Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

139 lines
3.8 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/************************************************
* Rambo pin assignments MODIFIED FOR A4JP
************************************************/
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
#endif
// Servo support
#define SERVO0_PIN 22 // Motor header MX1
#define SERVO1_PIN 23 // Motor header MX2
#define SERVO2_PIN 24 // Motor header MX3
#define SERVO3_PIN 5 // PWM header pin 5
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
//Fan_2 2
/*****************
#if ENABLED(ULTRA_LCD)
#define KILL_PIN -1 //was 80 Glen maybe a mistake
#endif // ULTRA_LCD */
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER_PIN 44
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 70
#define DOGLCD_CS 71
#define LCD_SCREEN_ROT_180
#define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 22
#define STAT_LED_BLUE 32
#endif
#endif // VIKI2/miniVIKI
#define FILWIDTH_PIN 3 // ANALOG NUMBERING
/************************************************
* Rambo pin assignments old
************************************************/
#define LARGE_FLASH true
#define X_STEP_PIN 37
#define X_DIR_PIN 48
#define X_MIN_PIN 12
#define X_MAX_PIN 24
#define X_ENABLE_PIN 29
#define X_MS1_PIN 40
#define X_MS2_PIN 41
#define Y_STEP_PIN 36
#define Y_DIR_PIN 49
#define Y_MIN_PIN 11
#define Y_MAX_PIN 23
#define Y_ENABLE_PIN 28
#define Y_MS1_PIN 69
#define Y_MS2_PIN 39
#define Z_STEP_PIN 35
#define Z_DIR_PIN 47
#define Z_MIN_PIN 10
#define Z_MAX_PIN 30
#define Z_ENABLE_PIN 27
#define Z_MS1_PIN 68
#define Z_MS2_PIN 67
#define HEATER_BED_PIN 3
#define TEMP_BED_PIN 7 //2014/02/04 0:T0 / 1:T1 / 2:T2 / 7:T3
#define HEATER_0_PIN 9
#define TEMP_0_PIN 0
#define HEATER_1_PIN 7
#define E0_STEP_PIN 34
#define E0_DIR_PIN 43
#define E0_ENABLE_PIN 26
#define E0_MS1_PIN 65
#define E0_MS2_PIN 66
#define E1_STEP_PIN 33
#define E1_DIR_PIN 42
#define E1_ENABLE_PIN 25
#define E1_MS1_PIN 63
#define E1_MS2_PIN 64
#define DIGIPOTSS_PIN 38
#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping
#define SDSS 53
#define LED_PIN 13
#define FAN_PIN 8
#define PS_ON_PIN 4
#define FAN_0_PIN 6 //Glen
#define FAN_1_PIN 2 //Glen
// 2015/12/23
#define LCD_PINS_RS 70 //ext2_5
#define LCD_PINS_ENABLE 71 //ext2_7
#define LCD_PINS_D4 72 ///////Ext2 9 ?
#define LCD_PINS_D5 73 ///////Ext2 11 ?
#define LCD_PINS_D6 74 //ext2_13
#define LCD_PINS_D7 75 ///////Ext2 15 ?
#define BEEPER_PIN -1
#define BTN_HOME 80 //ext_16
#define BTN_CENTER 81 //ext_14
#define BTN_ENC BTN_CENTER
#define BTN_RIGHT 82 //ext_12
#define BTN_LEFT 83 //ext_10
#define BTN_UP 84 //ext2_8
#define BTN_DOWN 85 //ext2_6
#define HOME_PIN BTN_HOME