You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
449 lines
15 KiB
449 lines
15 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* BigTreeTech SKR 1.3 pin assignments
|
|
*/
|
|
|
|
#define BOARD_INFO_NAME "BTT SKR V1.3"
|
|
|
|
#define LPC1768_IS_SKRV1_3
|
|
#define USES_DIAG_JUMPERS
|
|
|
|
//
|
|
// Trinamic Stallguard pins
|
|
//
|
|
#define X_DIAG_PIN P1_29 // X-
|
|
#define Y_DIAG_PIN P1_27 // Y-
|
|
#define Z_DIAG_PIN P1_25 // Z-
|
|
#define E0_DIAG_PIN P1_28 // X+
|
|
#define E1_DIAG_PIN P1_26 // Y+
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#ifdef X_STALL_SENSITIVITY
|
|
#define X_STOP_PIN X_DIAG_PIN
|
|
#if X_HOME_TO_MIN
|
|
#define X_MAX_PIN P1_28 // X+
|
|
#else
|
|
#define X_MIN_PIN P1_28 // X+
|
|
#endif
|
|
#else
|
|
#define X_MIN_PIN P1_29 // X-
|
|
#define X_MAX_PIN P1_28 // X+
|
|
#endif
|
|
|
|
#ifdef Y_STALL_SENSITIVITY
|
|
#define Y_STOP_PIN Y_DIAG_PIN
|
|
#if Y_HOME_TO_MIN
|
|
#define Y_MAX_PIN P1_26 // Y+
|
|
#else
|
|
#define Y_MIN_PIN P1_26 // Y+
|
|
#endif
|
|
#else
|
|
#define Y_MIN_PIN P1_27 // Y-
|
|
#define Y_MAX_PIN P1_26 // Y+
|
|
#endif
|
|
|
|
#ifdef Z_STALL_SENSITIVITY
|
|
#define Z_STOP_PIN Z_DIAG_PIN
|
|
#if Z_HOME_TO_MIN
|
|
#define Z_MAX_PIN P1_24 // Z+
|
|
#else
|
|
#define Z_MIN_PIN P1_24 // Z+
|
|
#endif
|
|
#else
|
|
#define Z_MIN_PIN P1_25 // Z-
|
|
#define Z_MAX_PIN P1_24 // Z+
|
|
#endif
|
|
|
|
#define ONBOARD_ENDSTOPPULLUPS // Board has built-in pullups
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#ifndef SERVO0_PIN
|
|
#define SERVO0_PIN P2_00
|
|
#endif
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN P1_24
|
|
#endif
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN P1_28
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN P2_02
|
|
#define X_DIR_PIN P2_06
|
|
#define X_ENABLE_PIN P2_01
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN P1_17
|
|
#endif
|
|
|
|
#define Y_STEP_PIN P0_19
|
|
#define Y_DIR_PIN P0_20
|
|
#define Y_ENABLE_PIN P2_08
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN P1_15
|
|
#endif
|
|
|
|
#define Z_STEP_PIN P0_22
|
|
#define Z_DIR_PIN P2_11
|
|
#define Z_ENABLE_PIN P0_21
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN P1_10
|
|
#endif
|
|
|
|
#define E0_STEP_PIN P2_13
|
|
#define E0_DIR_PIN P0_11
|
|
#define E0_ENABLE_PIN P2_12
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN P1_08
|
|
#endif
|
|
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN P1_01
|
|
#endif
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#ifndef TMC_SW_MOSI
|
|
#define TMC_SW_MOSI P4_28
|
|
#endif
|
|
#ifndef TMC_SW_MISO
|
|
#define TMC_SW_MISO P0_05
|
|
#endif
|
|
#ifndef TMC_SW_SCK
|
|
#define TMC_SW_SCK P0_04
|
|
#endif
|
|
#endif
|
|
|
|
#if HAS_TMC_UART
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial1
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
#define X_SERIAL_TX_PIN P4_29
|
|
#define X_SERIAL_RX_PIN P1_17
