Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

432 lines
19 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
stepper_indirection.h - stepper motor driver indirection macros
to allow some stepper functions to be done via SPI/I2c instead of direct pin manipulation
Part of Marlin
Copyright (c) 2015 Dominik Wenger
Marlin is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Marlin is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Marlin. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef STEPPER_INDIRECTION_H
#define STEPPER_INDIRECTION_H
#include "MarlinConfig.h"
// TMC26X drivers have STEP/DIR on normal pins, but ENABLE via SPI
#if ENABLED(HAVE_TMCDRIVER)
#include <SPI.h>
#include <TMC26XStepper.h>
void tmc_init();
#endif
// TMC130 drivers have STEP/DIR/ENABLE on normal pins
#if ENABLED(HAVE_TMC2130DRIVER)
#include <SPI.h>
#include <Trinamic_TMC2130.h>
void tmc2130_init();
#endif
// L6470 has STEP on normal pins, but DIR/ENABLE via SPI
#if ENABLED(HAVE_L6470DRIVER)
#include <SPI.h>
#include <L6470.h>
void L6470_init();
#endif
// X Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(X_IS_L6470)
extern L6470 stepperX;
#define X_ENABLE_INIT NOOP
#define X_ENABLE_WRITE(STATE) do{if(STATE) stepperX.Step_Clock(stepperX.getStatus() & STATUS_HIZ); else stepperX.softFree();}while(0)
#define X_ENABLE_READ (stepperX.getStatus() & STATUS_HIZ)
#define X_DIR_INIT NOOP
#define X_DIR_WRITE(STATE) stepperX.Step_Clock(STATE)
#define X_DIR_READ (stepperX.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(X_IS_TMC)
extern TMC26XStepper stepperX;
#define X_ENABLE_INIT NOOP
#define X_ENABLE_WRITE(STATE) stepperX.setEnabled(STATE)
#define X_ENABLE_READ stepperX.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(X_IS_TMC2130)
extern Trinamic_TMC2130 stepperX;
#endif
#define X_ENABLE_INIT SET_OUTPUT(X_ENABLE_PIN)
#define X_ENABLE_WRITE(STATE) WRITE(X_ENABLE_PIN,STATE)
#define X_ENABLE_READ READ(X_ENABLE_PIN)
#endif
#define X_DIR_INIT SET_OUTPUT(X_DIR_PIN)
#define X_DIR_WRITE(STATE) WRITE(X_DIR_PIN,STATE)
#define X_DIR_READ READ(X_DIR_PIN)
#endif
#define X_STEP_INIT SET_OUTPUT(X_STEP_PIN)
#define X_STEP_WRITE(STATE) WRITE(X_STEP_PIN,STATE)
#define X_STEP_READ READ(X_STEP_PIN)
// Y Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(Y_IS_L6470)
extern L6470 stepperY;
#define Y_ENABLE_INIT NOOP
#define Y_ENABLE_WRITE(STATE) do{if(STATE) stepperY.Step_Clock(stepperY.getStatus() & STATUS_HIZ); else stepperY.softFree();}while(0)
#define Y_ENABLE_READ (stepperY.getStatus() & STATUS_HIZ)
#define Y_DIR_INIT NOOP
#define Y_DIR_WRITE(STATE) stepperY.Step_Clock(STATE)
#define Y_DIR_READ (stepperY.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(Y_IS_TMC)
extern TMC26XStepper stepperY;
#define Y_ENABLE_INIT NOOP
#define Y_ENABLE_WRITE(STATE) stepperY.setEnabled(STATE)
