You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
289 lines
7.9 KiB
289 lines
7.9 KiB
/*
|
|
wiring.c - Partial implementation of the Wiring API for the ATmega8.
|
|
Part of Arduino - http://www.arduino.cc/
|
|
|
|
Copyright (c) 2005-2006 David A. Mellis
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
Lesser General Public License for more details.
|
|
|
|
You should have received a copy of the GNU Lesser General
|
|
Public License along with this library; if not, write to the
|
|
Free Software Foundation, Inc., 59 Temple Place, Suite 330,
|
|
Boston, MA 02111-1307 USA
|
|
|
|
$Id$
|
|
*/
|
|
|
|
#include "wiring_private.h"
|
|
|
|
// the prescaler is set so that timer0 ticks every 64 clock cycles, and the
|
|
// the overflow handler is called every 256 ticks.
|
|
#define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(64 * 256))
|
|
|
|
// the whole number of milliseconds per timer0 overflow
|
|
#define MILLIS_INC (MICROSECONDS_PER_TIMER0_OVERFLOW / 1000)
|
|
|
|
// the fractional number of milliseconds per timer0 overflow. we shift right
|
|
// by three to fit these numbers into a byte. (for the clock speeds we care
|
|
// about - 8 and 16 MHz - this doesn't lose precision.)
|
|
#define FRACT_INC ((MICROSECONDS_PER_TIMER0_OVERFLOW % 1000) >> 3)
|
|
#define FRACT_MAX (1000 >> 3)
|
|
|
|
volatile unsigned long timer0_overflow_count = 0;
|
|
volatile unsigned long timer0_millis = 0;
|
|
static unsigned char timer0_fract = 0;
|
|
|
|
SIGNAL(TIMER0_OVF_vect)
|
|
{
|
|
// copy these to local variables so they can be stored in registers
|
|
// (volatile variables must be read from memory on every access)
|
|
unsigned long m = timer0_millis;
|
|
unsigned char f = timer0_fract;
|
|
|
|
m += MILLIS_INC;
|
|
f += FRACT_INC;
|
|
if (f >= FRACT_MAX) {
|
|
f -= FRACT_MAX;
|
|
m += 1;
|
|
}
|
|
|
|
timer0_fract = f;
|
|
timer0_millis = m;
|
|
timer0_overflow_count++;
|
|
}
|
|
|
|
unsigned long millis()
|
|
{
|
|
unsigned long m;
|
|
uint8_t oldSREG = SREG;
|
|
|
|
// disable interrupts while we read timer0_millis or we might get an
|
|
// inconsistent value (e.g. in the middle of a write to timer0_millis)
|
|
cli();
|
|
m = timer0_millis;
|
|
SREG = oldSREG;
|
|
|
|
return m;
|
|
}
|
|
|
|
unsigned long micros() {
|
|
unsigned long m;
|
|
uint8_t oldSREG = SREG, t;
|
|
|
|
cli();
|
|
m = timer0_overflow_count;
|
|
#if defined(TCNT0)
|
|
t = TCNT0;
|
|
#elif defined(TCNT0L)
|
|
t = TCNT0L;
|
|
#else
|
|
#error TIMER 0 not defined
|
|
#endif
|
|
|
|
|
|
#ifdef TIFR0
|
|
if ((TIFR0 & _BV(TOV0)) && (t < 255))
|
|
m++;
|
|
#else
|
|
if ((TIFR & _BV(TOV0)) && (t < 255))
|
|
m++;
|
|
#endif
|
|
|
|
SREG = oldSREG;
|
|
|
|
return ((m << 8) + t) * (64 / clockCyclesPerMicrosecond());
|
|
}
|
|
|
|
void delay(unsigned long ms)
|
|
{
|
|
uint16_t start = (uint16_t)micros();
|
|
|
|
while (ms > 0) {
|
|
if (((uint16_t)micros() - start) >= 1000) {
|
|
ms--;
|
|
start += 1000;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Delay for the given number of microseconds. Assumes a 8 or 16 MHz clock. */
|
|
void delayMicroseconds(unsigned int us)
|
|
{
|
|
// calling avrlib's delay_us() function with low values (e.g. 1 or
|
|
// 2 microseconds) gives delays longer than desired.
