Marlin_FB4S/Marlin/src/HAL/DUE/usb/sbc_protocol.h

/**
 * \file
 *
 * \brief SCSI Block Commands
 *
 * This file contains definitions of some of the commands found in the
 * SCSI SBC-2 standard.
 *
 * Note that the SBC specification depends on several commands defined
 * by the SCSI Primary Commands (SPC) standard. Each version of the SBC
 * standard is meant to be used in conjunction with a specific version
 * of the SPC standard, as follows:
 *   - SBC   depends on SPC
 *   - SBC-2 depends on SPC-3
 *   - SBC-3 depends on SPC-4
 *
 * Copyright (c) 2014-2015 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="https://www.atmel.com/design-support/">Atmel Support</a>
 */
#ifndef _SBC_PROTOCOL_H_
#define _SBC_PROTOCOL_H_


/**
 * \ingroup usb_msc_protocol
 * \defgroup usb_sbc_protocol SCSI Block Commands protocol definitions
 *
 * @{
 */

//! \name SCSI commands defined by SBC-2
//@{
#define  SBC_FORMAT_UNIT         0x04
#define  SBC_READ6               0x08
#define  SBC_WRITE6              0x0A
#define  SBC_START_STOP_UNIT     0x1B
#define  SBC_READ_CAPACITY10     0x25
#define  SBC_READ10              0x28
#define  SBC_WRITE10             0x2A
#define  SBC_VERIFY10            0x2F
//@}

//! \name SBC-2 Mode page definitions
//@{

enum scsi_sbc_mode {
	SCSI_MS_MODE_RW_ERR_RECOV = 0x01,	//!< Read-Write Error Recovery mode page
	SCSI_MS_MODE_FORMAT_DEVICE = 0x03,	//!< Format Device mode page
	SCSI_MS_MODE_FLEXIBLE_DISK = 0x05,	//!< Flexible Disk mode page
	SCSI_MS_MODE_CACHING = 0x08,	//!< Caching mode page
};


//! \name SBC-2 Device-Specific Parameter
//@{
#define SCSI_MS_SBC_WP              0x80	//!< Write Protected
#define SCSI_MS_SBC_DPOFUA          0x10	//!< DPO and FUA supported
//@}

/**
 * \brief SBC-2 Short LBA mode parameter block descriptor
 */
struct sbc_slba_block_desc {
	be32_t nr_blocks;	//!< Number of Blocks
	be32_t block_len;	//!< Block Length
#define SBC_SLBA_BLOCK_LEN_MASK   0x00FFFFFFU	//!< Mask reserved bits
};

/**
 * \brief SBC-2 Caching mode page
 */
struct sbc_caching_mode_page {
	uint8_t page_code;
	uint8_t page_length;
	uint8_t flags2;
#define  SBC_MP_CACHE_IC      (1 << 7)	//!< Initiator Control
#define  SBC_MP_CACHE_ABPF    (1 << 6)	//!< Abort Pre-Fetch
#define  SBC_MP_CACHE_CAP     (1 << 5)	//!< Catching Analysis Permitted
#define  SBC_MP_CACHE_DISC    (1 << 4)	//!< Discontinuity
#define  SBC_MP_CACHE_SIZE    (1 << 3)	//!< Size enable
#define  SBC_MP_CACHE_WCE     (1 << 2)	//!< Write back Cache Enable
#define  SBC_MP_CACHE_MF      (1 << 1)	//!< Multiplication Factor
#define  SBC_MP_CACHE_RCD     (1 << 0)	//!< Read Cache Disable
	uint8_t retention;
	be16_t dis_pf_transfer_len;
	be16_t min_prefetch;
	be16_t max_prefetch;
	be16_t max_prefetch_ceil;
	uint8_t flags12;
#define  SBC_MP_CACHE_FSW     (1 << 7)	//!< Force Sequential Write
#define  SBC_MP_CACHE_LBCSS   (1 << 6)	//!< Logical Blk Cache Seg Sz
#define  SBC_MP_CACHE_DRA     (1 << 5)	//!< Disable Read-Ahead
#define  SBC_MP_CACHE_NV_DIS  (1 << 0)	//!< Non-Volatile Cache Disable
	uint8_t nr_cache_segments;
	be16_t cache_segment_size;
	uint8_t reserved[4];
};

/**
 * \brief SBC-2 Read-Write Error Recovery mode page
 */
struct sbc_rdwr_error_recovery_mode_page {
	uint8_t page_code;
	uint8_t page_length;
#define  SPC_MP_RW_ERR_RECOV_PAGE_LENGTH    0x0A
	uint8_t flags1;
#define  SBC_MP_RW_ERR_RECOV_AWRE   (1 << 7)
#define  SBC_MP_RW_ERR_RECOV_ARRE   (1 << 6)
#define  SBC_MP_RW_ERR_RECOV_TB     (1 << 5)
#define  SBC_MP_RW_ERR_RECOV_RC     (1 << 4)
#define  SBC_MP_RW_ERR_RECOV_ERR    (1 << 3)
#define  SBC_MP_RW_ERR_RECOV_PER    (1 << 2)
#define  SBC_MP_RW_ERR_RECOV_DTE    (1 << 1)
#define  SBC_MP_RW_ERR_RECOV_DCR    (1 << 0)
	uint8_t read_retry_count;
	uint8_t correction_span;
	uint8_t head_offset_count;
	uint8_t data_strobe_offset_count;
	uint8_t flags2;
	uint8_t write_retry_count;
	uint8_t flags3;
	be16_t recovery_time_limit;
};
//@}

/**
 * \brief SBC-2 READ CAPACITY (10) parameter data
 */
struct sbc_read_capacity10_data {
	be32_t max_lba;	//!< LBA of last logical block
	be32_t block_len;	//!< Number of bytes in the last logical block
};

//@}

#endif // _SBC_PROTOCOL_H_