Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 

107 lines
3.8 KiB

// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
// Licence: GPL
#include <WProgram.h>
#include "fastio.h"
extern "C" void __cxa_pure_virtual();
void __cxa_pure_virtual(){};
void get_command();
void process_commands();
void manage_inactivity(byte debug);
void manage_heater();
int temp2analogu(int celsius, const short table[][2], int numtemps);
float analog2tempu(int raw, const short table[][2], int numtemps);
#ifdef HEATER_USES_THERMISTOR
#define HEATERSOURCE 1
#endif
#ifdef BED_USES_THERMISTOR
#define BEDSOURCE 1
#endif
#define temp2analogh( c ) temp2analogu((c),temptable,NUMTEMPS)
#define analog2temp( c ) analog2tempu((c),temptable,NUMTEMPS)
#if X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
#define enable_x() ;
#define disable_x() ;
#endif
#if Y_ENABLE_PIN > -1
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#else
#define enable_y() ;
#define disable_y() ;
#endif
#if Z_ENABLE_PIN > -1
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#else
#define enable_z() ;
#define disable_z() ;
#endif
#if E_ENABLE_PIN > -1
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e() ;
#define disable_e() ;
#endif
#define X_AXIS 0
#define Y_AXIS 1
#define Z_AXIS 2
#define E_AXIS 3
void FlushSerialRequestResend();
void ClearToSend();
void get_coordinates();
void prepare_move();
void linear_move(unsigned long steps_remaining[]);
void do_step(int axis);
void kill(byte debug);
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
// the source g-code and may never actually be reached if acceleration management is active.
typedef struct {
// Fields used by the bresenham algorithm for tracing the line
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
long step_event_count; // The number of step events required to complete this block
volatile long accelerate_until; // The index of the step event on which to stop acceleration
volatile long decelerate_after; // The index of the step event on which to start decelerating
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
long advance_rate;
volatile long initial_advance;
volatile long final_advance;
float advance;
// Fields used by the motion planner to manage acceleration
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
float nominal_speed; // The nominal speed for this block in mm/min
float millimeters; // The total travel of this block in mm
float entry_speed;
float acceleration; // acceleration mm/sec^2
// Settings for the trapezoid generator
long nominal_rate; // The nominal step rate for this block in step_events/sec
volatile long initial_rate; // The jerk-adjusted step rate at start of block
volatile long final_rate; // The minimal rate at exit
long acceleration_st; // acceleration steps/sec^2
volatile char busy;
} block_t;
void check_axes_activity();
void plan_init();
void st_init();
void tp_init();
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
void plan_set_position(float x, float y, float z, float e);
void st_wake_up();
void st_synchronize();