|
|
|
|
#define Y_SERIAL_TX_PIN P1_16
|
|
#define Y_SERIAL_RX_PIN P1_15
|
|
|
|
#define Z_SERIAL_TX_PIN P1_14
|
|
#define Z_SERIAL_RX_PIN P1_10
|
|
|
|
#define E0_SERIAL_TX_PIN P1_09
|
|
#define E0_SERIAL_RX_PIN P1_08
|
|
|
|
#define E1_SERIAL_TX_PIN P1_04
|
|
#define E1_SERIAL_RX_PIN P1_01
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
#define TMC_BAUD_RATE 19200
|
|
#endif
|
|
|
|
/**
|
|
* ------ ------
|
|
* (BEEPER) 1.30 |10 9 | 0.28 (BTN_ENC) (MISO) 0.17 |10 9 | 0.15 (SCK)
|
|
* (LCD_EN) 1.18 | 8 7 | 1.19 (LCD_RS) (BTN_EN1) 3.26 | 8 7 | 0.16 (SD_SS)
|
|
* (LCD_D4) 1.20 6 5 | 1.21 (LCD_D5) (BTN_EN2) 3.25 6 5 | 0.18 (MOSI)
|
|
* (LCD_D6) 1.22 | 4 3 | 1.23 (LCD_D7) (SD_DETECT) 1.31 | 4 3 | RESET
|
|
* GND | 2 1 | 5V GND | 2 1 | NC
|
|
* ------ ------
|
|
* EXP1 EXP2
|
|
*/
|
|
#define EXP1_03_PIN P1_23
|
|
#define EXP1_04_PIN P1_22
|
|
#define EXP1_05_PIN P1_21
|
|
#define EXP1_06_PIN P1_20
|
|
#define EXP1_07_PIN P1_19
|
|
#define EXP1_08_PIN P1_18
|
|
#define EXP1_09_PIN P0_28
|
|
#define EXP1_10_PIN P1_30
|
|
|
|
#define EXP2_03_PIN -1
|
|
#define EXP2_04_PIN P1_31
|
|
#define EXP2_05_PIN P0_18
|
|
#define EXP2_06_PIN P3_25
|
|
#define EXP2_07_PIN P0_16
|
|
#define EXP2_08_PIN P3_26
|
|
#define EXP2_09_PIN P0_15
|
|
#define EXP2_10_PIN P0_17
|
|
|
|
#if HAS_WIRED_LCD
|
|
#if ENABLED(ANET_FULL_GRAPHICS_LCD_ALT_WIRING)
|
|
#error "ANET_FULL_GRAPHICS_LCD_ALT_WIRING only applies to the ANET 1.0 board."
|
|
|
|
#elif ENABLED(ANET_FULL_GRAPHICS_LCD)
|
|
#error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue."
|
|
|
|
/**
|
|
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
|
|
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
|
|
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.)
|
|
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
|
|
*
|
|
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
|
|
*
|
|
* The ANET_FULL_GRAPHICS_LCD connector plug:
|
|
*
|
|
* BEFORE AFTER
|
|
* ------ ------
|
|
* GND 1 | 1 2 | 2 5V 5V 1 | 1 2 | 2 GND
|
|
* CS 3 | 3 4 | 4 BTN_EN2 CS 3 | 3 4 | 4 BTN_EN2
|
|
* SID 5 | 5 6 6 BTN_EN1 SID 5 | 5 6 6 BTN_EN1
|
|
* open 7 | 7 8 | 8 BTN_ENC CLK 7 | 7 8 | 8 BTN_ENC
|
|
* CLK 9 | 9 10 | 10 Beeper open 9 | 9 10 | 10 Beeper
|
|
* ------ ------
|
|
* LCD LCD
|
|
*/
|
|
|
|
#define LCD_PINS_RS EXP1_03_PIN
|
|
|
|
#define BTN_EN1 EXP1_06_PIN
|
|
#define BTN_EN2 EXP1_04_PIN
|
|
#define BTN_ENC EXP1_08_PIN
|
|
|
|
#define LCD_PINS_ENABLE EXP1_05_PIN
|
|
#define LCD_PINS_D4 EXP1_07_PIN
|
|
|
|
#elif ENABLED(CR10_STOCKDISPLAY)
|
|
|
|
#define LCD_PINS_RS EXP1_04_PIN
|
|
|
|
#define BTN_EN1 EXP1_08_PIN
|
|
#define BTN_EN2 EXP1_06_PIN
|
|
#define BTN_ENC EXP1_09_PIN // (58) open-drain
|
|
|
|
#define LCD_PINS_ENABLE EXP1_03_PIN
|
|
#define LCD_PINS_D4 EXP1_05_PIN
|
|
|
|
#elif HAS_ADC_BUTTONS
|
|
|
|
#error "ADC BUTTONS do not work unmodified on SKR 1.3, The ADC ports cannot take more than 3.3v."