|
|
//delay_us(us);
|
|
|
|
#if F_CPU >= 16000000L
|
|
// for the 16 MHz clock on most Arduino boards
|
|
|
|
// for a one-microsecond delay, simply return. the overhead
|
|
// of the function call yields a delay of approximately 1 1/8 us.
|
|
if (--us == 0)
|
|
return;
|
|
|
|
// the following loop takes a quarter of a microsecond (4 cycles)
|
|
// per iteration, so execute it four times for each microsecond of
|
|
// delay requested.
|
|
us <<= 2;
|
|
|
|
// account for the time taken in the preceeding commands.
|
|
us -= 2;
|
|
#else
|
|
// for the 8 MHz internal clock on the ATmega168
|
|
|
|
// for a one- or two-microsecond delay, simply return. the overhead of
|
|
// the function calls takes more than two microseconds. can't just
|
|
// subtract two, since us is unsigned; we'd overflow.
|
|
if (--us == 0)
|
|
return;
|
|
if (--us == 0)
|
|
return;
|
|
|
|
// the following loop takes half of a microsecond (4 cycles)
|
|
// per iteration, so execute it twice for each microsecond of
|
|
// delay requested.
|
|
us <<= 1;
|
|
|
|
// partially compensate for the time taken by the preceeding commands.
|
|
// we can't subtract any more than this or we'd overflow w/ small delays.
|
|
us--;
|
|
#endif
|
|
|
|
// busy wait
|
|
__asm__ __volatile__ (
|
|
"1: sbiw %0,1" "\n\t" // 2 cycles
|
|
"brne 1b" : "=w" (us) : "0" (us) // 2 cycles
|
|
);
|
|
}
|
|
|
|
void init()
|
|
{
|
|
// this needs to be called before setup() or some functions won't
|
|
// work there
|
|
sei();
|
|
|
|
// on the ATmega168, timer 0 is also used for fast hardware pwm
|
|
// (using phase-correct PWM would mean that timer 0 overflowed half as often
|
|
// resulting in different millis() behavior on the ATmega8 and ATmega168)
|
|
#if defined(TCCR0A) && defined(WGM01)
|
|
sbi(TCCR0A, WGM01);
|
|
sbi(TCCR0A, WGM00);
|
|
#endif
|
|
|
|
// set timer 0 prescale factor to 64
|
|
#if defined(__AVR_ATmega128__)
|
|
// CPU specific: different values for the ATmega128
|
|
sbi(TCCR0, CS02);
|
|
#elif defined(TCCR0) && defined(CS01) && defined(CS00)
|
|
// this combination is for the standard atmega8
|
|
sbi(TCCR0, CS01);
|
|
sbi(TCCR0, CS00);
|
|
#elif defined(TCCR0B) && defined(CS01) && defined(CS00)
|
|
// this combination is for the standard 168/328/1280/2560
|
|
sbi(TCCR0B, CS01);
|
|
sbi(TCCR0B, CS00);
|
|
#elif defined(TCCR0A) && defined(CS01) && defined(CS00)
|
|
// this combination is for the __AVR_ATmega645__ series
|
|
sbi(TCCR0A, CS01);
|
|
sbi(TCCR0A, CS00);
|
|
#else
|
|
#error Timer 0 prescale factor 64 not set correctly
|
|
#endif
|
|
|
|
// enable timer 0 overflow interrupt
|
|
#if defined(TIMSK) && defined(TOIE0)
|
|
sbi(TIMSK, TOIE0);
|
|
#elif defined(TIMSK0) && defined(TOIE0)
|
|
sbi(TIMSK0, TOIE0);