#define Y_ENABLE_READ stepperY.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Y_IS_TMC2130)
extern Trinamic_TMC2130 stepperY;
#endif
#define Y_ENABLE_INIT SET_OUTPUT(Y_ENABLE_PIN)
#define Y_ENABLE_WRITE(STATE) WRITE(Y_ENABLE_PIN,STATE)
#define Y_ENABLE_READ READ(Y_ENABLE_PIN)
#endif
#define Y_DIR_INIT SET_OUTPUT(Y_DIR_PIN)
#define Y_DIR_WRITE(STATE) WRITE(Y_DIR_PIN,STATE)
#define Y_DIR_READ READ(Y_DIR_PIN)
#endif
#define Y_STEP_INIT SET_OUTPUT(Y_STEP_PIN)
#define Y_STEP_WRITE(STATE) WRITE(Y_STEP_PIN,STATE)
#define Y_STEP_READ READ(Y_STEP_PIN)
// Z Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(Z_IS_L6470)
extern L6470 stepperZ;
#define Z_ENABLE_INIT NOOP
#define Z_ENABLE_WRITE(STATE) do{if(STATE) stepperZ.Step_Clock(stepperZ.getStatus() & STATUS_HIZ); else stepperZ.softFree();}while(0)
#define Z_ENABLE_READ (stepperZ.getStatus() & STATUS_HIZ)
#define Z_DIR_INIT NOOP
#define Z_DIR_WRITE(STATE) stepperZ.Step_Clock(STATE)
#define Z_DIR_READ (stepperZ.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(Z_IS_TMC)
extern TMC26XStepper stepperZ;
#define Z_ENABLE_INIT NOOP
#define Z_ENABLE_WRITE(STATE) stepperZ.setEnabled(STATE)
#define Z_ENABLE_READ stepperZ.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Z_IS_TMC2130)
extern Trinamic_TMC2130 stepperZ;
#endif
#define Z_ENABLE_INIT SET_OUTPUT(Z_ENABLE_PIN)
#define Z_ENABLE_WRITE(STATE) WRITE(Z_ENABLE_PIN,STATE)
#define Z_ENABLE_READ READ(Z_ENABLE_PIN)
#endif
#define Z_DIR_INIT SET_OUTPUT(Z_DIR_PIN)
#define Z_DIR_WRITE(STATE) WRITE(Z_DIR_PIN,STATE)
#define Z_DIR_READ READ(Z_DIR_PIN)
#endif
#define Z_STEP_INIT SET_OUTPUT(Z_STEP_PIN)
#define Z_STEP_WRITE(STATE) WRITE(Z_STEP_PIN,STATE)
#define Z_STEP_READ READ(Z_STEP_PIN)
// X2 Stepper
#if HAS_X2_ENABLE
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(X2_IS_L6470)
extern L6470 stepperX2;
#define X2_ENABLE_INIT NOOP
#define X2_ENABLE_WRITE(STATE) do{if(STATE) stepperX2.Step_Clock(stepperX2.getStatus() & STATUS_HIZ); else stepperX2.softFree();}while(0)
#define X2_ENABLE_READ (stepperX2.getStatus() & STATUS_HIZ)
#define X2_DIR_INIT NOOP
#define X2_DIR_WRITE(STATE) stepperX2.Step_Clock(STATE)
#define X2_DIR_READ (stepperX2.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(X2_IS_TMC)
extern TMC26XStepper stepperX2;
#define X2_ENABLE_INIT NOOP
#define X2_ENABLE_WRITE(STATE) stepperX2.setEnabled(STATE)
#define X2_ENABLE_READ stepperX2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(X2_IS_TMC2130)
extern Trinamic_TMC2130 stepperX2;
#endif
#define X2_ENABLE_INIT SET_OUTPUT(X2_ENABLE_PIN)
#define X2_ENABLE_WRITE(STATE) WRITE(X2_ENABLE_PIN,STATE)
#define X2_ENABLE_READ READ(X2_ENABLE_PIN)
#endif
#define X2_DIR_INIT SET_OUTPUT(X2_DIR_PIN)
#define X2_DIR_WRITE(STATE) WRITE(X2_DIR_PIN,STATE)
#define X2_DIR_READ READ(X2_DIR_PIN)
#endif
#define X2_STEP_INIT SET_OUTPUT(X2_STEP_PIN)
