Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

116 lines
3.4 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* AZTEEG_X3_PRO (Arduino Mega) pin assignments
*/
#define BOARD_NAME "Azteeg X3 Pro"
#include "pins_RAMPS_14.h"
#undef FAN_PIN
#define FAN_PIN 6 //Part Cooling System
#undef BEEPER_PIN
#define BEEPER_PIN 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5
#define EXTRUDER_1_AUTO_FAN_PIN 5
#define EXTRUDER_2_AUTO_FAN_PIN 5
#define EXTRUDER_3_AUTO_FAN_PIN 5
//
//This section is to swap the MIN and MAX pins because the X3 Pro comes with only
//MIN endstops soldered onto the board. Delta code wants the homing endstops to be
//the MAX so I swapped them here.
//
#if ENABLED(DELTA)
#undef X_MIN_PIN
#undef X_MAX_PIN
#undef Y_MIN_PIN
#undef Y_MAX_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
#define X_MIN_PIN 2
#define X_MAX_PIN 3
#define Y_MIN_PIN 15
#define Y_MAX_PIN 14
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
#endif
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
//#undef Z_MIN_PIN
//#define Z_MIN_PIN 15
// Define a pin to use as the signal pin on Arduino for the Z probe endstop.
#define Z_MIN_PROBE_PIN 19
#endif
//
#define E2_STEP_PIN 23
#define E2_DIR_PIN 25
#define E2_ENABLE_PIN 40
#define E3_STEP_PIN 27
#define E3_DIR_PIN 29
#define E3_ENABLE_PIN 41
#define E4_STEP_PIN 43
#define E4_DIR_PIN 37
#define E4_ENABLE_PIN 42
#undef HEATER_1_PIN
#undef HEATER_2_PIN
#undef HEATER_3_PIN
#define HEATER_1_PIN 9
#define HEATER_2_PIN 16
#define HEATER_3_PIN 17
#define HEATER_4_PIN 4
#define HEATER_5_PIN 5
#define HEATER_6_PIN 6
#define HEATER_7_PIN 11
#undef TEMP_2_PIN
#undef TEMP_3_PIN
#define TEMP_2_PIN 12 // ANALOG NUMBERING
#define TEMP_3_PIN 11 // ANALOG NUMBERING
#define TEMP_4_PIN 10 // ANALOG NUMBERING
#define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
#define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
//
// These Servo pins are for when they are defined. Tested for usage with bed leveling
// on a Delta with 1 servo. Running through the Z servo endstop in code.
// Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins.
//
#undef SERVO0_PIN
#define SERVO0_PIN 47
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 49 // For easy adapter board
#elif ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 32
#define STAT_LED_BLUE 35
#endif