Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
InsanityAutomation 6a312fae80 Add before/after dir change delays (#15314) 5 years ago
..
Configuration.h Configurable TOUCH_BUTTONS repeat delays (#15245) 5 years ago
Configuration_adv.h Add before/after dir change delays (#15314) 5 years ago
README.md whitespace 5 years ago

README.md

Malyan M200 Build Instructions

Malyan M200 series firmware currently builds using the Arduino IDE. These instructions should guide you through the configuration and compilation.

  1. Install the Arduino IDE from your favorite source (arduino.cc, windows store, app store)
  2. Launch the IDE to add the ST boards manager:
  3. Select Tools > Board > Boards Manager.
  4. Type "Malyan" into the Search field.
  5. The only board listed will be "STM32 Cores by STMicroelectronics." Any version from 1.6.0 up is fine. Choose install. This will download many tools and packages, be patient.
  6. Open the Tools > Board submenu, scroll all the way down, and select 3D Printer Boards.
  7. From the Tools menu, select a board part number:
    • If you own a M200 V1 or early run (black V2), choose Malyan M200 V1.
    • If you own a M200 V2 later run (white/black) or V3 (Pro), choose Malyan M200 V2 (The V2 and V3 both share an STM32F070 MCU). Note that the V3 pinout is not complete (autolevel doesn't work as of this writing).
  8. From the Tools menu, choose USB Support > CDC No Generic Serial.
  9. Download the latest Marlin source (from the bugfix-2.0.x branch) and unzip it.
  10. Look in the Marlin subdirectory for the Configuration.h and Configuration_adv.h files. Replace these files with the configurations in the config\examples\Malyan\M200 folder.
  11. If you have an early-run V2, the steps-per-mm are roughly half. Consult the mpminipro.com wiki for the steps that apply to your unit. Modify Configuration.h.
  12. Inverting Axis. There's no pattern to axes will need to be inverted. The only way to know is to test your particular printer. If you do know, go ahead and invert the correct axes.
  13. Open the Marlin/Marlin.ino file in Arduino IDE.
  14. From the Sketch menu, select File > Export Compiled Binary.
  15. When compilation is done you've built the firmware. The next stage is to flash it to the board. To do this look for a line like this: "path/to/bin/arm-none-eabi-objcopy" -O binary "/path/to/Marlin.ino.elf" "/path/to/Marlin.ino.bin" The file Marlin.ino.bin is your firmware binary. M200 (v1-3) and M300 printers require flashing via SD card. Use the SD card that came with the printer if possible. The bootloader is very picky about SD cards. Copy Marlin.ino.bin to your SD card under three names: firmware.bin, update.bin, and fcupdate.flg.
  16. Insert the SD card into your printer. Make sure the X and Y axes are centered in the middle of the bed. (When X and Y endstops are closed this signals a UI upgrade to the bootloader.)
  17. Power-cycle the printer. The first flash may take longer. Don't be surprised if the .99 version number doesn't show up until after the UI has launched the default screen.
  18. Remove the SD card and delete the fcupdate.flg file from the card to prevent an accidental re-flash.
  19. Test the endstops and homing directions, run M303 PID autotune, and verify all features are working correctly.

Welcome to Marlin 2.x...