|
|
|
|
#elif HAS_SPI_TFT // Config for Classic UI (emulated DOGM) and Color UI
|
|
|
|
#define TFT_A0_PIN EXP1_03_PIN
|
|
#define TFT_DC_PIN EXP1_03_PIN
|
|
#define TFT_CS_PIN EXP1_04_PIN
|
|
#define TFT_RESET_PIN EXP1_07_PIN
|
|
#define TFT_BACKLIGHT_PIN EXP1_08_PIN
|
|
|
|
#define TFT_RST_PIN EXP2_04_PIN
|
|
#define TFT_MOSI_PIN EXP2_05_PIN
|
|
#define TFT_SCK_PIN EXP2_09_PIN
|
|
#define TFT_MISO_PIN EXP2_10_PIN
|
|
|
|
#define BTN_EN2 EXP2_06_PIN
|
|
#define BTN_EN1 EXP2_08_PIN
|
|
#define BTN_ENC EXP1_09_PIN
|
|
|
|
#define TOUCH_BUTTONS_HW_SPI
|
|
#define TOUCH_BUTTONS_HW_SPI_DEVICE 1
|
|
|
|
#define TFT_BUFFER_SIZE 2400
|
|
|
|
#ifndef TFT_WIDTH
|
|
#define TFT_WIDTH 480
|
|
#endif
|
|
#ifndef TFT_HEIGHT
|
|
#define TFT_HEIGHT 320
|
|
#endif
|
|
|
|
#define LCD_READ_ID 0xD3
|
|
#define LCD_USE_DMA_SPI
|
|
|
|
#if ENABLED(TFT_CLASSIC_UI)
|
|
#ifndef TOUCH_CALIBRATION_X
|
|
#define TOUCH_CALIBRATION_X -11386
|
|
#endif
|
|
#ifndef TOUCH_CALIBRATION_Y
|
|
#define TOUCH_CALIBRATION_Y 8684
|
|
#endif
|
|
#ifndef TOUCH_OFFSET_X
|
|
#define TOUCH_OFFSET_X 689
|
|
#endif
|
|
#ifndef TOUCH_OFFSET_Y
|
|
#define TOUCH_OFFSET_Y -273
|
|
#endif
|
|
#elif ENABLED(TFT_COLOR_UI)
|
|
#ifndef TOUCH_CALIBRATION_X
|
|
#define TOUCH_CALIBRATION_X -16741
|
|
#endif
|
|
#ifndef TOUCH_CALIBRATION_Y
|
|
#define TOUCH_CALIBRATION_Y 11258
|
|
#endif
|
|
#ifndef TOUCH_OFFSET_X
|
|
#define TOUCH_OFFSET_X 1024
|
|
#endif
|
|
#ifndef TOUCH_OFFSET_Y
|
|
#define TOUCH_OFFSET_Y -367
|
|
#endif
|
|
#define TFT_BUFFER_SIZE 2400
|
|
#endif
|
|
|
|
#elif IS_TFTGLCD_PANEL
|
|
#if ENABLED(TFTGLCD_PANEL_SPI)
|
|
#define TFTGLCD_CS EXP2_08_PIN
|
|
#endif
|
|
|
|
#define SD_DETECT_PIN EXP2_04_PIN
|
|
|
|
#else // !CR10_STOCKDISPLAY
|
|
|
|
#define LCD_PINS_RS EXP1_07_PIN
|
|
|
|
#define BTN_EN1 EXP2_08_PIN // (31) J3-2 & AUX-4
|
|
#define BTN_EN2 EXP2_06_PIN // (33) J3-4 & AUX-4
|
|
#define BTN_ENC EXP1_09_PIN // (58) open-drain
|
|
|
|
#define LCD_PINS_ENABLE EXP1_08_PIN
|
|
#define LCD_PINS_D4 EXP1_06_PIN
|
|
|
|
#define LCD_SDSS EXP2_07_PIN // (16) J3-7 & AUX-4
|
|
#define SD_DETECT_PIN EXP2_04_PIN // (49) (NOT 5V tolerant)
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
#define DOGLCD_CS EXP1_08_PIN
|
|
#define DOGLCD_A0 EXP1_07_PIN
|
|
#define DOGLCD_SCK EXP2_09_PIN
|
|
#define DOGLCD_MOSI EXP2_05_PIN
|
|
|
|
#define LCD_BACKLIGHT_PIN -1
|
|
|
|
#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
|
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
|
|
|
#define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally.