#define X2_STEP_WRITE(STATE) WRITE(X2_STEP_PIN,STATE)
#define X2_STEP_READ READ(X2_STEP_PIN)
#endif
// Y2 Stepper
#if HAS_Y2_ENABLE
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(Y2_IS_L6470)
extern L6470 stepperY2;
#define Y2_ENABLE_INIT NOOP
#define Y2_ENABLE_WRITE(STATE) do{if(STATE) stepperY2.Step_Clock(stepperY2.getStatus() & STATUS_HIZ); else stepperY2.softFree();}while(0)
#define Y2_ENABLE_READ (stepperY2.getStatus() & STATUS_HIZ)
#define Y2_DIR_INIT NOOP
#define Y2_DIR_WRITE(STATE) stepperY2.Step_Clock(STATE)
#define Y2_DIR_READ (stepperY2.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(Y2_IS_TMC)
extern TMC26XStepper stepperY2;
#define Y2_ENABLE_INIT NOOP
#define Y2_ENABLE_WRITE(STATE) stepperY2.setEnabled(STATE)
#define Y2_ENABLE_READ stepperY2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Y2_IS_TMC2130)
extern Trinamic_TMC2130 stepperY2;
#endif
#define Y2_ENABLE_INIT SET_OUTPUT(Y2_ENABLE_PIN)
#define Y2_ENABLE_WRITE(STATE) WRITE(Y2_ENABLE_PIN,STATE)
#define Y2_ENABLE_READ READ(Y2_ENABLE_PIN)
#endif
#define Y2_DIR_INIT SET_OUTPUT(Y2_DIR_PIN)
#define Y2_DIR_WRITE(STATE) WRITE(Y2_DIR_PIN,STATE)
#define Y2_DIR_READ READ(Y2_DIR_PIN)
#endif
#define Y2_STEP_INIT SET_OUTPUT(Y2_STEP_PIN)
#define Y2_STEP_WRITE(STATE) WRITE(Y2_STEP_PIN,STATE)
#define Y2_STEP_READ READ(Y2_STEP_PIN)
#endif
// Z2 Stepper
#if HAS_Z2_ENABLE
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(Z2_IS_L6470)
extern L6470 stepperZ2;
#define Z2_ENABLE_INIT NOOP
#define Z2_ENABLE_WRITE(STATE) do{if(STATE) stepperZ2.Step_Clock(stepperZ2.getStatus() & STATUS_HIZ); else stepperZ2.softFree();}while(0)
#define Z2_ENABLE_READ (stepperZ2.getStatus() & STATUS_HIZ)
#define Z2_DIR_INIT NOOP
#define Z2_DIR_WRITE(STATE) stepperZ2.Step_Clock(STATE)
#define Z2_DIR_READ (stepperZ2.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(Z2_IS_TMC)
extern TMC26XStepper stepperZ2;
#define Z2_ENABLE_INIT NOOP
#define Z2_ENABLE_WRITE(STATE) stepperZ2.setEnabled(STATE)
#define Z2_ENABLE_READ stepperZ2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(Z2_IS_TMC2130)
extern Trinamic_TMC2130 stepperZ2;
#endif
#define Z2_ENABLE_INIT SET_OUTPUT(Z2_ENABLE_PIN)
#define Z2_ENABLE_WRITE(STATE) WRITE(Z2_ENABLE_PIN,STATE)
#define Z2_ENABLE_READ READ(Z2_ENABLE_PIN)
#endif
#define Z2_DIR_INIT SET_OUTPUT(Z2_DIR_PIN)
#define Z2_DIR_WRITE(STATE) WRITE(Z2_DIR_PIN,STATE)
#define Z2_DIR_READ READ(Z2_DIR_PIN)
#endif
#define Z2_STEP_INIT SET_OUTPUT(Z2_STEP_PIN)
#define Z2_STEP_WRITE(STATE) WRITE(Z2_STEP_PIN,STATE)
#define Z2_STEP_READ READ(Z2_STEP_PIN)
#endif
// E0 Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(E0_IS_L6470)
extern L6470 stepperE0;
#define E0_ENABLE_INIT NOOP
#define E0_ENABLE_WRITE(STATE) do{if(STATE) stepperE0.Step_Clock(stepperE0.getStatus() & STATUS_HIZ); else stepperE0.softFree();}while(0)
