Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

129 lines
3.2 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* MegaTronics v3.0 pin assignments
*/
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Megatronics v3.0"
#define LARGE_FLASH true
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
// Servo support
#define SERVO0_PIN 46 //AUX3-6
#define SERVO1_PIN 47 //AUX3-5
#define SERVO2_PIN 48 //AUX3-4
#define SERVO3_PIN 49 //AUX3-3
#define X_STEP_PIN 58
#define X_DIR_PIN 57
#define X_ENABLE_PIN 59
#define X_MIN_PIN 37
#define X_MAX_PIN 40 // put to -1 to disable
#define Y_STEP_PIN 5
#define Y_DIR_PIN 17
#define Y_ENABLE_PIN 4
#define Y_MIN_PIN 41
#define Y_MAX_PIN 38 // put to -1 to disable
#define Z_STEP_PIN 16
#define Z_DIR_PIN 11
#define Z_ENABLE_PIN 3
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19 // put to -1 to disable
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 29
#define E1_STEP_PIN 25
#define E1_DIR_PIN 24
#define E1_ENABLE_PIN 26
#define E2_STEP_PIN 22
#define E2_DIR_PIN 60
#define E2_ENABLE_PIN 23
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN 12
#define HEATER_0_PIN 2
#define HEATER_1_PIN 9
#define HEATER_2_PIN 8
#define HEATER_BED_PIN 10
#define FAN_PIN 6
#define FAN2_PIN 7
#if TEMP_SENSOR_0 == -1
#define TEMP_0_PIN 11 // ANALOG NUMBERING
#else
#define TEMP_0_PIN 15 // ANALOG NUMBERING
#endif
#if TEMP_SENSOR_1 == -1
#define TEMP_1_PIN 10 // ANALOG NUMBERING
#else
#define TEMP_1_PIN 13 // ANALOG NUMBERING
#endif
#if TEMP_SENSOR_2 == -1
#define TEMP_2_PIN 9 // ANALOG NUMBERING
#else
#define TEMP_2_PIN 12 // ANALOG NUMBERING
#endif
#if TEMP_SENSOR_BED == -1
#define TEMP_BED_PIN 8 // ANALOG NUMBERING
#else
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#endif
#define BEEPER_PIN 61
#define LCD_PINS_RS 32
#define LCD_PINS_ENABLE 31
#define LCD_PINS_D4 14
#define LCD_PINS_D5 30
#define LCD_PINS_D6 39
#define LCD_PINS_D7 15
#define SHIFT_CLK 43
#define SHIFT_LD 35
#define SHIFT_OUT 34
#define SHIFT_EN 44
// Buttons are directly attached using keypad
#define BTN_EN1 44
#define BTN_EN2 45
#define BTN_ENC 33 // the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0