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN EXP1_05_PIN
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN EXP1_04_PIN
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN EXP1_03_PIN
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN EXP1_05_PIN
|
|
#endif
|
|
|
|
#else // !FYSETC_MINI_12864
|
|
|
|
#if ENABLED(MKS_MINI_12864)
|
|
|
|
#define DOGLCD_CS EXP1_05_PIN
|
|
#define DOGLCD_A0 EXP1_04_PIN
|
|
#define DOGLCD_SCK EXP2_09_PIN
|
|
#define DOGLCD_MOSI EXP2_05_PIN
|
|
|
|
#elif ENABLED(ENDER2_STOCKDISPLAY)
|
|
|
|
/**
|
|
* Creality Ender-2 display pinout
|
|
* -----
|
|
* 5V | 1 2 | GND
|
|
* (MOSI) P1_23 | 3 4 | P1_22 (LCD_CS)
|
|
* (LCD_A0) P1_21 | 5 6 P1_20 (BTN_EN2)
|
|
* (RESET) P1_19 | 7 8 | P1_18 (BTN_EN1)
|
|
* (BTN_ENC) P0_28 | 9 10| P1_30 (SCK)
|
|
* -----
|
|
* EXP1
|
|
*/
|
|
|
|
#define BTN_EN1 EXP1_08_PIN
|
|
#define BTN_EN2 EXP1_06_PIN
|
|
#define BTN_ENC EXP1_09_PIN
|
|
#define DOGLCD_CS EXP1_04_PIN
|
|
#define DOGLCD_A0 EXP1_05_PIN
|
|
#define DOGLCD_SCK EXP1_10_PIN
|
|
#define DOGLCD_MOSI EXP1_03_PIN
|
|
#define FORCE_SOFT_SPI
|
|
#define LCD_BACKLIGHT_PIN -1
|
|
#endif
|
|
|
|
#if IS_ULTIPANEL
|
|
#define LCD_PINS_D5 EXP1_05_PIN
|
|
#define LCD_PINS_D6 EXP1_04_PIN
|
|
#define LCD_PINS_D7 EXP1_03_PIN
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
|
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
#endif // !CR10_STOCKDISPLAY
|
|
|
|
#endif // HAS_WIRED_LCD
|
|
|
|
#if NEED_TOUCH_PINS
|
|
#define TOUCH_CS_PIN EXP1_06_PIN
|
|
#define TOUCH_SCK_PIN EXP2_09_PIN
|
|
#define TOUCH_MOSI_PIN EXP2_05_PIN
|
|
#define TOUCH_MISO_PIN EXP2_10_PIN
|
|
#define TOUCH_INT_PIN EXP1_05_PIN
|
|
#endif
|
|
|
|
/**
|
|
* Special pins
|
|
* P1_30 (37) (NOT 5V tolerant)
|
|
* P1_31 (49) (NOT 5V tolerant)
|
|
* P0_27 (57) (Open collector)
|
|
* P0_28 (58) (Open collector)
|
|
*/
|
|
|
|
// Include common SKR pins
|
|
#include "pins_BTT_SKR_common.h"
|
|
|