#define E0_ENABLE_READ (stepperE0.getStatus() & STATUS_HIZ)
#define E0_DIR_INIT NOOP
#define E0_DIR_WRITE(STATE) stepperE0.Step_Clock(STATE)
#define E0_DIR_READ (stepperE0.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(E0_IS_TMC)
extern TMC26XStepper stepperE0;
#define E0_ENABLE_INIT NOOP
#define E0_ENABLE_WRITE(STATE) stepperE0.setEnabled(STATE)
#define E0_ENABLE_READ stepperE0.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E0_IS_TMC2130)
extern Trinamic_TMC2130 stepperE0;
#endif
#define E0_ENABLE_INIT SET_OUTPUT(E0_ENABLE_PIN)
#define E0_ENABLE_WRITE(STATE) WRITE(E0_ENABLE_PIN,STATE)
#define E0_ENABLE_READ READ(E0_ENABLE_PIN)
#endif
#define E0_DIR_INIT SET_OUTPUT(E0_DIR_PIN)
#define E0_DIR_WRITE(STATE) WRITE(E0_DIR_PIN,STATE)
#define E0_DIR_READ READ(E0_DIR_PIN)
#endif
#define E0_STEP_INIT SET_OUTPUT(E0_STEP_PIN)
#define E0_STEP_WRITE(STATE) WRITE(E0_STEP_PIN,STATE)
#define E0_STEP_READ READ(E0_STEP_PIN)
// E1 Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(E1_IS_L6470)
extern L6470 stepperE1;
#define E1_ENABLE_INIT NOOP
#define E1_ENABLE_WRITE(STATE) do{if(STATE) stepperE1.Step_Clock(stepperE1.getStatus() & STATUS_HIZ); else stepperE1.softFree();}while(0)
#define E1_ENABLE_READ (stepperE1.getStatus() & STATUS_HIZ)
#define E1_DIR_INIT NOOP
#define E1_DIR_WRITE(STATE) stepperE1.Step_Clock(STATE)
#define E1_DIR_READ (stepperE1.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(E1_IS_TMC)
extern TMC26XStepper stepperE1;
#define E1_ENABLE_INIT NOOP
#define E1_ENABLE_WRITE(STATE) stepperE1.setEnabled(STATE)
#define E1_ENABLE_READ stepperE1.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E1_IS_TMC2130)
extern Trinamic_TMC2130 stepperE1;
#endif
#define E1_ENABLE_INIT SET_OUTPUT(E1_ENABLE_PIN)
#define E1_ENABLE_WRITE(STATE) WRITE(E1_ENABLE_PIN,STATE)
#define E1_ENABLE_READ READ(E1_ENABLE_PIN)
#endif
#define E1_DIR_INIT SET_OUTPUT(E1_DIR_PIN)
#define E1_DIR_WRITE(STATE) WRITE(E1_DIR_PIN,STATE)
#define E1_DIR_READ READ(E1_DIR_PIN)
#endif
#define E1_STEP_INIT SET_OUTPUT(E1_STEP_PIN)
#define E1_STEP_WRITE(STATE) WRITE(E1_STEP_PIN,STATE)
#define E1_STEP_READ READ(E1_STEP_PIN)
// E2 Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(E2_IS_L6470)
extern L6470 stepperE2;
#define E2_ENABLE_INIT NOOP
#define E2_ENABLE_WRITE(STATE) do{if(STATE) stepperE2.Step_Clock(stepperE2.getStatus() & STATUS_HIZ); else stepperE2.softFree();}while(0)
#define E2_ENABLE_READ (stepperE2.getStatus() & STATUS_HIZ)
#define E2_DIR_INIT NOOP
#define E2_DIR_WRITE(STATE) stepperE2.Step_Clock(STATE)
#define E2_DIR_READ (stepperE2.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(E2_IS_TMC)
extern TMC26XStepper stepperE2;
#define E2_ENABLE_INIT NOOP
#define E2_ENABLE_WRITE(STATE) stepperE2.setEnabled(STATE)
