D43 PA20/MCCDA
#define INT_MOSI_PIN 73 // D73 PA21/MCDA0
#define INT_SDSS 55 // D55 PA24/MCDA3
// External SD card reader on SC2
#define SD_SCK_PIN 76 // D76 PA27
#define SD_MISO_PIN 74 // D74 PA25
#define SD_MOSI_PIN 75 // D75 PA26
#define SDSS 87 // D87 PA29
// Unused Digital GPIO J20 Pins
#define GPIO_PB1_J20_5 94 // D94 PB1 (Header J20 5)
#define GPIO_PB0_J20_6 95 // D95 PB0 (Header J20 6)
#define GPIO_PB3_J20_7 103 // D103 PB3 (Header J20 7)
#define GPIO_PB2_J20_8 93 // D93 PB2 (Header J20 8)
#define GPIO_PB6_J20_9 99 // D99 PB6 (Header J20 9)
#define GPIO_PB5_J20_10 101 // D101 PB5 (Header J20 10)
#define GPIO_PB8_J20_11 100 // D100 PB8 (Header J20 11)
#define GPIO_PB4_J20_12 102 // D102 PB4 (Header J20 12)
#define GPIO_PB9_J20_13 108 // D108 PB9 (Header J20 13)
#define GPIO_PB7_J20_14 98 // D98 PB7 (Header J20 14)
#define GPIO_PB15_J20_15 66 // D66 PB15 (Header J20 15)
#define GPIO_PB16_J20_16 67 // D67 PB16 (Header J20 16)
#define GPIO_PB14_J20_17 53 // D53 PB14 (Header J20 17)
#define GPIO_PA18_J20_21 71 // D71 PA17 (Header J20 21)
#define GPIO_PA17_J20_22 70 // D70 PA17 (Header J20 22)
// Case Light
#ifndef CASE_LIGHT_PIN
#define CASE_LIGHT_PIN GPIO_PB1_J20_5
#endif
// 2MB SPI Flash
#define SPI_FLASH_SS 52 // D52 PB21
//
// Filament Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN GPIO_PB15_J20_15
#endif
#ifndef FIL_RUNOUT2_PIN
#define FIL_RUNOUT2_PIN GPIO_PB16_J20_16
#endif
//
// LCD / Controller
//
#if ANY(HAS_WIRED_LCD, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
#define BEEPER_PIN 23 // D24 PA15_CTS1
#define LCD_PINS_RS 17 // D17 PA12_RXD1
#define LCD_PINS_ENABLE 24 // D23 PA14_RTS1
#define LCD_PINS_D4 69 // D69 PA0_CANTX0
#define LCD_PINS_D5 54 // D54 PA16_SCK1
#define LCD_PINS_D6 68 // D68 PA1_CANRX0
#define LCD_PINS_D7 34 // D34 PC2_PWML0
#define SD_DETECT_PIN 2 // D2 PB25_TIOA0
#endif
#if ANY(IS_ULTIPANEL, TOUCH_UI_ULTIPANEL, TOUCH_UI_FTDI_EVE)
// Buttons on AUX-2
#define BTN_EN1 60 // D60 PA3_TIOB1
#define BTN_EN2 13 // D13 PB27_TIOB0
#define BTN_ENC 16 // D16 PA13_TXD1 // the click
#endif