|
|
#else
|
|
#error Timer 0 overflow interrupt not set correctly
|
|
#endif
|
|
|
|
// timers 1 and 2 are used for phase-correct hardware pwm
|
|
// this is better for motors as it ensures an even waveform
|
|
// note, however, that fast pwm mode can achieve a frequency of up
|
|
// 8 MHz (with a 16 MHz clock) at 50% duty cycle
|
|
|
|
TCCR1B = 0;
|
|
|
|
// set timer 1 prescale factor to 64
|
|
#if defined(TCCR1B) && defined(CS11) && defined(CS10)
|
|
sbi(TCCR1B, CS11);
|
|
sbi(TCCR1B, CS10);
|
|
#elif defined(TCCR1) && defined(CS11) && defined(CS10)
|
|
sbi(TCCR1, CS11);
|
|
sbi(TCCR1, CS10);
|
|
#endif
|
|
// put timer 1 in 8-bit phase correct pwm mode
|
|
#if defined(TCCR1A) && defined(WGM10)
|
|
sbi(TCCR1A, WGM10);
|
|
#elif defined(TCCR1)
|
|
#warning this needs to be finished
|
|
#endif
|
|
|
|
// set timer 2 prescale factor to 64
|
|
#if defined(TCCR2) && defined(CS22)
|
|
sbi(TCCR2, CS22);
|
|
#elif defined(TCCR2B) && defined(CS22)
|
|
sbi(TCCR2B, CS22);
|
|
#else
|
|
#warning Timer 2 not finished (may not be present on this CPU)
|
|
#endif
|
|
|
|
// configure timer 2 for phase correct pwm (8-bit)
|
|
#if defined(TCCR2) && defined(WGM20)
|
|
sbi(TCCR2, WGM20);
|
|
#elif defined(TCCR2A) && defined(WGM20)
|
|
sbi(TCCR2A, WGM20);
|
|
#else
|
|
#warning Timer 2 not finished (may not be present on this CPU)
|
|
#endif
|
|
|
|
#if defined(TCCR3B) && defined(CS31) && defined(WGM30)
|
|
sbi(TCCR3B, CS31); // set timer 3 prescale factor to 64
|
|
sbi(TCCR3B, CS30);
|
|
sbi(TCCR3A, WGM30); // put timer 3 in 8-bit phase correct pwm mode
|
|
#endif
|
|
|
|
#if defined(TCCR4B) && defined(CS41) && defined(WGM40)
|
|
sbi(TCCR4B, CS41); // set timer 4 prescale factor to 64
|
|
sbi(TCCR4B, CS40);
|
|
sbi(TCCR4A, WGM40); // put timer 4 in 8-bit phase correct pwm mode
|
|
#endif
|
|
|
|
#if defined(TCCR5B) && defined(CS51) && defined(WGM50)
|
|
sbi(TCCR5B, CS51); // set timer 5 prescale factor to 64
|
|
sbi(TCCR5B, CS50);
|
|
sbi(TCCR5A, WGM50); // put timer 5 in 8-bit phase correct pwm mode
|
|
#endif
|
|
|
|
#if defined(ADCSRA)
|
|
// set a2d prescale factor to 128
|
|
// 16 MHz / 128 = 125 KHz, inside the desired 50-200 KHz range.
|
|
// XXX: this will not work properly for other clock speeds, and
|
|
// this code should use F_CPU to determine the prescale factor.
|
|
sbi(ADCSRA, ADPS2);
|
|
sbi(ADCSRA, ADPS1);
|
|
sbi(ADCSRA, ADPS0);
|
|
|
|
// enable a2d conversions
|
|
sbi(ADCSRA, ADEN);
|
|
#endif
|
|
|
|
// the bootloader connects pins 0 and 1 to the USART; disconnect them
|
|
// here so they can be used as normal digital i/o; they will be
|
|
// reconnected in Serial.begin()
|
|
#if defined(UCSRB)
|
|
UCSRB = 0;
|
|
#elif defined(UCSR0B)
|
|
UCSR0B = 0;
|
|
#endif
|
|
}
|
|
|