#define E2_ENABLE_READ stepperE2.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E2_IS_TMC2130)
extern Trinamic_TMC2130 stepperE2;
#endif
#define E2_ENABLE_INIT SET_OUTPUT(E2_ENABLE_PIN)
#define E2_ENABLE_WRITE(STATE) WRITE(E2_ENABLE_PIN,STATE)
#define E2_ENABLE_READ READ(E2_ENABLE_PIN)
#endif
#define E2_DIR_INIT SET_OUTPUT(E2_DIR_PIN)
#define E2_DIR_WRITE(STATE) WRITE(E2_DIR_PIN,STATE)
#define E2_DIR_READ READ(E2_DIR_PIN)
#endif
#define E2_STEP_INIT SET_OUTPUT(E2_STEP_PIN)
#define E2_STEP_WRITE(STATE) WRITE(E2_STEP_PIN,STATE)
#define E2_STEP_READ READ(E2_STEP_PIN)
// E3 Stepper
#if ENABLED(HAVE_L6470DRIVER) && ENABLED(E3_IS_L6470)
extern L6470 stepperE3;
#define E3_ENABLE_INIT NOOP
#define E3_ENABLE_WRITE(STATE) do{if(STATE) stepperE3.Step_Clock(stepperE3.getStatus() & STATUS_HIZ); else stepperE3.softFree();}while(0)
#define E3_ENABLE_READ (stepperE3.getStatus() & STATUS_HIZ)
#define E3_DIR_INIT NOOP
#define E3_DIR_WRITE(STATE) stepperE3.Step_Clock(STATE)
#define E3_DIR_READ (stepperE3.getStatus() & STATUS_DIR)
#else
#if ENABLED(HAVE_TMCDRIVER) && ENABLED(E3_IS_TMC)
extern TMC26XStepper stepperE3;
#define E3_ENABLE_INIT NOOP
#define E3_ENABLE_WRITE(STATE) stepperE3.setEnabled(STATE)
#define E3_ENABLE_READ stepperE3.isEnabled()
#else
#if ENABLED(HAVE_TMC2130DRIVER) && ENABLED(E3_IS_TMC2130)
extern Trinamic_TMC2130 stepperE3;
#endif
#define E3_ENABLE_INIT SET_OUTPUT(E3_ENABLE_PIN)
#define E3_ENABLE_WRITE(STATE) WRITE(E3_ENABLE_PIN,STATE)
#define E3_ENABLE_READ READ(E3_ENABLE_PIN)
#endif
#define E3_DIR_INIT SET_OUTPUT(E3_DIR_PIN)
#define E3_DIR_WRITE(STATE) WRITE(E3_DIR_PIN,STATE)
#define E3_DIR_READ READ(E3_DIR_PIN)
#endif
#define E3_STEP_INIT SET_OUTPUT(E3_STEP_PIN)
#define E3_STEP_WRITE(STATE) WRITE(E3_STEP_PIN,STATE)
#define E3_STEP_READ READ(E3_STEP_PIN)
/**
* Extruder indirection for the single E axis
*/
#if ENABLED(SWITCHING_EXTRUDER)
#define E_STEP_WRITE(v) E0_STEP_WRITE(v)
#define NORM_E_DIR() E0_DIR_WRITE(current_block->active_extruder ? INVERT_E0_DIR : !INVERT_E0_DIR)
#define REV_E_DIR() E0_DIR_WRITE(current_block->active_extruder ? !INVERT_E0_DIR : INVERT_E0_DIR)
#elif EXTRUDERS > 3
#define E_STEP_WRITE(v) { switch (current_block->active_extruder) { case 0: E0_STEP_WRITE(v); break; case 1: E1_STEP_WRITE(v); break; case 2: E2_STEP_WRITE(v); break; case 3: E3_STEP_WRITE(v); } }
#define NORM_E_DIR() { switch (current_block->active_extruder) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); } }
#define REV_E_DIR() { switch (current_block->active_extruder) { case 0: E0_DIR_WRITE(INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(INVERT_E3_DIR); } }
#elif EXTRUDERS > 2
#define E_STEP_WRITE(v) { switch (current_block->active_extruder) { case 0: E0_STEP_WRITE(v); break; case 1: E1_STEP_WRITE(v); break; case 2: E2_STEP_WRITE(v); } }
#define NORM_E_DIR() { switch (current_block->active_extruder) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); } }
#define REV_E_DIR() { switch (current_block->active_extruder) { case 0: E0_DIR_WRITE(INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(INVERT_E2_DIR); } }
#elif EXTRUDERS > 1
#if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
#define E_STEP_WRITE(v) { if (extruder_duplication_enabled) { E0_STEP_WRITE(v); E1_STEP_WRITE(v); } else if (current_block->active_extruder == 0) { E0_STEP_WRITE(v); } else { E1_STEP_WRITE(v); } }
#define NORM_E_DIR() { if (extruder_duplication_enabled) { E0_DIR_WRITE(!INVERT_E0_DIR); E1_DIR_WRITE(!INVERT_E1_DIR); } else if (current_block->active_extruder == 0) { E0_DIR_WRITE(!INVERT_E0_DIR); } else { E1_DIR_WRITE(!INVERT_E1_DIR); } }
#define REV_E_DIR() { if (extruder_duplication_enabled) { E0_DIR_WRITE(INVERT_E0_DIR); E1_DIR_WRITE(INVERT_E1_DIR); } else if (current_block->active_extruder == 0) { E0_DIR_WRITE(INVERT_E0_DIR); } else { E1_DIR_WRITE(INVERT_E1_DIR); } }
#else
#define E_STEP_WRITE(v) { if (current_block->active_extruder == 0) { E0_STEP_WRITE(v); } else { E1_STEP_WRITE(v); } }
#define NORM_E_DIR() { if (current_block->active_extruder == 0) { E0_DIR_WRITE(!INVERT_E0_DIR); } else { E1_DIR_WRITE(!INVERT_E1_DIR); } }
#define REV_E_DIR() { if (current_block->active_extruder == 0) { E0_DIR_WRITE(INVERT_E0_DIR); } else { E1_DIR_WRITE(INVERT_E1_DIR); } }
#endif
#elif ENABLED(MIXING_EXTRUDER)
#define E_STEP_WRITE(v) NOOP /* not used for mixing extruders! */
#if MIXING_STEPPERS > 3
#define En_STEP_WRITE(n,v) { switch (n) { case 0: E0_STEP_WRITE(v); break; case 1: E1_STEP_WRITE(v); break; case 2: E2_STEP_WRITE(v); break; case 3: E3_STEP_WRITE(v); } }
#define NORM_E_DIR() { E0_DIR_WRITE(!INVERT_E0_DIR); E1_DIR_WRITE(!INVERT_E1_DIR); E2_DIR_WRITE(!INVERT_E2_DIR); E3_DIR_WRITE(!INVERT_E3_DIR); }
#define REV_E_DIR() { E0_DIR_WRITE( INVERT_E0_DIR); E1_DIR_WRITE( INVERT_E1_DIR); E2_DIR_WRITE( INVERT_E2_DIR); E3_DIR_WRITE( INVERT_E3_DIR); }
#elif MIXING_STEPPERS > 2
#define En_STEP_WRITE(n,v) { switch (n) { case 0: E0_STEP_WRITE(v); break; case 1: E1_STEP_WRITE(v); break; case 2: E2_STEP_WRITE(v); } }
#define NORM_E_DIR() { E0_DIR_WRITE(!INVERT_E0_DIR); E1_DIR_WRITE(!INVERT_E1_DIR); E2_DIR_WRITE(!INVERT_E2_DIR); }
#define REV_E_DIR() { E0_DIR_WRITE( INVERT_E0_DIR); E1_DIR_WRITE( INVERT_E1_DIR); E2_DIR_WRITE( INVERT_E2_DIR); }
#else
#define En_STEP_WRITE(n,v) { switch (n) { case 0: E0_STEP_WRITE(v); break; case 1: E1_STEP_WRITE(v); } }
#define NORM_E_DIR() { E0_DIR_WRITE(!INVERT_E0_DIR); E1_DIR_WRITE(!INVERT_E1_DIR); }
#define REV_E_DIR() { E0_DIR_WRITE( INVERT_E0_DIR); E1_DIR_WRITE( INVERT_E1_DIR); }
#endif
#else
#define E_STEP_WRITE(v) E0_STEP_WRITE(v)
#define NORM_E_DIR() E0_DIR_WRITE(!INVERT_E0_DIR)
#define REV_E_DIR() E0_DIR_WRITE(INVERT_E0_DIR)
#endif
#endif // STEPPER_INDIRECTION_H